Most Popular EcoHitch for 2021 Toyota Tacoma

Bolted right up to my 2019 F-250. Looks like it's going to work perfect to haul my E-bike rack. I might have to use a dual receiver hitch to drop the rack down for better visibility while driving. That's to be determined. I'd highly recommend the Eco Hitch!!

Click to Enlarge

Click to Enlarge

I'm 59 years old and a third generation grading contractor. I've worked on trucks and heavy equipment my whole life. I've turned ALOT of wrenches. That being said, the instructions for installation of this hitch are the worst I've ever seen. Lots of steps left out of the bumper removal. The instructions for cutting the plastic where the hitch goes were not even close! Multiple attempts and additional trimming to make it fit. Also the hitch was an extremely tight fit between the rails. Once installed I like it and it seems to be good quality. The one star is for the almost useless instructions.

Fit nice. I haven't used it to move a trailer yet. I didn't have tow hooks and the factory ones are high so I paid the extra to get the hitch instead.

Perfect hitch for those needing a rack for extra space. I used a heavy duty vinyl bag to enclose my tools, cords and generator on my 12k mile trip to alaska. The held that 500lbs extremely well across the permafrost damaged Alaskan highway! No twists, no bends and no worries!

Click to Enlarge

Review for truck front hitch receiver I finally Installed the front receiver hitch today, I pulled it out of its package and found all parts wrapped to the receiver hitch good call as there was a hole in the box. The license plate holder received some damage it was bent some. Installation. I reviews the video prior and read the instructions. Had to purchase a 4 inch hole saw and a torque wrench that added to the cost of the hitch. Installation was for the most part straight forward, when the video cuts from shot to shot I now know all the cussing and swearing are done during that time as it’s very difficulty to get the hitch in over/under the exiting hardware, solo installer took me 3.45 hrs to install, tight fit under the truck to maneuver under the truck. Bolts back into original tow hooks was a total Pain in the A$$ trying to hold up the hitch and the hooks while trying to maneuver the hold back in. (Had to take it out as I inserted on the wrong side) I will say that installation is doable by novice front yard mechanic but with a difficulty of 7 out of 10, trying to get the bolts torqued to specs is difficult due to clearance and angle of the bolts. Make sure you have deep well sockets because the new bolts for the hitch and long and a standard size socket will not be able to grip the nut as you tighten it down to specs. Put the bike rack on the hitch receiver and found that the hole that we drilled out to put the hitch in is not big enough. The bolt for the hitch goes in from the right and there was barely enough room to get it in the hole, used a wrench to tighten it but it was slow going, the other issue was that on the left side there is a hitch lock I struggled to get it on, but then could not reach in to remove the key. So final outcome was I had to drill out another 4 inch section of the bumper to get to the key. If your hitch has a bolt on bike rack like the swagman e-bike rack you want it to be secure so the bolt is a must this option may not be the best option. The bikes block the headlights so no night driving with the bikes on the rack. The handlebars need to be folded down otherwise the bikes will ride too high on the front and obstruct your vision. If I had to do it again I would have gotten the hitch that is lower and would not have to drill out my bumper, and it would have given me more visual clearance. I did take a shot drive with the bikes in front it will take a bit to get used to them being in the front as well as making wide turns while towing the RV that I don’t take out the car in front of me.

My friend installed the hitch and I helped . But mostly by staying out of his way!?? Everything worked out perfectly!!! Thank Y’all for the Great Service

This is a very sturdy and well-made hitch. Installation was fairly straight forward - the directions and video are very good. My truck is a 2024 Silverado 2500 HD in High Country trim (why pay less?) so, the fairings/moldings under the front bumper were slightly different, but nothing that was not easy to adjust to. The measurements in the instructions were right on. As you can see in the photos, we have two ebikes that we plan to haul around while we pull our camper. The hitch and bike rack set up appears to be very secure and stable. They sit a little higher than I would like, but not any higher that the snowplow lights I had on a truck I has way back in the day... I'm pretty good at backing the camper (28 ft), but I am also looking forward to testing out pushing the camper into it's fairly tight parking pad. I've never done it, but I hear it works well in close spaces. Lastly, this is the second hitch I have purchased from etrailer. We added one to the back of the wife's Rav4 last fall to haul this same bike rack and bikes. It also works great (tight, stable and secure) except note that the Toyota installation was a little more challenging as there is very little room to work & insert the bolts, however, no cutting was involved. It looks nice. In any case, both transactions were great. If I had another vehicle that needed a hitch, I would purchase it again from eTrailer. Much thanks to all.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Super fast, free delivery. Box came in damaged, but the product was undamaged and complete. Installation instructions and video were spot on. Currently set up for a 12000 lb. inline pull winch, but the options are almost limitless. I'll possibly install a step to make access easier for under the hood work. As always, thanks etrailer.com.

Great fit, instructions and materials worked perfectly

Click to Enlarge

Click to Enlarge

Installed the hitch this morning, all went as anticipated. The directions provided were excellent and if you couple the videos you will have no problem with the installation. Just take your time. Have fun with the installation. Did do one thing different from the directions and used a 1/2 drill bit to create a radius on the inner side of the air dam cut outs, the radius made a custom tight fit around the receiver tube.