Most Popular Track Mount for 2017 Honda Pilot

My OldTown Sportsman PDL120 was shifting around to much in very windy conditions. I bought the large Yakima kayak saddles/supports from etrailer.

Click to Enlarge

I recently purchased the Rhino rack below with these boat supports: Rhino-Rack Nautic 581 Rear Loading Kayak Carrier - Saddle Style - Rear Loading - Channel Mount Item # RR581 Also, I attached a Yakima Jaylow kayak carrier, all to a 2019 Toyota Highlander Hybrid. On the 54 inch aero bars, I was able to carry a Hobie Compass Duo kayak (35" beam, carried flat on the Rhino pads) and West Marine Pompano 120 (28" beam, propped up as shown on the Jaylow racks). To have enough width, the Jaylows and the Rhino pads are mounted as far out as they can go, and the straps are looped back under the rack pillars on the car. The bow and stern were secured with hood loops on each side (front diagonal straps on the Hobie), on the front placed under the hood where shown (this is the only place I could find a good metal-metal contact under the hood, and no electronics in the way), and in the back, tucked under the rear door. We did a 500 mile round trip to the beach and back, with no problems at all with the mounts. Little noise, no movement. My only recommendation is to figure out some kind of load assist for the large tandem kayak, to make it easier if one of the folks loading is under 5'8" in height or so. We worked it out, but only after a few failed attempts (especially when the boat is wet, and loaders are tired). Carol C at etrailer provided thoughtful, expert, and knowledgeable tech support for our purchase. Many thanks!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Must have for a heavy kayak, and/or for taller vehicles. I installed it on Thule areoblade 54cm on a 2018 Honda Pilot. It fits but barely. I would probably recommend 60cm ars if you want to pair it with another Hullavator. Installation note: in order to meet the 4" clearance from the footpod of the rack, I had to install the bars slightly asymmetrical (they stick more on one side of the vehicle than the other). Not enough that it is noticeable. With the 54cm bars, I can pair the hullavator with a Yakima Jaylow, or a Yakima 16 cu in roofbox. I am also able to carry a fishing kayak that is 35" wide but it's tight (the carrier is rated for 36"). A couple of usage tips for what it is worth: - when you lower the boat, make sure to keep the boat level (don't lower one side more than the other). Failing to do so may result in contact between the boat and the car. Don't forget to fold your side mirror too. - When you strap the boat, I find it useful to strap one side lightly, strap the other side, and then tighten things down. It ensures the boat seats properly on the cradles. If I tighten things right off the bat, and the boat isn't perfectly seating on the cradles, I get an issue locking the once the boat is flat on the roof (not sure if that makes any sense, but if you run into the issue, you will know what I mean). - Once setup, it takes less than 5min total to put the cradles in or off the bars (i.e. if you need to park in a garage and clearance is an issue). I hope this helps. In any case, this is an awesome rack.

Bought a pair of these to go on 59" rhino rack bars on our Outback Wilderness and am really pleased. I left the bars full width - they are not a head banger on the car - and mounted the Hullavators as far outboard as possible which means the kayaks clear the side of the car and wing mirrors without folding them in. I did have to modify one Hullavator to make the Hobie Lynx fit (36" wide Lynx = 36" max Hullavator width)

Click to Enlarge

Click to Enlarge