# 1
Swagman XTC2 Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
First-time rack buyer / owner / installer. The rack arrived in a timely fashion, maybe a day or 2 ahead of schedule. It was well packaged. I’m LOVING this bike rack. It was easy to put together and to mount on my new Honda Passport. Thus far, no squeaks in my 2” receiver. Hardest part of initial set-up is figuring out the best way to position two bikes. Trial & error and some patience. The directions weren’t clear as to where the 2 left-over screws went. I found the answer in another review and have posted a pic in case others have the same problem (photo with pen pointing at screw). These screws go in the underneath side of both of the folding arms. They appear to keep the wheel wells from sliding off in case in you drive with an empty, un-folded rack, and forgot to tighten down the wheel wells. The folding arm push / pull pins can be difficult at times. I coated the tips with some lube. That and a little jiggling seems to solve that issue. I guess it’s better for the pins to be snug vs popping right out. I added a small Master lock to the hitch pin (in lieu of the provided cotter pin) as a theft deterrent. I read that a 3/16 shackle lock will fit into the bike clamp down arms to also act as a deterrent. I had an old 3/16 lock that did snugly fit and appeared to be locked. HOWEVER, I yanked on the lock and it came open as there isn’t quite enough clearance for the shackle to lock. I discovered that longer 3/16 shackle locks are hard to find. Have attached a photo of the lock that actually fits and works (Ace Hardware). One lock on the upper clamp down arm will secure both arms as the lower arm can’t be removed without removing the upper arm. The clamp down arms appear to be coated to prevent damage to your bike. I’ve tried a simple rag and ultimately settled on pool noodle pieces as a precautionary measure. I CAN NOT open my tailgate (regardless of whether or not the rack is fold up and in the bike carry position). If that’s a concern for you, then spring for the more costly titling version. My back-up camera still functions.
The Swagman XTC-2 platform bike carrier arrived very quickly from etrailer and in good shape, the actual carrier box is inside another shipper box, which I'm sure helped with its condition. Assembly was relatively quick and painless, even though the instructions could be a little more thorough. Installing the carrier on the back of our Jeep Patriot also was quick, it helps to have an extra ratchet & 3/4" socket laying around for just this purpose. Installing the bikes takes a little patience and trial and error the first time you try and put them on the carrier. It's easy enough to adjust the wheel holders to fit the wheelbase of your bikes, but for us at least, the challenge was trying to swing the vertical support bar up into position after putting on the first bike (closest to the Jeep). We couldn't angle the bike enough toward the Jeep to have the bar clear the bike. We learned that the easiest way to secure the first bike was to remove the ratcheting frame hooks altogether, put the bike in the carrier, swing up the vertical support bar, put in the pin, and then slide one of the frame hooks down on the bar. The outside bike is much easier because you can set the bike in the carrier at whatever angle you need, not being limited by the back of the vehicle. One thing we did to protect the bike frames was to use some foam pipe insulation as cushion between the frame hook and the frame (see pictures). Once you get a system for installing the bikes, it is very quick to load/unload them. The rack seems to be well made and doesn't wiggle excessively when traveling. All in all a good product for a good price, would definitely recommend it for anyone looking for a platform bike carrier.
# 2
Swagman Truck Bed Bike Rack for 2 Bikes - Fork Mount - 9-mm Skewer
I used 2 inch square tubing cut the length of the tie down support bracket in my 2007 Honda Ridgeline and secured with a stainless bolt and wing nut, use a large enough washer to cover the diameter of the supply hole in the Honda Ridgeline bracket on the truck. A couple of notes: Be sure to use something as a cushioning gasket to insure a snug fit and to protect your truck lining. I used rubber or foam exercise mat cut to the same as the aluminum square tubing. Use a washer that a combination of hard plastic and metal to avoid the corrosive effects of dissimilar metals in contact with each other. last: My 26" full suspension bike fits, but I have swing it to one side slightly before i close the tailgate and lift the bike up and slide it down....It's a very snug fit but the suspension adds pressure to the tailgate and its works out very well. Or you could just use a tailgate extender.
Referring to special mounting instructions if you have a bed liner: (line #3). I do not have a bed liner, but I do have a molded plastic cap on my bed rails ('04 Ford F350). The first install over the plastic cap the locking pin or pin as called out in line #3 was nowhere near making contact with the metal lip of the metal bed under the plastic. What I did next on the second and final install was remove/cut away the plastic on the inside of the bed rail to allow the vertical portion of the "L" mounting bracket (Fig 4) to contact the metal bed. The locking pin is now at a position almost where it would protrude under the metal bed lip if I would remove the rest of the plastic under the horizontal portion of the "L" mounting bracket, I did not do that. After cutting a notch in the metal rail to accept the pin, the pin barely flushes out to secure the rack. A 1/4" longer pin would take care of this problem. One other thing that was not addressed in the install instructions was if you have a full size pick-up bed you are likely to attach the passenger side fork mount (Fig 2) to the right of the extension tube locking mechanism. The extension tube is a smaller diameter, so you will have resize the fork tube clamp (Fig 1) for the smaller tube. I can't explain how to do it other than it's a Chinese puzzle.
What our customers are saying:
"great experience!!! I've been looking for a hitch. With the experience I just had with the bike rack, I;kk definitely come back and order the hitch when I have a little more $$$. delivery was quick! the product was awesome!!! Frank"