To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Heavy equipment like a snowplow can weigh down the front of your vehicle and throw off traction and steering. The Timbren Front Suspension Enhancement System adds up to 2,000 lbs of support to help keep your vehicle level and stable under load. The hollow rubber springs mount in place of your factory bump stops and work with your existing suspension to prevent front-end sag, improve handling, and help keep your headlights aimed where they should be.
Bumpy roads and uneven terrain can wear down your suspension and make the ride harsh. These Aeon hollow rubber springs act as shock absorbers, taking the brunt of bumps and rough roads so you feel less jarring through the cab. The rubber construction cushions light loads while still allowing full suspension movement, helping improve ride comfort and extend the life of your vehicle’s suspension.
When you swerve or make sharp turns, each Timbren spring reacts on its own to support that side of the vehicle. This independent action cuts down on body roll, helping you stay steady through corners, crosswinds, or when carrying off-center loads. The result is more stability and control when the road or load tries to throw you off balance.
Adding front-end support shouldn’t mean a long shop visit. The Timbren system bolts directly onto each frame rail above your front axle using vehicle-specific brackets and included hardware—no drilling required. Once mounted, the springs stay in constant contact with the axle so they’re always ready to cushion and support without any airlines, compressors, or manual adjustments needed.
Each spring’s convoluted hollow design compresses progressively—soft at first for light loads, then firming up as weight increases. That means a smooth ride when lightly loaded and strong resistance when the heavy gear comes out. This built-in adaptability gives you consistent performance whether you’re plowing snow or just rolling down an empty highway.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi everyone. Aiden here with etrailer. Today we're gonna be taking a look at the Timbren Front Suspension Enhancement System. This is going to be an upgraded bump stop for the front end of your vehicle, whether it be a car like the 4Runner here or a motor home. These are gonna come in a variety of different kits and fits with different capacities and help stabilize the front end of your vehicle. Let's check it out.
So why would you be looking for something on the front end of the suspension enhancement side A lot of people are pretty familiar with airbags on the rear axle, and a lot of those suspension enhancement components are used in towing applications or maybe truck beds where you've got really heavy loads in the bed and you need extra support at the back of the vehicle. Now what the front end can do is stabilize that front end, if you do have something like a front mounted hitch, maybe a plow on a truck, or on a larger vehicle or even a smaller vehicle like this, it does help stabilize body roll a lot because these are going to be a lot beefier than the factory suspension and the factory bump stops, that is, and help limit that side to side movement as we're taking turns or driving down in like really windy conditions on the highway. So this will give a significant upgrade for those applications. As far as the construction for these goes it's going to be a hollow Aeon rubber material with a progressive spring rate. Now, what the progressive spring rate means is the more this compresses, the more pressure it has, the more it's going to work at returning the vehicle to its natural position.
So it's just going to resist more and more as it gets further compressed. As for the installation process, this particular one that I've been holding is for the 4Runner, and this one is a very basic kit. It really just has a threaded end with a bolt and a plate on the inside, but this just spreads into a factory weld done on the 4Runner. Very straightforward install. But for all the other different fits and kits, those are gonna have custom brackets and their own hardware that come with it.
So no matter what one you end up going with, if it's a fit for your vehicle, it's going to be custom fit. So the installation should be just a straightforward bolt on process. Now obviously that can vary depending on the kit and what vehicle you're putting it on, especially on the motor home side of things. But for the most part, you should be able to have a very straightforward install process with any of these kits you pick out. And to make sure you find the right kit for you, be sure to enter your vehicle information into our fit guide and use that to narrow down for the custom fit options available for your vehicle.
If you're considering some front suspension enhancement, I do think that these bump stops from Timbren are a really solid option. From the testing we did in installation on our 4Runner, they performed great. They reduced a ton of the body roll and really helped when we're going over speed bumps and just aggressive driving conditions where we need that extra support. Whether you've got a truck with a plow on it, or a motor home that you're trying to reduce body roll on, something like this can be be a huge help and it's a very straightforward solution. But that'll do it for a look at the Timbren Front Suspension Enhancement System Bump Stops. Thanks for watching.
Ratings & Reviews
I like using Etrailer because i can call and talk to a person. These front ones went in pretty easy just like directions said. and they got rid of the bad bumping sound in my front end after hitting a bump. smoothed things right out.
A+++ Excellent product and customer service. Bought both front and rear suspension enhancements and worth it. Highly recommend.
I have a very heavy "Cattle Guard" on the front of my RAM 3500 and this combined with the heavy 4WD and diesel engine the extra support from the Timbren Front Suspension Enhancement System definitely keeps the front suspension from bottoming out.
Installation was not too hard, Install Videos explain all steps in great detail. BumpStops arrived in excellent condition and was delivered in a timely manner
I installed Timbren’s front and rear on my 2020 F53 chassis motorhome. They are by far the best suspension upgrade I have done. I had previously installed Super Steer Trac Bar, Radius Rods and Safe-T-Plus, which had helped, but not as much as I had hoped. The Timbren’s finalized the package and it drives good now.
Easy install, didn't even need the brackets for my application. Really helped with sidesway in the wind and seems to help the front from dipping with extra weight. Haven't tried plowing snow yet but I think they will make a major difference
The timbrens actually did what they were suppose to do. However, once I starter driving out west I notice the timbrens were riding on the axle which cause the speedometer to jump around depending on the road. I would recommend them if you are hauling or towing a camper or RV. I was going to contact etrailer about maybe removing a spacer for one set however the other set came as one unit. The bottom line is the Timbrens does stabilize your load for safe travels. I will be contacting etrailer soon to assist in correcting the problem...Road trip from Idaho,Colorado,Wyoming,and Utah were beautiful... Thank you etrailer
I had a problem with getting front sumo springs relative to the rear sumo springs I purchased earlier; however, the staff at etrailer were very helpful in getting me a suspension enhancement component made by timbren which I just installed. I believe the timbren supports are going to do the job I was looking for and make me just as happy as I am with the rear sumo springs. You will notice from the photos the supports make direct contact; however, the pictures were taken on a unlevel surface and when the truck is on a level surface the direct contact is equal on either side. Also, the timbren supports provide substantially more weight capacity in the event I choose to haul my scooter on the front end of the truck. Thanks again Derek S and etrailer staff I am very pleased with the service, customer relations and professionalism experienced when ordering my parts. Thank you, Bobby (Louisiana).
Ok it’s been a year since I’ve had the springs and I’m impressed. With how easy the install is and what you get out of it these are truly amazing. No more “squishy” feeling when towing my 22fy travel trailer. The ride is a little bumpy but I don’t care. I’m glad I found these.
For me surprisingly easy to install at 67 years old. Had immediate handling improvement and steering control.
Have them on several trucks now and couldn't imagine running snow plows without anymore.
The front Timbren are working very good.The rear not so good
I would say that the product is a bit pricey for what it contains. The secondary bolts came with the wrong sized nuts. Other than that, they work well to support the suspension.
Install was straightforward. Hardest part was getting the old bump stops out. Sway was greatly reduced on the Interstate and the rock and roll by passing semis was greatly reduced. Wish I had bought these sooner!
These bumpstops really work, they stop the front end vibration before it travels through the shocks and springs, for a smooth ride
Pretty pricey but well worth it. Put these all the way around at the same time as new rear leaf springs on our c7500 topkick and it made a huge difference. It's a top heavy bucket truck and it would rock and roll just turning a corner to the point it was downright scary. Now thats greatly reduced. They also smoothed out the ride especially when loaded more than I expected.
Install was simple, perfect fit. Worst part was grinding out the rivet on the old bracket
I haven/t installed them yet. I think I should have gotten a discount for the age of the "box"s the Timbrens were in. May be a credit ,, Brad
Super simple installation that took about 20 minutes. These made a HUGE improvement on steering control and bounce. Driving on the freeway is a breeze. I highly recommend this product.
It good but one side with no bump had to be put spacer but the spacer was flat so the bolt did not have a lot of thread so I grind the spacer a bit so it could stay flush otherwise this might solve the problem of outter tire wear that ford transit has will find out soon
I love these things. They are worth the upfront expense. I have them on two ¾'s, one ½, and a minivan for road trips. This particular set is full-time active up front. I have a 2" leveling kit and I'm in em no matter what. Zero complaints though. Solid performance through all aspects. I don't run any front-end attachments.
I have a 2006 Kodiak 2 wheel drive. Timbrin firmed up the front end to much. There in full contact with the spring. I think it to stuff and I might be removing them. The install was straight forward. Parts are as expected and quality of Timbrin is great. Just not enough cush..
Great ordering, shipping time, cost, and supporting information. We added a snow plow and the product did everything as advertised.
Very easy to install, took about 30 min.
I haven't had a chance to install the plow on my Jeep to see how this works, but installation was super easy (aside from getting the old bolts from the original rubber axle bumpers out).
Installation instructions say to re-use the original hardware, however my box included new bolts which is awesome since the old ones were pretty rounded after getting them off.
Once the old bolts were removed, installation only required a few wrenches and a rubber mallet. Assembling the rubber "spring" to the mounting bracket took a little ingenuity - the bolt that holds them together is JUST short enough that I needed to insert a washer sideways in my socket to be able to push the bolt enough to engage the threads in the bracket, then it was easy.
Mounting the assembled unit to the Jeep was easy - just put the first bolt partially into the frame then slide the unit under the head, then you can adjust the alignment and put in the second bolt. I used the rubber mallet to get the rubber "spring" to sit on top of the axle and align it so that is was directly above the axle. Then just tightened the bolts, and done.
I used 1 box end wrench and the rest sockets. The first bolt that goes in sits just above the round flange on the bracket so a socket won't fit. The second bolt is easily secured using a socket.
I hope this gives my 1993 Wrangler YJ Jeep the extra strength to support my plow - I am taking the plow off of another Jeep (same basic model) which had leaf springs that got SQUASHED and actually reversed (frowning face rather than happy face) so I'm hoping these suspension enhancers will prevent this from happening.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.