What our customers are saying:
Excellent service both on the phone asking for information and the web. Look forward to recieving the item.... Thanks
Donald
Hondo, TX
Videos
for Trailer Bearings Races Seals Caps
Help Articles
Expert Answers
Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…
Hey Barry, sure do! The seal that comes with the #DX87UR bearing kit is a 1.719" ID and 2.565" OD. We offer this seal individually as part #58846.
From the numbers you provided it sounds like you need replacement grease seals. In my research, the grease seals I found with the GS-1719DL number have a 1.72 inside diameter and 2.565 outside diameter. The replacement double lip grease seals you…
You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…
After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…
Hey Eric, so we do have what you need with the replacement cap part #VA55JR but the one you mentioned is smaller so it would not work for you. The cap you need is 4 inch diameter and the one you referenced is 3.75 inch.
Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…
The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…
You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…
A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…
2019 Airstream Accessories
Towing
2019 Airstream Brake Controller
2019 Airstream Front Mount Hitch
2019 Airstream Blind Spot Detection
Performance Accessories
2019 Airstream Suspension Enhancement
2019 Airstream Tire Chains
Vehicle Trim
2019 Airstream Floor Mats
2019 Airstream Vehicle Seat Covers
2019 Airstream Windshield Wiper Blades
2019 Airstream Wheel Cover
RV and Fifth Wheel
2019 Airstream RV Vents
2019 Airstream RV Mattress
2019 Airstream RV Covers
2019 Airstream RV Weight Distribution
2019 Airstream RV Hubs and Drums
2019 Airstream RV Brakes
2019 Airstream RV Bearing
2019 Airstream Trailer Jack
2019 Airstream Spare Tire Cover
2019 Airstream RV Camera
2019 Airstream RV Propane
2019 Airstream RV Interior Lighting
2019 Airstream RV Exterior Lighting
2019 Airstream RV Jack Pads
2019 Airstream RV Jumper
2019 Airstream RV Bike Racks
2019 Airstream RV Antenna and Radio
2019 Airstream RV Air Conditioner
