# 1
Bulldog Square Jack - Drop Leg w/ Spring Return - Sidewind - 26" Lift - 10,000 lbs
This was a replacement jack for a flat bed trailer. Installed it and it was just like the old one. Very happy with the jack, I recommend it highly.
Heavy duty, well-built jack. I decided to upgrade my trailer jack for poor performance and after searching the net I came across a video from etrailer describing the features of the Bulldog Square Jack # BD182804. It has every feature you need and some. With the upgrade, I must mention there was welding involved. I first confirmed there was structural support where the jack was to be mounted. I disassembled the jack per the video, located and welded the housing in place, reassembled the jack and lubed with the same grease I use for my trailer axles. It was that easy.
# 2
Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - Black
Overall the product does exactly what it's intended for and works well. I however assumed that this would be a simple R&R for my camper and did very little installation research other that the video provided on etrailer' s website Sadly it did not fit. Not at all. I didn't take into account that have a double framed hitch toyhauler. The baseplate on the factory leg was a TRIANGLE.....this unit was ROUND. Also the primary shaft was thicker than stock and would not drop down into place I know modifying is frowned upon, but I found that ALL powered hitch legs I found have round mounting plates and it's not mentioned the leg tube is thicker than OEM? Since NOT having a power lift wasn't an option for this camper application...too heavy in the front when ATVS loaded to lift for setting the equalizer hitch tension bars, I proceeded to modify by cutting the rear rounded mounting base ... square. Took off about 1/2 inch. Then I took my metal Dremel sanding bit and increased the hitch leg hole diameter slightly. Took about 1 hr. Dropped it in. Wired it. Tested it. All good. If you can't post this I understand, but take note that some of your website descriptions may need to be enhanced. Thanks!
This has been a great trailer jack a year into installing it on my 12 x 6 enclosed cargo/camping trailer. The jack is out in the elements 24/7, gets used almost every weekend and is still going strong. I would definitely purchase this product again for my next trailer.
# 3
Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 3,500 lbs - Black
I received my new Bulldog jack fast after placing my order. It took me about 20 minutes to remove my old one and install the new one. This Bulldog jack is quieter than the previous one and moved up and down real well. I needed to hook up in the evening before I left for my camping trip and will say the nice led light this jack comes with gives a very nice lighting to be able to see everything needed to hook up my trailer to my truck. I hope this one lasts much longer than my previous one. Time will tell but so far I really like the way this Bulldog jack operates
Excellent Jack. Slow moving but that is due to high torque. Well made, attractive design. Highly recommended! Solved the problem of busting my knuckles on the propane tanks while cranking the old jack.
# 4
Bulldog Powered-Drive Trailer Jack - Drop Leg - A-Frame - 21-3/4" Lift - 3,500 lbs - White
The bull dog electric tongue jack is awesome. I got it in white to match my trailer. I unbolted the old jack and bolted on the new one in about 5 minutes. (I had my coreless impact gun.) Total install time was about an hour mainly because I wired the jack to my battery inside the trailer that runs the electronic winch and I had to run a separate ground from the battery to one of the mounting bolts for the jack with a cut off switch. So far it works great but time will tell. I'll be using it a lot more next year.
Excellent customer service and followthru by etrailer. Jack is well built and easy to install and use. Would definitely add a flat washer under the bolts to prevent the lock washers from getting drawn into the oblong bolt holes when torquing them done.
# 5
Bulldog Tandem Landing Gear Set - Drop Leg - 36" Lift - 8,000 lbs
Delivery was on time, but the box it arrived in didn’t fair we’ll and parts were hanging out of the box! But everything was accounted for and the parts were well wrapped. Installation was very easy. The only issue was the locking pins mount plate is tack welded to the primary leg that the motor moves up and down. Those mounting plates had to be removed to install the lead and follow jacks. A grinder made short work of that. I didn’t put the mounting plates back on, instead I used my spring loaded pins that were on the old legs, they were still in good working condition. Also I didn’t use the adjustable cross over rod that came in the package . I opted to use the one that was on my old jacks, it was constructed of heaven gauge tubing and didn’t have a much (slop) movement in it. Also did not use the plastic housing gear box, I purchased a aluminum house gear box from e-trailer a few months back and used that one keeping the plastic for a spare. Very satisfied.
The leg pin came out because of the design, it is not a strong locking mechanism to not pull it all the way out. (My wife pulled it all the way out) Afyer furthet inspection, in addition to poor locking mechanism, the size of the pin is not adequate for the specified weight of the jack.
What our customers are saying:
"Received already. Yeow! Perfect fit. Thanks for getting the kit to me so quickly."