Most Popular 4 Flat for 1982 Ford Fiesta

I have now installed the following on my 2017 Wrangler: Brake light relay kit . Hopkins Towed vehicle Tail Light wiring kit. Blue Ox base plate. Blue Ox Patriot Portable RF Braking System. All of this has taken about 3 days of work spread out over a week or so. Overall it went well. Not too many surprises. Crawling around under a car at 71 is a bit of a strain but I'll get over it. I must say that Donna P. has been a wonderful source of great information and has stayed right on top of the process. eTrailer has been a great source for this project. I would recommend you all with no hesitation.

Click to Enlarge

Click to Enlarge

The items I ordered will allow me to adapt my utility trailer for transporting my sea kayaks. Curt and Hopkins are both quality manufacturers. On a shipping note, the box arrived at the Post Office broken wide open. Your shipping folks need to wrap small, heavy, items in bubble wrap. Then stabilize it with foam peanuts. Just putting it in a box then stuffing the box with craft paper does not cut it. Items were not damaged so I am good to go.

This product works as expected. There is not too much to the installation, just plug it in properly and mount the ground wire. I did not find an easy way to mount this to my wife's Odyssey, or to the trailer hitch (item# 75270). Luckily, I do prototype design and manufacturing. So I came up with my own solution. I designed and made my own bracket to mount the 7 pole to the trailer hitch. It works like a charm, and looks great!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

i had to replace these two items as my dear daughter went down our goat path driveway too fast. they replaced the originals from etrailer from the prior year. shipping is timely and customer service actually helps! i wired from battery to controller to hitch myself, and everything fit.

Replaced the wiring and lights on my 1992 boat trailer. I was able to get everything needed from etrailer. I think Optronics is of the highest quality and recommend both etrailer and Optronics product.

Works very well after re-wiring trailer lights with waterproof distribution box.

ETrailer had exactly what I wanted at a fair price. Website was easy to navigate and purchasing was simple. Shipping was fast and I was kept notified right up to when I received my order.

Plugs in easily, shows that pins are producing voltage, and locks in place using the spring loaded door to the 7-pin.

As always,they had what I needed, good price, fast shipping.....and a video about how to use it. My go to place.

This wiring extension will do very nicely. I have a trailer with removable tongue.

I recently had a need for the Hopkins Endurance Quick-Fix Replacement 4-Way Flat Trailer Connector w LED Test Lights - Vehicle End - HM48190 to replace the faulty one on my van. It was easy to find what I needed on the site and the price was comparable to other sites I had visited. I decided to go with etrailer because I had previously ordered the hitch through them. I appreciated the fact that an email was sent out confirming that they received the order as well as a follow-up email telling me that the part was shipped along with providing the tracking number. The installation of the part was easy and took no time to complete. Overall it was a fine experience and if I need to order anything in the future, I will be sure to come back and order from etrailer.

Click to Enlarge

Click to Enlarge

Great product. Easy to install

What can I say, it works. Etrailer is easy to do business with.

SMI Stay in Play Duo installation in 2015 Jeep Wrangler Unlimited – Packaging was great with everything needed included plus extra items for various installation methods of you’re choosing. Upon initial investigation and survey, everything except the CD Information pack was accounted for. No big deal, as I had previously watched 2 different Youtube installations found on the internet. In fact, the internet videos were what I used as my step by step installation process, and the written instructions were only used for concerns where the video may not have been as clear as I had hoped for. Understanding that everyone has their own style and methods for doing this project, I purposely was not in a hurry to rush through it. All in all, I took @ 8 hours to install the Adapter 4 to 6 pole #30637, the EZMount Tow lights Kit, and the Stay in Play Duo Braking System. I choose the EZMount because I didn’t want to mess around with the OEM taillights and wiring. Magnetic lights don’t work so well on composite tops and I didn’t want to stick them to the sides of te Jeep, so I modified the EZ mount to wrap around the thickness of the rear glass hatch on both sides. I added a 2”x 4” pc of Velcro on the inside of the glass hatch and the mating surface of the plastic light housing - to hold the lamps in place until the rear gate was closed. I ran the wire harness on the inside under the trim all the way up to the front and through the grommet in the firewall. The flat 4 wire was routed and secured up to the Adapter 4 pole to 6 pole that I had fastened to the Blue Ox base plate. The actual installation of the SMI unit and assorted parts went rather smoothly. Most difficult issue was the lack of working space in front of the driver’s seat area. Installing the screw that holds the G force controller on the front (the side towards the front of the car) was difficult as it was almost a blind installation due to lack of room. The nut and fender washer used through the fire wall for attaching the air cylinder cable bracket was a challenge to reach - tight fit with not much room for one's hand and arm. Other than that, no big surprises – just a lot of tedious steps to do when you want to be sure that it is being installed properly – take your time and don’t be in a hurry. Once everything was installed – it all worked when I checked the system out. The only thing that may seem a bit odd is that when setting the G force initially, the compressor will shut off while adjusting per instructions. To do this initial adjustment, the wife stepped on the brake in the Motorhome, with the switch “On”. The compressor starts, and the brake is pushed down by the Air Cylinder, at which time I slowly adjusted the G force until the compressor shuts off. I secured the adjusting bolt and I told the wife to take her foot off the brake and then re-apply them. The compressor did not start again and the air cylinder did not apply the brakes in the Jeep. After setting the G force per instructions, the unit didn't turn on when the brakes in the Motorhome were applied - but since we were not moving - all I can assume is that the brake system will function while slowing down once the accelerometer setting (the sensitivity setting on the G force box) has been met. I assume that the sensitivity setting method includes a way to ensure the Jeep brakes are not engaged too frequently and only until needed. This is the only step that is a tad bit confusing without an explanation as to what to expect once the G force sensitivity is set. Lastly, I checked the brake away switch and it turned the compressor on and applied the brakes as expected. Overall - the installation went rather smoothly. Can't wait to see how the product works once we hit the road. I'll check back and provide an update later.

Click to Enlarge

Click to Enlarge

I am very pleased with the products and service provided by etrailer.com. The 4-way Curt trailer hitch wiring connector and Hopkins Adapter for my 2015 Honda Pilot were easy to install with the clear and well illustrated directions. They are performing as advertised with no additional troubleshooting required. The quality suggests that they are durable and will last for at least as long as I own the vehicle. I currently tow boat trailers. The car came with the OEM trailer tow bar (hitch) and basic internal trailer wiring. The etrailer.com parts were just what I needed to complete the package. [I suggest you include a note to install the provided 10A blade fuse in the holder on the S3 harness in the installation instructions]

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Worked perfectly. Unfortunately ran into a deer two months ago and.dont have the vehicle now

E-trailer: they've got what I need at a reasonable price. This is what e-commerce should be!

I received the product after just a few days. I had many technical questions that were answered by a competent service person. The product arrived in great shape and I had reviewed their installation video so installation went very quickly and easy. My 2011 Chevrolet Silverado is equipped with a 7 pole connection so I bought their adapter to convert to flat 4 pole connection. That an the CR-017 led worked very with first try. I also bought the trailer hitch lock at the same time. All products are very easy to use.

Click to Enlarge

I rewired my light bar for my boat trailer with the items I purchased. Before I built the the light bar, every time I used my boat trailer I would waste valuable sailing or fishing time repairing faulty lights. The do not last long when you submerge them in salt water. This light bar now version 3.0 have given little trouble over the years

Click to Enlarge

Click to Enlarge

Great product. Works well when I had a broken connection on my 4 way plug end on my light-up hitch cover I bought from y'all a while back. Always a happy customer. Thanks, George.

Click to Enlarge