Most Popular Fixed Height for 2009 Hyundai Sonata

E trailer I have a 2019 Mazda6 and purchased the rhino rack series 2500 parts (fit kit #DK289, foot pack #RRRLKVA, aero crossbars#RRVA126B-2), and the rhino rack snowboard/ski carrier #RR576. My car does have fixed mounting points underneath the strip on the roof so I opted to add them to my roof and not use the clamp for kit that goes in the door jam. Every time I entered the year, make, and model of my car, the parts came up with the clamp fit kit part #DK387 which I did not want. But after some research, I found the correct fixed mounting point fit kit. The site of course told me that this part wouldn’t fit my car but after looking at the customer reviews, I saw them used on Mazdas. All of the rhino rack instructions were not the best. We did have to make some adjustments. One of the instruction packs tells you how long you’re supposed to cut the rubber pieces that go into the crossbars based on your car but unfortunately, the measurements were wrong for my car (picture- front 166mm is wrong). The front bar length was about an inch too short and I had to add more rubber to make it longer to fit the fixed mounting points on my roof. After some time of trying to interpret the instructions, and looking up whatever available instructional videos were online, we finally finished installing them and they do look really nice. At higher speeds on the highway I can definitely hear more noise. The actual snowboard carrier is fine, fits all 4 boards fine. It is a little difficult to close once I have my boards in there because you have to push the top bar all the way down and hold it down to be able to turn the key to lock it. I’m just happy I don’t have to shove the boards in my trunk. I do like that all the parts in this series come with locks and keys. So far no problems. Overall good product.

Click to Enlarge

Click to Enlarge

This rack works great with the four pairs of skis I lugged from Oregon to Alaska. I'm using it on the beef rack cross bars that came with my go fast camper which are very difficult to find mountings for. This one worked great though with a little bit of metal grinding on the bolts that slide into the t-slot of the rack. It locks and unlocks fairly easily (with a little bit of jangling involved), but so far so good!

Click to Enlarge

Love it!!!!!! Great ski rack replacement for older rack. The extended slide is incredible. The eTrailer support helped me pick the model that worked for my car and crossbars. Another wonderful purchase from my go to source for bike/ski or other related products!

Used this last season for the first time. Found it lightweight and very easy to install; the main difficulty was getting front and back carriers aligned on the center of the vehicle as the clasps are offset. It was used to hold 4 sets of skis and did this quite easily. I think 5 sets would be no problem, but six sets might be pushing it especially if you are using wider skis. It is very much worth the extra money to get the extender/slide out option if you stand under 6' tall and have an SUV.

My second Rhino Rack. I use the racks for skiing and fishing pole. I travel a lot and have never had a problem with them. The Installation is simple and can be completed in under 15 minutes. Etrailer was cheaper than amazon, didnt charge for shipping, and I got the rack a few days after ordering. Would totally recommend etrailer.

Click to Enlarge

Product arrived very well packaged and on time. It’s very robust and came with locks installed. It’s also set up for T-bolt rails which I needed. It was also a few dollars less than Amazon. etrailer is great to deal with and their YouTube videos on this and other products are extremely helpful.

Howzit etrailer.com & staff. the rack itself is sturdy and more aero than comparable units. For my 2017 Subaru Crosstrek (OEM) Aero Bars, it was necessary to shim the (rear) lower/leading edge clamp assembly with two 1/8” x 1.5” x 1.5” (EPDM) rubber pads. The bars are shaped like a wing – and these shims helped to level the rear rack with the one in front. Overall - it looks very clean and functional. I might screw on some rubber ends over the ends of the mounting bolt to complete the project. Time to make some turns. Thank you!!

Click to Enlarge

Click to Enlarge

In what universe can you fit 2 snowboards in this thing?! What a waste of money, but the bigger one if you actually need to carry more than one snowboard!

Click to Enlarge