Most Popular Canoe for 2015 Honda Odyssey

As all Thule products the Thule universally mounted canoe carrier is great. It came with all required items for safe and easy canoe transportation. There are two straps with pull to fasten for the canoe down, two tie down ropes for each end with nice pull tight and release mechanisms for the cord as well, along with two straps to fasten to the canoe ends used with the pull to tighten cords. The Chevy traverse cross bar had to have the plastic end caps removed for use with Thule canoe carrier. This was because my canoe took up the entire cross bar width to allow for Thule mounts. It is not a big deal to remove the plastic end caps. They only provide a finished stream lined look. Happy and Safe Canoeing

Click to Enlarge

Click to Enlarge

Click to Enlarge

After retiring my 1999 Chevy Silverado 4x4 pickup, I purchased a 2017 Subaru Outback as a replacement vehicle. To transport my 1981 17 foot QT17C Alumacraft canoe on the factory installed roof rack crossbars that came with the Outback, I selected the Thule Portage Canoe Carrier w/ Tie-Downs - Gunwale Brackets - Side Loading - TH819 to do the trick. With one previous transport of the canoe sitting directly on the Outback roof racks, I realized those Outback roof racks were not as durable as the racks on my truck so I sought an improvement to avoid future scuffing and scratching. I did some advance research online and couldn’t be more pleased with this purchase from etrailer.com. I now have a quality product at the right price and these gunwale brackets are a simple solution for this veteran canoe man. The padded brackets grip the canoe and stopped the scratches. The high-quality load straps are nice with the rubber pad that covers the buckle and they easily snug the canoe tight to the racks. I’m also impressed with the bow/stern tie downs that have a very nice ratchet and clip on one end and I secured the supplied hook with a bowline knot to the other end of the ¼ inch rope. The Outback did not have convenient anchor points on the front or back of the vehicle for tie down locations but I found a good solution there as well by ordering the Thule Bow/Stern Tie-Downs - Qty 2 - TH530. This works well with the tie downs I mentioned previously. One limitation to be aware of with the Subaru Outback roof racks and this product is the width of your canoe. My 17-footer measures 34 inches at its widest point at the portage yoke. I had to place the four brackets up tight against the inside roof mounting to achieve the spread and accommodate the canoe placement. The canoe ended up fitting like a glove on the padded brackets. When placing the strap to hold the canoe down to the crossbars, I ran the strap through the vehicles tie down points and then under the crossbars for added security. Total product installation time including securing the canoe can easily be achieved in approximately 20 minutes. I look forward to many more years of safe and happy canoeing. I give etrailer.com an excellent rating for the entire ordering and shipping process on top of the high level of satisfaction with the products I purchased through them. Their customer service and price ensured me that I’ll do more business with them in the future.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Product was as advertised, however it was missing four bolts that I had to get at a hardware store, but other than that it was fine. Service from etrailer team was outstanding.

I've been using the product for two summers now and it is perfect for what I'm using it for. My canoe is an Old Town Discovery 133, it's very wide and I initially had trouble fitting it in the brackets with how relatively narrow my Rav4 is, but the instructions that came with them mentioned I could just flip them around. That worked perfectly. I only use the brackets and the tie down straps from the kit to tie the boat to the crossbars, and then use the painter lines I put on the bow and stern of the boat to tie those to the car. That rides on the highway very easily with no shifting. With two people, the load/unload time is around 10 minutes as long as one person knows what they are doing. This kit had exactly what I was looking for, seems built to last, and if I ever need another kit to help tie a canoe to a car then I know I can trust this product to get the job done safely and reliably.

I have (2) Wilderness Systems Pungo 120 kayaks and was looking for something better that the cheap J-Shape kayak holders that I purchased elsewhere. Unless you are tall enough to lift the kayaks and install them from the side, the loading of a kayak on it's side is unwieldy and somewhat frustrating to keep the kayak from flipping to a horizontal position. I am using the factory racks with crossbars on my 2006 Toyota Highlander. I was looking for a solution that would allow me to load 2 kayaks with the keel down. Using a large bath mat to protect the paint I was able to load the kayak by myself and I am 5'6". The one thing that they could improve is that the rubber pads on the wings are very tacky. Once that you set the kayak onto the wings, the kayak will not move back and forth. You will find it very hard to move the kayak front to back once it is set in the cradle. This is a good thing since the kayak could slide off should a strap fail. The Pungo 120 has multiple angles so the contact with the wings are very minimal. The rubber does keep it in place before strapping them down. Once you load the kayak onto the wings, it will stay where it is.. it is a kind of a struggle to move the kayak.. a solution is to throw large beach towel on the wings before loading your kayak and you can position the kayak with ease. Once you have centered your kayak, lift the kayak one end at a time and remove the towel. Bow and stern tie downs are necessary to completely secure your kayak. The wings are 28" across and will rise 6" above your crossbars that you attache them to.

Click to Enlarge

Click to Enlarge

Bought two sets for two boats. Installed on a 2020 Forester and will be able to carry two boats side by side. Sturdy racks and easy to assemble and install and will be easy to remove when not in use. They will also fit on truck racks so the ease of install/removal will be a real plus. Side by side mount on this vehicle required placing the racks a little more outboard than I like but should not cause any problems. I will strap the boats to the crossbars as suggested in the instructions for additional stability. PS. one set was returned merch. Got a better price and can't tell that it was ever out of the box. Yay me.

Click to Enlarge

Click to Enlarge

The Malone Bigfoot Pro Canoe Roof rack is excellent and is super strong. I have two sets of them now, one for a Malone Aero Bars Car Roof Rack, and one for a Rhino Aero Bars Car Roof Rack (both bought at Etrailer). The quality is first rate, so why the 4 stars? The reason is that the support back of the canoe racks is too high. It only needs to be one inch high which matches the rubber pad. Instead it is 3.75 inches high. Every inch higher than necessary makes it harder to lift the canoe over the backs of the canoe racks. If I could cut them easily I would do it, but it looks like it would be too difficult to cut the metal back down to 1 inch. The Canoe racks are even better using the T-Slot Integration Hardware Kit for Aero Styled CrossBars, MPG915. That kit has 5/8" long (functional length) bolts which fit the Malone Aero Bars Car Rack. For the Rhino Rack, it uses a different kit that has 7/8" long bolts. Using the T Slot allows full use of the entire aero bars.

I bought these brackets for my Ascend H-12 kayak. The kayak transports face-down on Thule roof racks. These high-quality brackets are easy to install/remove and inhibit any side to side slippage while providing a secure tie-down. I highly recommend these brackets for anyone transporting canoes or kayaks on their rooftops.

I purchased these for my Thule Aero bars and they are perfect. I needed to protect the cherry gunwales of my canoe during long road trips The pieces of foam pipe insulation I was using were definitely not up to the task and kept blowing off! The velcro attachments on these puppies are bombproof.

Click to Enlarge

Great product easy install fast ship honest seller these are for my ladder rack to carry very heavy ladders without hurting my rack

Awesome invention. Greatly reduced the amount of time and frustration usually associated with loading up our 2 SUPs and small sport kayak. It does take some time to install but that is expected. Don't assume the initial installation is a 10-minute job. However, once the system is in place, loading and locking the SUPs and kayak was simple and quick. We did have to experiment a bit with the best combination to make everything fit. I was hoping we could fit three SUPs on one rack, but no chance. My only complaint is that the keys provided are plastic, and strip very easily when unlocking the bars to remove or make adjustments. Without a key, your stuff is stuck. We hope that LockRack with come up with a more sturdy, metal replacement key for this system.

The keys are an issue (wish they were metal), but everything else is great! I go sunrise kayaking only and hate putting straps on with cold hands at 3:30 in the morning. I have a Nissan Pathfinder and was able to put this on with another set of Malone J-hooks so that I can have a second kayak when I go with someone. Once the fear subsides of it possibly falling off, you realize how quick and easy this thing is to use. It takes me 1 minute instead of 9-18 minutes to get my kayak up and secure. I have tested it at 75mph without any jiggling or issues. I sat on this in my shopping cart forever and finally pulled the trigger. If you kayak at least 10 times a year or are going at high speeds for extended periods of time in warm weather, totally worth it. If not, well, there are cheaper options out there.

The product itself I would give 5 stars, but it took considerable effort before I could get it installed and tried out. The first obstacle I ran into is that there were no screws included. After opening the box I discovered this, read through the manual, looked at the product listing on etrailer's website, and on Thule's website. I did not see any notice that screw were not included. Finally I did see on one end of the box such a notice, and etrailer's customer service confirmed this to be the case. The second obstacle was how to install the product in my garage. The instructions were of marginal help. They are mostly devoid of words, but rather use pictures to instruct. Once I had a good idea of how all the parts were to fit together and be mounted I discovered my garage ceiling would not accommodate the parts. The ceiling rafters are installed on end, from one side of the garage to the other, and thus not wide enough for the screw holes in the pulleys or center rod mounting brackets. I improvised by installing in the garage attic two 2x8 boards perpendicular to the rafters, then three 2x4 boards snug under the garage ceiling, attached to the 2x8s by way of two 3/8 x 3.5" hex bolts on either end of the 2x4s. The 2x4s were 10', cut in half to allow room for the TH572 mounting hardware between the bolts. With appropriate structure in place (a 12-hour one man job), I started on installing the product. I used eight 1/4 x 1.5" lag screws to attach the pulleys to the 2x4s, and six #10 1.5" wood screws for the center rod mounting brackets. This part of the job took only about an hour... maybe two... it was late. Some suggestions: - make sure your garage can hand the load of the box (What you see in most attics are designed to hold the roof, not have stuff suspended from them -- I got lucky and had access to reinforced headers in the right places) - make sure your garage door can still open with whatever you are storing in place - make sure you can get your car in position under the load (rooftop box, kayak, etc) where everything is installed - make sure you can get your car out of the garage with the load attached So, my main complaints with this product are two: no screws, and minimal instructions. But with a little determination and some help from etrailer customer support, I was able to get the job done. Now I need to find someone who can make my garage door opening taller.

Click to Enlarge

Overall I give this Thule Multilift Cargo Lift a five star rating; however installing this device takes some effort and skill. Maybe more effort and skill than the typical DYI'er can provide. The instructions provided do not have any words or dimensions, only pictures. Other than following the routing of the rope through the pullies it didn't provide me any benefit. Also, my system did not come with any screws or bolts. For me that was not a big deal as I have plenty of hardware I can use. There is one center bracket and four pullies to install. The spacing does not line up with typical dimensions so I had to improvise to get the Multilift installed. My garage ceiling has joist spacing that is 16" on center. That is typical, although some may have 24" on center spacing. Either way the spacing for the screws to secure the various components does not match. I guess you could use toggle bolts to hold the components to the ceiling sheetrock but I didn't trust that idea. What I did was to span my ceiling joists with 1"x4" wood and then attach the components to them. The kit comes with a template so getting the actual components set up on the 1"x4" wood strips was simple enough. Once all the components are installed then the rope is routed through the pullies. As you can see in the pictures I had a close clearance between the roof box and my roll-up garage door. I think it is about 2". Since I don't have a tall roll-up garage door I cannot drive my car in or out with the roof box installed. That didn't matter to me since my only goal was to store the roof box out of harms way. My last comment is that it takes two people to lift the roof box up and get the Multilift ropes in place. I tried to do it by myself but that did not work. I do like this Thule Multilift but it took some effort to install it. I really like the way it is raised and lowered by turning a mechanism with a handle. There is a less expensive lift sold on the internet but it did not use as many pullies to raise and lower the roof box and it relied on a rope to lift and lower it.

Click to Enlarge

Click to Enlarge

Very good quality materials for the price point. No tool Assembly and installation is a bonus. I’ve used them for two weeks now, hailing in both two kayak and single kayak configurations. The lever that you pull Up/down on is going to break. Period. If you have the rotating level too tight you can’t switch it up or down and if you have it too loose, it will come unscrewed and then you have a hard time longing up that no internal thread to get it back on. Also, it’s a pain to have to move the entire system to reconfigure needs. Would be nice if it had a slide and lock back in option once on the cross bars. Pulling off 16 wing nuts isn’t ideal. The video was great, appreciated that. Do wish they had shown how to tie down when using two kayaks because once you have one on the system when you place the second on the opposite side, you no longer have access to that center rack. Shipping speed was excellent. The quality of the cam straps is impressive. I have a hand injury and so getting the bolts secured was difficult. The fact that they come with two different lengths to accommodate different rack heights was really nice. Make sure you have your cross bars 24” apart as the instructions say.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This carrier has worked out really well! I paired it with the SportRack Semi-Custom Roof Rack for Naked Roofs - Square Crossbars, and the carrier attached to it perfectly. I drive a 2014 Honda Civic and this carrier has been able to transport two kayaks with no problems. Highly recommend, especially considering the price.

Click to Enlarge

Click to Enlarge