Best 2021 Buick Enclave Vehicle Heaters

Shipping was very fast (2 days) from Florida to Boise.. I have not installed the block heater yet. I'm driving home to Alaska soon and I'll have my mechanic install it there. Required in Alaska for even for gas engines

80% perfect fit! The only thing missing is 90 degree angle for the power cord at the heater(like GM original) also the power cord is not long enough for 2017 Canyon! Otherwise excellent for the price!

Bon achat, j'ai fait l'installation moi même sur un corolla 2016, j'ai nettoyer le trou et j'ai ajouter de la pâte Heat sink compound et j'ai placer le Kat's Heater avec le câble électrique qui était juste assez long pour sortir de la grille. Je l'ai essayer pendant 35 minutes à -17C et il a donner de bon résultat. Cet hivers je vais travailler plus au nord ou il y aura des -40 C et je pourrai vraiment faire un bon test pour voir si il est vraiment efficace. je ferai un autre commentaire pour le verdict.

DO NOT BUY for an early 2nd generation Tacoma (~2005-2011). Fitment and product quality are horrific. As other reviewers have mentioned for these specific vehicles, you have to grind down a side of the metal, removing approx 3/100s of an inch. Annoying, but not a huge deal. After clearancing, the heater cartridge fits right into the designated hole in the block. The bigger issue is that the electrical plug slips right out of the end of the cartridge if you so much as blow on it. The clip designed to hold it all together and secure it into the truck is worthless- it is prone to popping right off of the orange section where it attaches and/or slipping off of its "notch" on the truck. All the bending/adjusting in the world could not make it work. Significant potential fire hazard if the orange plug slips off the cartridge and you plug it into 120V power without realizing this. Extremely disappointed.

Product was great, came as described. Easy to install. Cord was longer than original so it didn't need an extension , so that was perfect.

excellent for farm tractors; use on perkins diesels ,and simpson diesels; just installed and is working fine! a good one should last 20 years; the one I replaced (for a tractor from a tractor supply house lasted less than 2 YEARS, the one before had gone the 20 years) your block heater has a heavy duty cord and the threaded cuff lock down nut on the sender was an all time first for me, thanks. To use this kit 11409 your must already have the block bushing or the bushing for a block heater for this kit will be # 11461b and about $7.00. Noticed your were in SPRINGFIELD TN; I farm in Tn and Ky. good for you. thanks again. TERRY FITZPATRICK, Austin, Ky

Great product. Good quality I can rely on. Needed installation instructions and should’ve came with Teflon.

Have not installed yet, but looks well designed and should work as advertised. This will be replacing a factory injection system on an old IH D260 tractor. I have been able to order and receive overnight a bottle of ether from NAPA.

Easy to install, but the heater cord passes to close of the exhaust manifold, they should provide a heat shield in the kit. Excellent product.

Looks just like what I ordered, shipping was prompt. Seems to be just what I need but it isn't installed yet.

The product wasn't a proper fit at all for the vehicle. I had to modify it by cutting the thickness on the plug end with a hacksaw, to go past the engine case edge. Created a flat spot. Otherwise it wouldn't insert properly into the cavity in the engine. It would have to be all one diameter if designed properly. Not sized or designed well. Now that it's installed it seems to work ok.

2015 Hyundai Sonata 2.4 install. Have to remove air intake, very tight to get it in just enough space. Had to trim a little bit to make it fit but nothing ever fits perfect. Picture say it all.