To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Most hard covers have to be lifted off if you want to haul something tall. The Sentry CT changes that. It uses 3/4" thick aluminum slats wrapped in premium, 5-layer polyester and vinyl fabric, so it’s strong like a hard cover but rolls up in seconds like a soft one. You can open it from either side using the tailgate release cables and secure it with built-in safety straps behind the cab. When rolled up, it stays clear of the rear window and third brake light, letting you load big gear without removing the cover.


A lot of covers sit high and look bulky. This one doesn’t. The 15-degree angled side rails keep the cover just 1/2" above the bed for a sleek, flush fit. That low profile not only looks clean but also cuts down on wind noise and drag, which can help improve fuel economy. The black slats and matte fabric create a fully “blacked out” look that blends in smoothly with the truck’s lines.

Some covers fade or crack after a season in the sun or snow. The Sentry CT’s 5-layer woven polyester and vinyl fabric is tested to handle temperatures from -40°F to 120°F. It blocks UV rays, rain, and road grime while staying flexible through every season. The heavy-duty aluminum slats shield against hail and falling debris, and rubber weather seals keep out dust and water so your cargo stays clean and dry.

Keeping tools or camping gear safe is easier with this setup. The slam latches at the tailgate lock automatically when the cover is closed and the tailgate is locked. Extra mid-bed latches engage at the same time, so you don’t have to crawl into the bed to secure it. Together, the aluminum slats and latching system give much better theft resistance than soft covers that can be cut open.


Getting rails lined up right can be the hardest part of installing a cover. The Sentry CT’s self-leveling side rails square themselves as you tighten the bolt-on clamps, so there’s no guesswork and no drilling. Once the rails are in place, the quick-release guides let you remove or reinstall the cover in seconds without any tools. The inside-mount design keeps stake pockets open for tie-downs or other accessories.




Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
The Sentry and Sentry CT by TruXedo are hard roll up style truck bed covers that feature an extra low profile.The Sentry comes with a leather grain vinyl fabric and the Sentry CT comes with woven matte black fabric. Both feature fabric that is pressure bonded to heavy duty aluminum slats, making Sentry the ultimate in durability and security.Each cover ships with a cover assembly, driver and passenger side rails, and all the hardware necessary to install it on your truck. The only tools necessary are a half inch wrench and scissors.Clean the bulkhead area with alcohol. Adhere the rubber seal to the bulk head, making sure to align the seal with the inside edge of the bulkhead. Trim the seal to sit flush with the bed caps.Position one side rail on the truck bed. Make sure the rail sits level on top of the truck bed.
Slide the rail towards the bulkhead so that the foam seal is compressed about half way. Install a clamp in the center of the rail, using a half inch wrench to tighten.Install the real clamp about 12 inches from the tailgate. To ensure a proper seal, put pressure on top of the rail when tightening. Install the front clamp about 12 inches from the bulkhead. Repeat on the opposite side.Place the cover assembly on the rails at the bulkhead.
Line the screw head on the underside of the cover assembly with the slot in the rail on each side.Slide the header guides towards the rail to secure the rolled cover to the rails. The header guide will click when it is securely fastened.Unroll the cover to the tailgate. Close the tailgate. Then push down on the end of the cover to latch both sides. Secure the hook and loop on both side rails before driving.To open the cover, drop the tailgate and pull down on a release cable.
Lift and roll rear header.To drive with the cover in the open position, both straps must be secured to the restraining straps. To releasee the strap, push the tab up.The installation is now complete.
Ratings & Reviews

Kate F.
11/13/2026
Elvin, that cover looks sharp on your Ram. I can see why you like the cleaner look without the latches sticking out. Hopefully, this one gives you just as many good years as your old BAK cover did. Thanks for the pictures =)

Bryan
8/22/2023
After a year the cover is still looking great and working great. I wish I had purchased one of these when I purchased my truck, as it is nice to be able to securely store stuff in the bed of my truck.

Jenny N.
9/16/2023
There is a lot going on with the cover. Would you be able to send a picture of the cover and the serial number from it.


Gwendolyn Y.
6/18/2025
Thanks for sharing your honest feedback about the cover, Brian. Let us know how it holds up to the rain and the elements when you get to test it out.

Mike L.
8/27/2026
That's not good Edward! I'll get that taken care of for you.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.









Claire H.
6/10/2026
It looks perfect!! Thank you for the glowing review!