# 1
35 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 42" Ground
Replaced the wiring and lights on my 1992 boat trailer. I was able to get everything needed from etrailer. I think Optronics is of the highest quality and recommend both etrailer and Optronics product.
Works very well after re-wiring trailer lights with waterproof distribution box.
# 2
Hopkins 7-Way RV Style Connector with Molded Cable - Trailer End - 8' Long - RV Standard
7 pin connector separated from cable. I was expecting that "Molded Cable" meant that the connector was fused to the cable insulation but instead, the two separated almost immediately after I installed it. It still works fine as the wires are connected securely inside the connector but with the outer covering pulled out like this, I don't think it will last very long.
Çable good but after putting new 7way plug on truck cable wire colors did not match etrailers picture
# 3
Pollak 6-Pole, Round Pin, Trailer Wiring Connector - Trailer End
Quick shipping, will order from them again!
Exactly what I needed and It's a great fit
# 4
Pollak Black Plastic, 7-Pole, RV-Style Trailer Connector - Trailer End
Routine trailer maintenance. Absolutely nothing worse than fighting trailer lighting or electric brake issues when traveling.
I installed this connector on my travel trailer. The original connector had become loose and would fall out if not retained by the tab on the bottom of the connector. After a year of usage The Pollack connector still snaps into place and fits tight. Good product.
# 5
7-Way Molded Trailer Wire Connector, 4' Long
When I ordered this harness I thought I was getting a standard 7 way for a conventional trailer with brakes. What I actually got was a harness made for a camper/RV hook up. The wires have all the colors you would expect but all the lights/turn signals are coded into the plug completely different. After spending a good deal of time carefully matching, soldering and heat shrinking all connections to my new trailer harness, I was very dismayed to find only the brakes actually worked. After a bit of research I found a schematics page on the etrailer site and discovered the problem. As this is a molded plug I could not take it apart and just reposition the wires inside the plug. Another full hour or more of rewiring followed and now all is well. The harness itself is of very good quality but was not labeled/identified properly. This could have been prevented if etrailer would clearly label this harness as a camper/RV harness only.
Ordered 1/28 - showed shipped 2/1 with estimated delivery date of 2/6. It had a USPS tracking number that would only show the label was created. Never showed the product moved. After two contacts with customer service I was told they can't track the package until a certain date. I was notified 2/17 my package would be delivered that day. Not sure what contract etrailer has with USPS but I can track a tin of cookies to Pittsburgh, PA I think they can tell me where my $[XX] package of parts is at.
# 6
7-Way Molded Trailer Wire Connector, 6' Long
Only gave 4 stars because it was a bit confusing. I have a lot of auto wiring experience; from car stereos,amplifiers and all manner of accessories. All of the info on etrailer indicated that the color coding didn't match up. So I went into it disregarding the standard color coding, when in fact it was just as it should be.
Good thick rubber and plug works perfectly.
# 7
RoadMaster 6-Wire Connectors - Trailer and Vehicle Ends
Excellent customer service! Thank you, Sheila!
This was easy to install looks great and works excellent. have had on issues with this product my trailer lights are always working and keeping me safe.
# 8
7-Way Molded Trailer Wire Connector - 3' Long
I've had this in use for over a year and they don't build them like they use to. I use this on a gooseneck trailer and the piece of plastic behind the spade connector for the clearance lights and brakes has melted, allowing the spade connector to lose contact with the plug on the pickup. So the lights would cut off in the middle of the night and would have to wiggle the connection till I could fix it. I have an older Hopkins plug and never had this problem. To fix the problem I ended up putting pieces of thin copper wire behind the spade and have done it twice since the plastic melted a 2nd time and once again the trailer clearance lights would quit working. Attached are before and after pictures.
After a year doing its job well.
# 9
20 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 30" Ground
Wiring worked perfect for my project. I replaced the wiring on my 14 foot utility trailer. If I was to do it again I would buy the next length up. I would have liked to have a little extra wiring if I was to ever need it.
Your sales staff is second to none. Keep up the good work. You shipped minutes after I placed my order! Very impressed! Marty
# 10
Hopkins Endurance Quick-Fix Replacement 4-Way Flat Trailer Connector w LED Test Lights - Trailer End
Nice product & good value imo--it's very beefy and appears to be heavy duty---I know these are supposed to be temporary---that said this one replaced a Reese connector connector exact same style w/LEDs that was almost 17 years old before it failed--hopefully this lasts even close to that amount of time--I don't use this trailer daily usually not even weekly---so maybe with commercial trailer use this connector isn't for you..... It's my considered opinion that many of the fails are the result of a lousy install or someone disconnecting by pulling on the harness INSTEAD of grabbing the connector either way this gets an A+ from me
This is perfect. I needed an easy way to change the connector on the trailer I'm working on. It was an old pop up camper with an 8 pin connector mounted on the frame. but I only needed a 4 after rewiring it. So, out with the old and in with the new! Plus it's really easy to connect all the wires. Picture is not of the new connector but of the whole project I'm working on. I've since mounted all the running lights, tail lights etc.
What our customers are saying:
"Received already. Yeow! Perfect fit. Thanks for getting the kit to me so quickly."