# 1
Ultra-Fab Stackable Stabilizers for Small Trailers and Campers - 6,000 lbs - Qty 4
These Jack's made both building and positioning my teardrop onto the trailer bed easier. At campsites they easily level the trailer. So yes I'm happy.
we are using these stabilizers for supporting our offloaded truck camper (adventurer 910db) where we reside full-time ... they are very easy to use, provide excellent support for the truck camper and have eliminated 98% of wobble ... the support structure includes jack pads, e-trailer stabilizer, 2x6 pressure treated lumber, 4x8 3/4 inch pressure treated plywood
# 2
Ultra-Fab Stackable Stabilizers for Small Trailers and Campers - 6,000 lbs - Qty 2
Perfect for the four corner supports of our Jayco 175 RD. Much easier to deal with than the scissor jacks installed on the camper. E trailer got them to us quickly as usual!
Our camper came with stabilizers only in the back. Once we level it we put these under the front corners and it gets rid of any movement in the camper like you get when front is only on tongue jack.
# 3
Lippert Electric Landing Gear Set - Weld On - 37" Lift - 6,000 lbs
Received the Kit in about four days (5 Stars for etrailer). The shipping container was severely damaged (2 stars for UPS), but at least it arrived. Did not appear any parts were missing. I ordered this kit because it was less expensive for the complete kit then to replace both landing gear legs separately. I left the 5th wheel attached to the truck and removed the old landing gear, gearbox, and motor prior to the arrival of the new system. Keep all your parts. The new kit arrived and was very easy and straight forward to install. However the tubular steel expansion rod that connects both landing gear legs was too short. I had to use the my old connection rod. Also the spacer used for the inside of the large side of the connection rod was not included with the kit. Had to use the old spacer in the old connecting rod. I used my old landing gear foot plates and pull pins on both landing gear leg extensions. Once installed, the kit worked flawlessly. I placed red marker tape on the landing gear extensions so not to top out the legs when lifting. Again save all your old parts.
I installed the jacks on my 23 ft. 5th wheel trailer, which was very simple and ran the electric wires direct to my battery compartment. The jacks work fine but are a bit too noisy for my liking. Not sure if all are this noisy but they do the job.
# 4
Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors - 30" Lift - 6,000 lbs
Finally got around to installing my PT II Stabilizers 30" front and rear of our 26' Surveyor. Pre - assembled them to make sure they went together ok. Luckily I had two sources for power front & rear which made wiring easy, I used a Buss block to make all positive connections, grounds straight to frame, soldered all connections and heat srinked to seal. Using the 3/8" self tappers was fun.Well got it all together and all works well makes trailer very stable, don't have to worry about scissor jacks collapsing anymore.
I finished the assembly and install of the power twin II stabilizer and have included pictures of the install. This is a good quality unit and I am very happy with how it works. Bob
# 5
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs
Product was an exact fit for my application only problem I had was key inside gear box fell out but easily fixed once I figured it out.etrailer was spot on helping me find correct jack for my ca.per works great
I thought replacing the landing gear would be much harder on my 5th wheel but they when in without a problem and are still working great. The video walks you through the installation step by step. Rick
What our customers are saying:
"I ordered this merchandise on one day and by the time I went home from work on the next day it was in my driveway. Amazing service."