Replacement Kwikee 32 Series Step Recommendation for 1990 Fleetwood Southwind

Question

Question:

I have a 1990 Fleetwood southwind the current steps are a kwikee # 3258 w/ a 8inch rise and 9inch run steps are 11inch deep with a 8inch x 22 mounting Am I correct in ing model # LC372261 as a replacement?

asked by: Dennis J

0

Expert Reply:

Since what you have currently on your 1990 Fleetwood Southwind is a Kwikee 32 step the Lippert Kwikee 32 powered step part # LC372261 that you referenced would be the correct step for you to use.

expert reply by: Jameson C

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 4

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 5

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 6

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 7

There is only one option to replace a Lippert, which is now Curt, Turning Point. You will want the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box item #GY48GR. As far as make and model goes. 5th wheel trailer pin boxes are not model…

view full answer...

Answer 8

With a 2022 F350 short bed, hitting the top of the bed rails should not be an issue with most campers. Turning clearance however, will certainly be a factor. That is one advantage of the Andersen Ultimate hitch #AM3200, as it provides a 9"…

view full answer...

Answer 9

The best way to prevent any clearance issues with your 2022 KZ Durango Gold G356RLQ and your 2020 Chevrolet Silverado 2500 with 6-1/2' bed and factory puck system is by using the Demco Autoslide 5th Wheel Hitch #DM79GV. This hitch slides back and…

view full answer...

Answer 10

Hello Shane, Great question, and I am going to need you pin box number to ensure we are getting you the right part number. If you are unsure of your pin box number, please feel free to send me the information off of the sticker on your current Pin…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Replacement Kwikee 32 Series Step Recommendation for 1990 Fleetwood Southwind

Product Page this Question was Asked From

Continue Researching