Most Popular Ultra-Fab Products for 2020 Chevrolet Traverse

Installed easily and they function as designed as well. They look cleaner than the factory stabilizers as well. I also like that they use a 3/4" socket to go adjust and not a special tool like other brands.

Definitely a heavier duty version of our campers stock stabilizers. They bolted right up to the brackets and glad we have new stabilizers. I hope the paint lasts on these as that seems to be an issue with the other, cheaper stabilizers. Time will tell.

My order arrived soaking wet box torn up and mashed. Light switch in side fox was destroyed by king pin stand. Not sure why anyone would place a fragile items in with heavy steel components.

Made in the USA, decent effective range, quality construction. What more could someone want? That said, this is heavy so eTrailer shipped it via UPS. UPS destroyed the package, taped it up, and then proceeded to destroy it again. Luckily, I was only missing one small piece of hardware that is easily sourced locally. Keep that in mind if UPS destroys packages in your area.

Installed easily and they function as designed as well. They look cleaner than the factory stabilizers as well. I also like that they use a 3/4" socket to go adjust and not a special tool like other brands.

Didn’t last 3 months the end came off and screw mess up where the jack don’t work anymore

These Jack's made both building and positioning my teardrop onto the trailer bed easier. At campsites they easily level the trailer. So yes I'm happy.

Click to Enlarge

we are using these stabilizers for supporting our offloaded truck camper (adventurer 910db) where we reside full-time ... they are very easy to use, provide excellent support for the truck camper and have eliminated 98% of wobble ... the support structure includes jack pads, e-trailer stabilizer, 2x6 pressure treated lumber, 4x8 3/4 inch pressure treated plywood

Click to Enlarge

The Product appears to be what I need to add extra support to my toy haulers doors. Not impressed with the shipping company, it was a miracle that the 2 items stayed inside of the box. The attached picture shows you how they arrived today.

Click to Enlarge

I recently purchased a 1/5 wheel travel trailer with 5 slides. It was recommended that I should put slide supports under the bigger slides. After researching, I decided the Ultra-Fabs would do the job. I received them on Thursday and installed 2 sets that afternoon. I followed the guidelines and set them in less than 30 minutes. Friday afternoon I installed the rest. I know they did a good job because my wife's first comment was "the trailer doesn't bounce when you walk across the floor". That was the best test. She didn't know what I was doing under the trailer. They were easy to install, 1 plastic leveling block, the support, and a short level. Set the block under the slid rail at the outermost end, hold the support on it and pull the top up until it touches the rail. Holding the top against the rail with the ears on the sides of the rail. With 1 hand, push the white button and slide the lock ring down against the bottom housing and release the button. Plumb the bottom housing with the level. Give the lock ring 1 good turn after it is snug and you are finished.

Installed easily and they function as designed as well. They look cleaner than the factory stabilizers as well. I also like that they use a 3/4" socket to go adjust and not a special tool like other brands.

Replacement jack fit and worked perfectly Fast delivery

Finally got around to installing my PT II Stabilizers 30" front and rear of our 26' Surveyor. Pre - assembled them to make sure they went together ok. Luckily I had two sources for power front & rear which made wiring easy, I used a Buss block to make all positive connections, grounds straight to frame, soldered all connections and heat srinked to seal. Using the 3/8" self tappers was fun.Well got it all together and all works well makes trailer very stable, don't have to worry about scissor jacks collapsing anymore.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It looks like a great product am anxious to install them. I have a symbol of them in my garage and I have one with a really crooked foot. The bolt hole on the retracting arm was drilled in the wrong place so it is totally crooked, not a deal breaker though. I’m sure the are more than Adequate

Click to Enlarge