# 1
Dexter E-Z Flex Suspension Kit - Double-Eye Springs - Tandem Axle - 6,000 lbs
Great price. Easy install. The trailer is quiet when the suspension is articulating around tight turns and going over speed bumps. And peace of mind knowing the worn out bushings are gone.
Customer service, response, shipping and ease of doing business are all top of class. The product is solid but kudos to the eTrailer staff for helping me out with a quality issue with one of the shackle assemblies. eTrailer has earned all my future business. It's great piece of mind to know they stand behind the products they sell.
# 2
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 1-1/4" Rear
Good kit with the necessary parts to replace leaf spring suspension. I welded the hangers rather than bolting them. The parts are not coated for the price point so you will need to paint them or they will rust immediately.
# 3
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 7/8" Rear
I am sorry but I can not remember names but I talked with two very helpful ladies and could not have been happier with their assistance. Thanks again, the trailer build is going great.
My 6' x 10' landscape trailer was a homemade by a prior owner. While it was mostly constructed very well, the spring hangers were not correct. The spacing for the springs was also wrong, and it had very little fender clearance. There was also evidence that the spring U-bolts had contacted the frame on occasion. (I do not carry loads anywhere near the 3500# axle rating.) I added an extra set of holes on the front hangers in case the ride height proved to be too much, but I like the way it sits with the stock holes. I don't think I'll be utilizing the extra holes. This kit was just the ticket to increase the suspension travel and fender clearance on my landscape trailer. Now it "sits right"!
# 4
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 7/8" Rear
This is a great kit! It included everything we needed to replace the old, worn-out brackets on our 6'x10' trailer. The directions were helpful and the brackets and hardware are nice and solid. We've had zero issues with the leaf springs (purchased on etrailer.com, also) or the brackets. Would definitely recommend!
Excellent, had everything I needed and more for my trailer. Everything fit well!
# 5
Road Armor Shock Absorbing Equalizer Kit - Tandem Axle - Qty 2
Installed these with the Dexter Bronze Bushings and Lippert AP wet bolt kit. No more clanking and banging from the trailer going down the road and especially making tight turns.
I would give these equalizers 5 stars for performance but due to packaging I will drop them to a 4 star. Our trailer tows considerably better after installing these. After a bump, the trailer smooths out without the chucking that I was used to. Packaging wise, the bolts from one equalizer marred the powder coated finish of the other in transit.
# 6
Dexter Trailer Springs Over-Under Conversion Kit
Our trailer was so low...that it could not make it up a low curb and some driveways - especially when fully loaded. Went with the Dexter axle flip kit. The Dexter bracket and base plate pieces are worth the extra $20-$30 compared to other similar kits - they make fitment easier, eliminate any guesswork on placement, and decrease installation time because of it. Took 2-3 relaxed pace hours for us to do single axle install. Tools required were ratchet/wrench set (13/16 deep socket worked for us for most of the bolts), cheater bar (for working those rusty bolts off), drill, angle grinder (cutter disc for oem u-bolts and leaf spring bolts that are rusted or welded in place, stripper disc for cleaning area around new bracket for welding) welder, floor jack and jack stands. We had to remove the leaf springs, as the wheel mount brackets would not fit through the openings. Was hoping we wouldn’t have to, but it was pretty simple to do. We jacked the trailer up. Removed the wheels. Removed the axle. Cleaned the axle area where new brackets go. Set the height and placement of the new Dexter brackets. We left the OEM brackets on the axle and placed the Dexter ones in the exact same position 180 degrees on the other side. Welded them on. Reinstalled leaf springs. Reinstalled axle, reinstalled wheels. Then voila! We added 6 full inches of height. Super awesome.
Great conversion kit, easy to get the plates lined up perfectly. I welded the new saddles onto the axle and welded the nuts to the bolts so there is zero chance of anything moving. Having the plates held in perfect position while welding made it simple. Solved the "dragging wheels problem" without having to cut off and reweld the fenders (which had been welded without enough clearance to the tires at the factory.)
# 7
Dexter Trailer Springs Over-Under Conversion Kit
The lift worked out perfectly,I had the place where I bought the trailer install them because I didn't have a welder to weld the saddle mounts to the axle and that's a must for a safe installation,also I had the place where I bought the trailer do it because they had the capability to align the axle perfect to the trailer after the installation. The lift added approximately 5 inches to the trailer hight so I could install the off road wheels and tires.The lift didn't affect the handling of the trailer at all.
Jaime at ETrailer was extremely helpful and got my order sent up ups ground since I was having issues using a P.O. Box. My parts arrived quickly and fit perfectly. I installed them last week and my trailer looks so much better and won’t be scraping on my driveway anymore!
What our customers are saying:
"very easy to shop"