Custom Fit Roof Rack Kit With Y00221 | Y00429 | Y53TR
Item # Y62EB
Our Price: $688.80
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
- All Info
- Reviews (143)
- Q & A (0)
- Videos (51)
- Photos
Yakima Roof Rack - Y62EB
- Aero Bars
- Crossbars
- 60 Inch Bar Space
- Yakima
- Silver
- Overhang
- 2 Bars
Extremely quiet, aerodynamic crossbars attach to Yakima towers to create a stylish roof rack for your vehicle. Rubber strips in T-slots push down to load carriers or accessories - no need to trim. Full-length aluminum bars maximize carrying capacity.
Features:
Yakima 60" JetStream MD - Silver:- Quiet, low-profile crossbars let you build an aftermarket roof rack for your vehicle
- Pair with Yakima towers and a fit kit to create a complete roof rack
- Asymmetrical JetFlow shape creates an extremely aerodynamic roof rack system
- Built-in WindRidges help control air flow over bars to dramatically reduce wind noise and vibration
- Aero-style bars reduce drag to help maintain fuel efficiency
- Full-length design maximizes space for carriers and accessories
- Versatile crossbars accommodate accessories that mount in the T-slots or clamp around the bars
- Works with most universal-mount bike, water, snow, and cargo carriers
- Rubber SmartFill strips in T-slots allow for easy installation of channel-mounted accessories
- Simply push down on the SmartFill strips to slide in accessories - no trimming required
- Bottom channels allow for easy installation on Yakima towers
- Fit BaseLine, RidgeLine, SkyLine, and TimberLine towers
- Etched measurements on bottoms of bars help center rack on your roof
- Lightweight aluminum bars are durable and rustproof
- Internal JetTruss extrusions provide exceptional bar strength
- Clear anodized alloy finish is corrosion resistant
Yakima Landing Pad 1 (Set of 2):
- Provide mounting point for Yakima SkyLine and Control Towers
- Fit vehicles with C-shaped factory rack tracks
- Attach to factory tracks with anchor plates and screws
- Include snap-on covers for protection when Towers are not in place
Yakima SkyLine Towers (4-pack) (w/new covers):
- 4 Heavy-duty towers mount Yakima crossbars to your vehicle with fixed mounting points, flush side rails, or tracks
- Pair with 2 Yakima crossbars and Landing Pads to create a complete roof rack
- Tower pitch can be adjusted 6 degrees forward and 6 degrees backward to level your crossbars
- Versatile BarBeds are curved to accommodate the elliptical shape of Yakima CoreBar and JetStream crossbars
- Also fit RoundBar crossbars with adapter
- Easy, tool-free installation - just drop tower onto Landing Pad and close the cover
- Included torque tool clicks 3 times when crossbar is tightened to tower - eliminates fear of under- or over-tightening
- Lockable with Yakima Same Key System (SKS) lock cores (Y07204 - sold separately)
- Weather-resistant die-cast aluminum, stainless steel, glass-reinforced plastic, and elastomer construction
8000221 Landing Pad 1 for Yakima Control or Sky Line Towers
8000429 Yakima Jet Stream Cross Bars - Aluminum - 60" Long - Qty 2 - Silver
8000163 Yakima Timber Line Roof Rack Towers for CoreBar, JetStream, and RoundBar Cross Bars - Raised Side Rails - Qty 2
Replaces 8000148
Video of Custom Fit Roof Rack Kit With Y00221 | Y00429 | Y53TR
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Yakima Crossbars SkyLine Towers Review
Hey everyone, it's Evangeline here at etrailer and today we'll be taking a look at our Yakima SkyLine towers. These are designed for your fixed mounting points, your flush rails, or your track systems. So if the roof of your vehicle looks like this, you probably need these. If you wanna carry around roof mounted accessories like kayaks or ladders or maybe you need to bring a Christmas tree home, you first need a roof rack system. Now this is gonna be the Yakima SkyLine towers for those vehicles that specifically require a custom fit kit for their fixed mounting points. Now if your vehicle does not look like this you might have a naked roof or raised rails.
That's why it's very important before anything to use our fit guide here at etrailer.com. Put your year, make model and then find the right fit for you. And if this is one of them let's take a look at how it works. Etrailer.com also helps you get the full kit for your vehicle because the skyline towers don't work alone you also need the appropriate crossbars as well as the correct fit kit or landing pads for you. But with this, you get a low profile roof rack so it doesn't stick too high up.
You get a heavy duty weight capacity since this is an aluminum roof rack. So usually they have 165 pounds capacity, depends on the vehicle, and you have this very sturdy but also very custom fit kit for your vehicle. That way, no matter what you put on it within reason and wherever you go, you know it's gonna stay there. But my favorite feature about this roof rack is the door design. So you pinch on the door to open it and that's it.
Just like that, you can lift the whole roof rack off of your roof. When you need to install it, you just pop it right back on. So the height of the tower is about 3 1/2" from your fixed mounting point to the top of the tower. The actual height can change depending on what crossbars you have and what rails you have, but compared to a lot of the other flush mounted crossbars and roof racks, it's just very low to the roof. Now with this style of a rack though, you are limited to the fixed mounting points or the flush rails of your vehicle.
So wherever they are, that's how much crossbar spread you get. For example, ours is set to 28" apart. On the other hand, if you have an aggressive tilt to your roof, you can actually adjust this up to six degrees forward or six degrees backward to help even out the playing field. Now I like to leave my roof rack on my vehicle and Yakima is pretty known for its durability. So the SkyLine towers are made of glass reinforced plastic, aluminum, stainless steel and elastomer. So all that is combined to help them stay strong even if you leave them on all day, all year. But if you do need to take off your roof rack you also have a feature to make it more low profile. Start by flipping both doors open and then you can lift the roof rack up and off of your roof. This way you can store it inside of your garage or in your house. You can leave your base on your roof rails. All you need to do is cover them with the included cover and that's it. You're done. The covered bases sit about 2" high up off of your fixed mounting point and makes for a much more low profile look. Your towers will have everything you need to install them which really is just one tool. And your fit kit has the hardware needed to undo the factory mounting points on your vehicle or for your track system if that's what you have. Now, that install process is extremely simple. Let's take a look at it. So these are what your towers look like when they are not on your roof. So they come all assembled in the box. All you need to do is get the appropriate landing pads for your vehicle. These landing pads can look different depending on your car and that's why it's very important to use our fit guide to get the right fit for you. You have four towers as well as the torque tool. And depending on your crossbars, you will also get a separate adapter to be used with those specific bars. With your landing pad kits, you'll get a part that fits your specific vehicle. You will get the hardware needed to install that part and you will have the base as well as the base cover. So if the towers are not on your vehicle you could just cover that base pad and take the cover off to install the tower. Here's an example of how the landing pad can be used depending on your cars. So you have a factory mounting point in this specific flush rail. So the pad goes over that hole and then you're gonna get your base which goes on top of that pad. And then you have a bolt with split washer and flat washer which is used to tighten down those two pieces to your car. The torque tool for your towers comes in handy whenever you're tightening down those bolts because it has a setting for tension. Once you get enough tension, it automatically clicks and prevents you from over tightening. Now to set up your tower for your crossbars there's different adaptor pieces. We're using the one for the JetStream crossbars. So we start by pushing in this plate into the tower. So you are gonna hear some clicks and that's how you know it's secure. Now we're gonna open up the tower door. So this involves pinching the door and pulling. Be careful because if you slide your fingers forward it doesn't feel as good. But with the door open, you can then loosen this bolt up front. It says to do it eight times. I just go until the bolt underneath is visible so you can see underneath what I mean. Notice how you have this little bolt head hiding around. You're gonna try to get at it with the tool. You can see how I do have access. That means as we flip this tower back over I can put this plate up top and then I can tighten down and thread onto that plate. With adapter and plate, this can now slide into your crossbar. For other adapters, they're designed to slide over or around your crossbar. With this specific style, I do recommend for the initial slide making sure that this is loose, but after that even if you have it fully tightened down you'll still be able to slowly adjust it on the crossbar. So with the towers on you're then ready to put this onto your roof. Now what I do is I just kind of roughly measure how far apart our landing pads are and that's when I can measure on the towers the distance apart they roughly need to be, in my case, 43 1/2. You could be off by 1/2" or so 'cause you can still move them. Also, supposedly this is when you put the rubber pieces inside of your crossbars. I do that after I've already installed them onto the roof. I take them back off and then I push them in so that I know exactly where the towers will be sitting. Make sure your towers are torqued down at their bottom bolt. Do that for both sides before installing. This is a lot easier with a friend on the other side but still doable with one person. So leave those doors open so that you can gently place them onto your roof. The bottom bracket with the door open fits onto your base so see how that just pushes into place. And then to secure it, just push that door close and you've got a sturdy fit. If you're using Yakima same key system lock cores, this is a time to switch them out on your towers. But other than that, just double check that all the towers are strong and secure and everything is sturdy. And that's it for the install of your roof rack. That right there was a look at the Yakima SkyLine towers for your Yakima crossbars for when you have vehicles that have fixed mounting points, flush rails or track systems.
Customer Reviews
Custom Fit Roof Rack Kit With Y00221 | Y00429 | Y53TR - Y62EB
Average Customer Rating: 4.9 out of 5 stars (143 Customer Reviews)
Extremely quiet, aerodynamic crossbars attach to Yakima towers to create a stylish roof rack for your vehicle. Rubber strips in T-slots push down to load carriers or accessories - no need to trim. Full-length aluminum bars maximize carrying capacity.by: Eric 05/13/2024
Fit our Subaru Forester perfectly. Install was a breeze. For the money I wish they came with the core locks.
by: Bryan03/27/2024
Very nice and heavy duty. They don’t look too fragile on a lifted truck with oversized tires.
by: John11/16/2023
Very nice quality towers. Very heavy duty! They have a cool "snap" on / off mechanism for quick removal and installation.
by: Frank P.03/06/2016
Fit good with the OE track on roof. I like the new covers they supplied with the mounts.
by: Hurtlocker08/12/2023
Strong, Solid Bars, Super Light, and really easy to install!
by: Nelson06/26/2023
Ford
It was what it was advertised and fit perfectly on my 2023 Ford Maverick
by: Rob04/19/2023
Honestly, I love etrailer. I love the expert help that you all provide. It's clear by the 1 year follow-ups that you care more about the relationships with your customers then just making a sale. Your service is friendly, informative and fast. I always come here first to look for my next purchase. Thanks again-Rob.
by: William02/28/2024
You guys provide great products and excellent customer service.
Thanks
by: Layne 02/11/2024
These crossbars were easy to install and adjust. Be sure to get all the pieces you need. There is no mention of the Landing Pads necessary to use these.
by: Aaron 02/10/2024
Perfect match
by: Pat G08/29/2013
Great first experience dealing with you guys! Shipped fast, and was a faster install. You gave me the right parts and it went together in a flash.
Will definitely be doing business with you all again.
by: Ric 07/22/2023
Honestly went back to etrailer after buying something i couldnt find on the big A before because their support was so good and delivery speed was soo fast.
by: William 01/11/2024
Shipment received, as ordered! Thanks again to Bryce D., for assistance.
by: Michael01/22/2023
Yakima SkyLine Towers are well-designed and well-executed. They easily fit into the Yakima Landing Pads and form a tight fit when closed. And they also fit nicely into the Yakima JetStream Crossbars when following the Yakima instruction manual and various YouTube videos. I did run into a snag at first where I found the rubber seal on one SkyLine Tower getting caught on the JetStream Crossbar track, but after that I was careful not to let that happen with the other towers.
I find the appearance of the Yakima SkyLine Towers to match their level of quality in materials and design.
by: Dan 11/06/2023
Great company! Fast delivery.
by: Jerry 07/29/2023
I have ordered several times from Etrailer and have always received efficient, timely and reasonable shipped items. Did not use customer service with this order but it has always been good.
by: Doug02/16/2022
First trip with the new rail system and it looks like it worked out just fine. Thanks to both of you and Kimberly for all of your help and follow up I do appreciate it.
by: See11/03/2022
with so many variables having someone that could sort through all them was very helpful Thanks etrailer
by: Carlos M.12/26/2018
2016 Ford F-150
Bought these Landing Pad 1 bases to use with Yakima tracks on a Leer camper shell on my 2016 F150. The bases are very easy to install and worked perfect with my Control towers. Great quality as expected with Yakima.
by: Mickey H03/27/2017
I've been using the roof rack a lot in the last year for recreation and for work. They give me confidence that the load will stay put, and arrive safely. I also take them off frequently since they hum happily at highway speeds, so I'm happy that the bars are easy to lock on or take off.
by: Philip 05/29/2023
These really look so much better then the factory racks! Easy to install. Easy to order! Great product!
by: Hogan06/09/2023
I’ve placed 2 separate orders with etrailer in the last 6 weeks. Their service, response, pricing and follow-through have been terrific each time. I will use them every chance I get.
by: John02/18/2022
These will mount to the rhino rack tracks so I could use my Yakima control towers and rack.
by: Luke 07/24/2023
Works as described
by: Steve K.04/23/2019
Easy to install thanks to the etrailer video. I have used the rack system on many long distance trips including driving from South Carolina to Yellowstone.
25
649
Show More Reviews
See what our Experts say about this Yakima Roof Rack
- What Roof Rack Do You Recommend for a 2007 Honda Element SC?Absolutely! For a great roof rack system that will fit your SC version of the 2007 Honda Element, I recommend the following parts: - Yakima JetStream Crossbars - Aluminum - Silver - 60" Long - Qty 2 # Y00429 - SkyLine Towers for Yakima Crossbars - Fixed Mounting Points, Flush Rails, and Track Systems - Qty 4 # Y53TR - Landing Pad 9 for Yakima SkyLine and Control Towers - Qty 4 # Y00229 - (Optional for extra security) Yakima Same Key System (SKS) Lock Cores (QTY 2) # Y07202 With the above...
view full answer... - Recommended Roof Rack for a 2024 Nissan Pathfinder w/ Raised Rails I would be happy to! To add a Yakima roof rack to your 2024 Nissan Pathfinder you will need the following parts: Yakima JetStream Crossbars - Aluminum - 60" Long - Qty 2 item # Y00426 for Black or item # Y00429 for Silver TimberLine Towers for Yakima Crossbars - Raised, Factory Side Rails - Qty 4 item # Y33TR This aero bar roof rack system has a 165 lbs capacity. I recommend adding the Yakima Same Key System item # Y07204 to prevent theft. A great perk of Yakima's products is you can...
view full answer... - Recommended Roof Rack for a 2024 Acura RDX w/ a Naked Roof Congrats on the new SUV! Yes, we do have a way to attach a roof rack to your 2024 Acura RDX even though you do not have roof rails. It is the roof rack by Yakima and it includes the following parts: Yakima JetStream Crossbars - Aluminum - 60" Long - Qty 2 item # Y00426 for Black or item # Y00429 for Silver BaseLine Towers for Yakima Crossbars - Naked Roofs - Qty 4 item # Y28TR BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2 item # Y06174 BaseClip Fit Kit for Yakima BaseLine...
view full answer... - Recommended Roof Rack for a 2024 Acura MDX w/ No Roof Rails Yes, we do! To add a roof rack to your 2024 Acura MDX with a naked roof you will need the following parts: Yakima JetStream Crossbars - Aluminum - 60" Long - Qty 2 item # Y00426 for Black or item # Y00429 for Silver BaseLine Towers for Yakima Crossbars - Naked Roofs - Qty 4 item # Y28TR BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2 item # Y06163 BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2 item # Y06178 This aero bar roof rack system has a 165 lbs capacity....
view full answer... - Yakima Jetstream Roof Rack that Fits 2024 Ford Escape with Naked RoofYes, we do have a Yakima Jetstream roof rack that fits your 2024 Ford Escape with the part numbers # Y00429, # Y28TR, # Y06137, # Y06152. We recently installed all of the roof racks we offer and everyone agreed the Jetstream was the nicest and easiest to install.
view full answer... - Will a Yakima Roof Rack System Fit My 2020 Toyota Highlander LE?I confirmed with Yakima that mounting points that are on your bare roof of your 2020 Toyota Highlander will fit a roof rack system. After you pop off the tab that covers the mounting points, there is a screw that you will use to attach a roof rack system. I went ahead and attached a video that shows how you would attach a Yakima roof rack system on the 2020 Toyota Highlander. For the parts you need for that setup, you will need the following parts: - Yakima JetStream Crossbars - Aluminum...
view full answer... - Recommended Roof Rack for a 2023 GMC Yukon XLTo add a roof rack to your 2023 GMC Yukon XL, you will want the roof rack by Yakima which includes the following parts: Yakima JetStream Crossbars - Aluminum - 60" Long - Qty 2 item # Y00426 Black or item # Y00429 in Silver SightLine Towers for Yakima Crossbars - Flush Side Rails - Qty 4 item # Y64AR SightClip Fit Kit for Yakima SightLine and RidgeLine Roof Rack Towers item # Y44UV I have attached a couple of pictures below that will show you what this roof rack looks like and how to...
view full answer...
- Roof Cross Bars That Fit A 2015 Chevrolet Silverado 1500 With An A.R.E MX Bed CapTo install a roof rack on your A.R.E MX Bed Cap on your 2015 Chevrolet Silverado 1500, you're going to need to install a set of tracks like: -Yakima Tracks for Roof Racks # Y01126 for 42" long tracks, -Yakima Tracks for Roof Racks # Y01127 for 54" long tracks, or, -Yakima Tracks for Roof Racks # Y01135 for 60" long tracks. From here you'll need an actual set of crossbars like the: -Yakima JetStream Crossbars # Y00429, with the BaseLine Towers for Yakima Crossbars # Y28TR, and the Landing...
view full answer... - Roof Rack Recommendation for 2021 Toyota Highlander with Naked RoofHey Ronnie, I attached a link to this page that shows all of the roof racks that are a fit for your 2021 Toyota Highlander with a naked roof but my favorite option is the Yakima Jetstream part # Y00429, # Y28TR, # Y06153, # Y06132 as we had chance to install all of the racks we carry and we all agreed the Yakima racks are the nicest and the easiest to use. This is a through bar design which means the bars are longer than the feet of the rack which is great for if you need max bar space. If...
view full answer... - Yakima Roof Rack for 2018 Honda Odyssey that Can Fit Thule Hullaport XTThe Yakima HD bar is too thick for the Thule Hullaport XT part # TH849000 to attach to so for your 2018 Honda Odyssey you'd be better off with the JetStream roof rack part numbers # Y00429 and # Y33TR.
view full answer... - Roof Rack For A 2017 VW Golf Sportwagen To Use With The Thule HullavatorWe can definitely set you up with a roof rack for your 2017 Volkswagen Golf Sportwagen that is compatible with the Thule Hullavator # TH898. The Hullavator requires the crossbar to overhang past the tower by 4" to 8", so it will be best to use a solid aero bar setup with a slightly longer crossbar. For that I recommend the Yakima Jetstream roof rack. This will consist of the following parts: Yakima TimberLine Towers for Yakima Crossbars # Y33TR Yakima JetStream Crossbars - Aluminum - Silver...
view full answer... - Best Roof Rack For 2024 Kia EV9 With Raised Side RailsThe best roof rack for your 2024 Kia EV9 with raised side rails is from Yakima, and consists of the following part numbers: - Yakima JetStream Crossbars - Silver # Y00429 or Black # Y00426 - TimberLine Towers for Yakima Crossbars # Y33TR I really like the Yakima brand due to how quiet the bars are; they have what are called "WindRidges" on top that control the flow of the air both over and under the bar, which minimizes both vibration of the bar and wind noise. It is also highly durable,...
view full answer... - Square Bar Roof Rack that Fits 2020 Ram 1500 Quad CabThule offers a square bar roof rack that fits your 2020 Ram 1500 quad cab with the part # TH712500, # TH710501, and # TH145199. Then for a square bar roof rack the Thule Portage part # TH819 would work great.
view full answer... - Yakima Crossbar Length For 2022 Lexus GX 460 & HullavatorI checked with Yakima regarding the crossbar length, and they do say 50, which is odd for your 49 inch rails. With that distance between your rails, don't use the 50 inch bars, use the 60 inch long JetStream bars, either Silver # Y00429 or Black # Y00426. The rest of the parts for the Yakima rack on your 2022 Lexus GX 460 remain the same; Towers # Y53TR, Landing Pad 30 # Y25ZR and Lock Cores # Y07204.
view full answer... - How to Determine Correct Roof Rack For 2024 Kia TellurideI'm going to go ahead and respectfully disagree that we're idiots, Paul. I'm confident we can figure out the combination for a roof rack on your 2024 Kia Telluride, and there are three possible options Kia has for your roof - flush-mounted rails, raised side rails, and a bare roof. I made some diagrams below showing test fits on a Kia Telluride with photos from the nice folks at Yakima so you can see the difference (please note these are just test fit photos, and not exactly how the rack...
view full answer...
- Roof Rack for Thule Canyon XT Roof Cargo Basket on 2020 Subaru AscentYour 2020 Subaru Ascent will require a roof rack to carry any cargo basket, including the Thule Canyon XT Roof Cargo Basket # TH859XT. Assuming you have raised side rails that run front to back on your Ascent, here is the roof rack that will work with your Subaru: - Yakima JetStream Crossbars # Y00429 (Silver) or # Y00426 (Black) - TimberLine Towers for Yakima Crossbars # Y33TR As for the paddleboards, there isn't anything designed to carry them in a cargo basket so you can use whatever...
view full answer... - Rooftop Cargo Carrier Recommendation for 2020 Toyota Highlander with Panoramic RoofFor a great option for your 2020 Toyota Highlander with panoramic bare roof, I recommend the Thule Force XT XXL # TH6359B. This box has the largest internal dimensions out of all of our cargo boxes. It also comes with a dual-opening lid that can be accessed from either side of your vehicle. I confirmed that your trunk can fully open with this box mounted on your roof. If you already have crossbars, I recommend measuring your bars to make sure they do not exceed 3-1/2" wide x 1-11/16"...
view full answer... - Yakima Roof Rack that Fits 2019 Honda Passport with Raised RailsSince your 2019 Honda Passport has raised rails the roof rack feet that fit it are the ones that wrap around the bars whereas the flush bar roof styles are the ones that have options that attach directly to it. So for a Yakima there is the Jetstream part number # Y00429 and # Y33TR which is an aero shaped bar setup that wraps around your raised rails. This is a very solid setup that will work great and is no less reliable than any other option.
view full answer... - Roof Rack For 2015 Toyota Highlander For Naked RoofThe video you referenced is for a 2015 Toyota Highlander with flush mounted rails; I checked directly with Thule and they do not have a roof rack fit for a naked roof on a '15 Highlander, just one with those flush mounted rails. So if you want a rack, you'd need a new set up. For that I would go with Yakima, as it is the that is the most similar in quality to a Thule rack. The parts that make up a Yakima roof rack for your 2015 Toyota Highlander are the following: - Yakima JetStream...
view full answer... - Recommended Roof Rack System For 2021 Kia Telluride LX with Naked RoofThe only company at the moment (June 2023) that makes a roof rack system for your 2021 Kia Telluride LX with a naked roof is Yakima, so for a roof rack system you'll need the following components: Crossbars # Y00429 Feet # Y28TR Fit Kits # Y06125 and # Y06165 I'd also recommend adding the locks # Y07204 to secure the roof rack to your roof to deter theft. Out of all of the crossbar options for your vehicle this is by far the best due to the Aero design to cut down on wind noise the most,...
view full answer... - Does Thule Force XT XL Rooftop Cargo Box Fit Yakima Roof Rack on 2023 Acura MDXYes, the Thule Force XT XL # TH6358B will fit very easily on the Yakima roof rack for your 2023 Acura MDX. There won't be any issues with the fit of your cargo box on this rack it will fit perfectly so you can continue to use it. The only thing you need to do is pick the right Yakima rack for your '23 MDX, depending on if it has a bare roof or flush-mounted rails. Bare Roof - Yakima JetStream Crossbars - Silver # Y00429 or Black # Y00426 - BaseLine Towers # Y28TR - BaseClip Fit Kit # Y06163...
view full answer... - Whats The Longest Roof Rack Available For 2023 Toyota Highlander For Thule HullavatorThe longest crossbar that'll work with the flush roof rails on your new 2023 Toyota Highlander Hybrid Platinum is 50" and is the Yakima roof rack system which uses the following parts: Crossbars # Y00429 Towers # Y53TR Landing Pad # Y66VR This will be long enough to use both but as each one weighs over 40lbs, plus the roof rack weighs about 15lbs you'd be overloading your roof with two kayaks and two hullavators as your roof only has a 165lb capacity per Toyota.
view full answer... - Recommended Roof Rack For A 2023 Toyota RAV4 With A Thule Hullavator Hi Cathy, To ensure that you can get the extra extension to mount the Thule Hullavator # TH898 you'll want to go with a Yakima roof rack system. Yakima crossbars run their mounting track the entire length of the crossbar so you can go with ones that are longer than your typical length without worrying if the mounting feet will be able to connect. You'll want the following components: Yakima JetStream Crossbars - Black - 60" Long # Y00426 or silver # Y00429 SkyLine Towers for Yakima Crossbars...
view full answer... - Will Rhino-Rack Crossbars Fit On Yakima BaseLine Towers? The top channel on most crossbars like the Rhino-Rack and Yakima are similar but you should never mix and match towers and crossbars between different manufacturers. Their components are designed to work specifically with each other and your Yakima towers may not work properly with the Rhino-Rack crossbars. Instead you will want to stay with the Yakima crossbars from the list below to ensure they fit together properly and you have a manufacturer who will stand behind the warranty for the...
view full answer... - Which Yakima Landing Pads for 2021 Toyota Highlander to Mount Skyline TowersTo use the Yakima Skyline Towers # Y53TR on your 2021 Toyota Highlander the correct landing pads are the Landing Pad 28 for Skyline and Control Towers # Y66VR.
view full answer... - Roof Rack Recommendation for a 2021 Honda Pilot with Flush Roof RailsWe do have roof rack systems that fit the flush rails on your 2021 Honda Pilot. I recommend using the Yakima JetStream roof rack system because the legs have adjustments in them so that the crossbars sit level with each other. You need the following parts: 50" JetStream Crossbars - Black # Y00425 SkyLine Towers - # Y53TR Landing Pad 19 - # Y00245 Lock Core Kit - # Y07204 (optional) If you let me know what you plan on using the roof rack for I'll be more than happy to make a recommendation...
view full answer... - How to Carry Cargo on 2014 Mercedes Benz E-350 Coupe with 2 DoorsIf you are looking to carry cargo or bike racks on a 2014 Mercedes-Benz E-350 the best option is going to be to install a roof rack because the only hitches available are for a '14 E-350 are for a sedan or wagon. The good news is that you can install a roof rack whether or not you have the Panorama Roof as it will attach to fixed mounting points on your Mercedes. I highly recommend going with a roof rack option from Yakima because it will give your 2014 Mercedes E-350 coupe a roof rack...
view full answer... - Can I Use the 60-Inch Yakima JetStream Crossbars to Use My Hullavator on My 2021 Toyota Highlander?If you are looking at the JetStream crossbar system for your 2021 Toyota Highlander Hybrid with flush rails, you are correct that you need the SkyLine Towers # Y53TR, Landing Pad 28 # Y66VR, and Lock Cores # Y07204. These etrailer part numbers correspond to the Yakima part numbers you mentioned. However, the JetStream Crossbars 8459629 did not come up with a matching etrailer part number. However, if you are looking for 60-inch bars, those are # Y00426. While Yakima recommends 50-inch crossbars...
view full answer... - Thule Kayak Carrier Recommendation for T-Slot Mount on Yakima JetStream Crossbars on 2022 HighlanderIt truly depends on what Thule kayak carrier you wish to use on the Yakima JetStream Crossbars. For example, the Thule DockGlide # TH896 is compatible with the top slots of the JetStream crossbars without any additional nuts. I definitely recommend the DockGlide because it is a saddle-mount style that is much easier to load than the awkward positioning of j-style carriers. In order to have a full JetStream setup of a roof rack on your 2022 Toyota Highlander, it depends on what roof type...
view full answer... - Roof Rack For Thule Tepui Tent on 2018 Jeep Compass TrailhawkIt's always a tough question to answer when you're a company that specializes in roof racks as the liability of the setup could get them in trouble. That being said, it can be done but they are probably concerned with the manufactures weight capacity of the roof on your 2018 Jeep Compass. All I can do is give you the heaviest duty rack and it's up to you to make sure your compass can handle the weight. I would get the Yakima HD bars # Y01156 which are extremely strong. You'll need the...
view full answer... - Best Option To Upgrade Roof Rack On 2018 Subaru OutbackThe best upgraded roof rack we can offer for a 2018 Subaru Outback Wagon would be from Yakima, the JetStream Crossbar System part # Y00425, part # Y53TR, and part # Y00241 in particular is what I recommend. This system would provide you with a 165 lb weight capacity which would be the limit for this vehicle. It would also provide you with longer crossbars as well as those that have channels which will make the roof rack much more versatile.
view full answer... - Roof Rack for a 2018 Subaru WRX to use OEM Subaru AcessoriesI recommend the Yakima Jet Stream kit for your application, based on the shape of the previous bars you had. This kit provides you with aero shaped bars that are very similar to the 2011 Subaru Impreza's factory bars. This rack installs into the fixed points on your roof, however is not compatible if you have a glass roof on your Subaru. The kit consists of: JetStream Crossbars, 50 inches, part # Y00425 SkyLine Towers, part # Y53TR Landing Pad 11 for Yakima Towers, part # Y00233 This...
view full answer... - Selecting a Cargo Carrier for a 2012 Subaru Impreza Sport 5 DoorA good starting point is to refer to your vehicle owners manual to confirm the roof weight bearing capacity. This will ensure that you do not overload the roof. Bear in mind that the weight of the carrier itself, plus the weight of the loaded cargo, will all be borne by the Impreza roof. If your Impreza Sport has factory installed roof side rails (that run front to back) and factory crossbars (that run side to side) then you do not need to add any components to your roof in order to support...
view full answer... - Fit of Yakima Raptor Bike Rack for 2017 Honda Pilot with Factory Side RailsFor your 2017 Honda Pilot with factory flush rails but no loadbars, you can use the Yakima SkyLine Towers for Yakima Crossbars - Fixed Mounting Points, Flush Rails, and Track Systems - Qty 4 # Y53TR, the RoundBar SL Adapter # Y03536, and the landing pads # Y00245. This will allow you to utilize your current round bars and tower locks with no further adaption needed for your Yakima Raptor bike rack. For an aero bar system, you can use the Jetstream Crossbars # Y00425, The Skyline Towers...
view full answer... - Roof Rack for 2018 Jeep Wrangler JL that Can Allow Thule Hullavator Carrier to InstallThe Yakima Jetstream roof rack part numbers # Y00425, # Y53TR, and # Y00226 that you referenced is a confirmed fit for your 2018 Jeep Wrangler JL and it by itself easily has capacity and bar length to carry two of the assisted Thule Hullavator roof racks part # TH898. You'll need to check to make sure the hardtop of your Jeep has the capacity for your two kayaks and the weight of each of the Hullavators as well which weighs right at 40 lbs.
view full answer... - Will There Be Large Overhang With 50" Crossbars On A 2023 Buick Enclave The overall width of a 2023 Buick Enclave (not including the mirrors) is 78.7" so 50" crossbars like the Yakima JetStream Crossbars # Y00425 most likely wouldn't extend past the roof of the vehicle. We don't currently have a picture of them mounted on your specific vehicle, but you can do a bit of measuring to see exactly how far this would stick out. If you have flush mounted rails that run from the front to the back then you can measure across to see the spacing and determine how much...
view full answer... - Do Yakima SkyLine Towers Fit a 2023 Chevrolet Blazer S Using Landing Pad 19Yes, the Landing Pad 19 # Y00245 are compatible with the SkyLine Towers for Yakima Crossbars # Y53TR. This will allow you to mount Yakima crossbars like the Yakima JetStream Crossbars # Y00425 on your 2023 Chevrolet Blazer S.
view full answer... - What Crossbar System Do I Need to Mount a Thule Motion XT # TH629706 to MY 2019 Subaru Outback?For a compatible roof rack system that will work with Thule cargo boxes like the Thule Motion XT Rooftop Cargo Box - 16 cu ft - Black Glossy # TH629706 on your 2019 Subaru Outback Wagon with raised factory rails, I recommend the following parts: - Yakima JetStream Crossbars - Aluminum - Silver - 50" Long - Qty 2 # Y00428 - SkyLine Towers for Yakima Crossbars - Fixed Mounting Points, Flush Rails, and Track Systems - Qty 4 # Y53TR Landing Pad 15 for Yakima SkyLine and Control Towers - Qty...
view full answer... - Fitting a Cargo Box to a 2016 Acura MDXYou have a couple of options for this situation. Prior to any changes, I'd take a minute and get the full clearance that you have on your vehicle. To get this, you'll measure from the center of the front bar to the line where your roof meets the hatch. This is your available clearance, and your roof boxes will need to have a clearance requirement of less than this measurement to fit. You can check the measurement of your Evolution box by measuring from the center of the rear mounting...
view full answer... - How To Use Yakima Round Crossbars on 2018 Tesla Model S with Panoramic RoofI do have an option for you but for the 2018 Tesla Model S you must use the Yakima Skyline Tower part # Y53TR and Landing Pad 22 part # Y00248. Then, in order to use the Round 58" CrossBars for Yakima Roof Rack System part # Y00409 you'll need the Yakima Round Bar Adapters part # Y03536. The Yakima Timberline Towers are not compatible.
view full answer... - Can the Yakima SkyRise Tent Be Used on a 2011 Honda CR-VAccording to the owner's manual for your 2011 Honda CR-V, the roof has a weight capacity of 165 lbs. Therefore, you can use a Yakima SkyRise Tent on your CR-V without any issues as it meets the minimum weight capacity requirement of 165 lbs. The Yakima SkyRise does have a 60 lb weight capacity but since the ladder will support much of the weight, the roof rack/vehicle only needs to be rated for 165 bs. In order to use the Yakima SkyRise on your CR-V you will also need an aftermarket roof...
view full answer... - What do I Need to Carry My Bikes and Gear on the Roof of My 2020 Blazer with a Bare Roof?To get your bikes and gear on your roof you need a roof rack. Yakima makes a cross bar mounting kit to mount to your flat roof # Y00425, # Y53TR, # Y00245. Before loading your bikes and gear on your roof, you need to look in your owners manual for the roof capacity of your Blazer. I recommend the Yakima Front Loader # Y02103 this is a lighter rack which enhances your ability to keep all of your gear on the roof. This is a great single bike rack because there is no contact with the frame...
view full answer... - Parts Needed to Install Yakima Round Crossbars on a 2006 Honda CR-VThe Yakima RailRiders are a very old style of roof rack that hasn't been around in a long enough time that there are no landing pad or any fit info available. If you have a set of round Yakima crossbars like the part # Y00408 you can reuse them but you have to go with the current Yakima towers etc. For that you'd also need the part numbers # Y53TR, # Y03536, and # Y00228.
view full answer... - Can I Fit Four Pair Of J-Style Carriers On Top Of My 2013 GMC Yukon?You could possibly fit four of the # S65148 on your roof but it will be a pain to load majority of your kayaks up there. There is a better solution I found that will be more user friendly. You are going to need a large roof rack bar to accommodate your 4 kayaks. I suggest the Yakima 60" HD Bars # Y01157 and If you have factory side rails you will need the Yakima SkyLine Towers # Y53TR along with the Side Rail Adapter # Y03541 and Landing Pad # Y00221. If you have factory raised rails...
view full answer... - What Roof Rack Can I Use with the Thule Hullavator on My 2022 Toyota Highlander with Flush Rails?I have a great solution for your flush rails on your 2022 Toyota Highlander to use the Hullavator # TH898. Yakima temporarily discontinued the Y00148 because they are updating the feet to fit a wider range of vehicles. Yakima has been changing a lot of fitments lately because of this factor. The landing pads # Y66VR are separate from the Y00148. However, with that being said, Yakima does have a roof rack system that fits your flush rails with a different model of feet. For that system,...
view full answer... - Installation of Yakima Roof Rack on 2019 Jeep Grand Cherokee With Flush Mount RailsAssuming your 2019 Jeep Grand Cherokee has the black and chrome flush-mounted rails that run front to back, you are correct that the roof racks you mentioned do install into the same place the factory bolts are. I have added links to an installation video of the Yakima JetStream roof rack on a Jeep Grand Cherokee with flush mount rails so you can see exactly how the rack installs. The Yakima JetStream (which is shown in the accompanying photo installed on a Jeep Grand Cherokee) consists...
view full answer...
- Roof Rack and Kayak Carrier Recommendation for 2019 Subaru Outback WagonThe roof rack I recommend for your 2019 Subaru Outback Wagon is the Yakima JetStream rack part numbers # Y00425, # Y53TR, and # Y00241 because this rack attaches directly to the factory fixed mounting points on the rails of your roof, because this rack has aero shaped bars that will minimize wind noise and because the rack is well-made and easy to install. Then for a kayak carrier the Yakima JayLow # Y04073 is what I recommend because this rack is padded, can fold down when not in use,...
view full answer... - Roof Rack That Fits 2012 GMC Yukon Denali with Flush Roof RailsOkay so Yakima does offer a roof rack that fits the unique Denali flush rails of your 2012 GMC Yukon with the part numbers # Y00426, # Y53TR, and # Y00246 for their JetStream bar setup. Thule at this time does not have a fit for the Denali versions of your vehicle. The fit kit of this rack does use a channel nut that slips into the channels you mentioned having on the flush bars.
view full answer... - Roof Rack Recommendation for 1983 HiLo 25L Voyager CamperI do have a solution for you but the SportRack Pop-Up Camper Roof Rack # SR1020 won't work because of the 91.5 inch width of your camper. The SportRack Pop-Up Camper Roof Rack # SR1020 works with a maximum width of 85.5 inches which is the only version available. Based on my research, the only other solution is to install a pair of Yakima 60" Tracks # Y01135 (longest available) a few inches inside the edge of your camper's roof along with the Round 86" CrossBars for Yakima Roof-Rack System...
view full answer... - Recommended Track System for Cargo Platform on 2003 Toyota Tacoma with TopperThe Yakima 60" Tracks for Roof Racks # Y01135 will work well on a sheet metal roof. You will want to be as close to the frame weight supports as possible to maximize the weight capacity. It sounds like you want to do a customized fit but I don't recommend running the track between the cab and topper. I'd use two separate tracks that are lined up so there is the ability to remove the topper if ever desired and you won't have the chance of an unsupported tower sitting in the gap between...
view full answer... - Roof Rack Fit Recommendation for ARE Truck TopperThere were versions of the A.R.E. camper shells that had tracks on them already. The factory rails were made by Yakima. For a complete roof rack system on your A.R.E. topper you will need the following parts if you have the rails: 4 of the Yakima Control Towers # Y8890027 2 sets (2ea) Yakima Landing Pad 1 # Y00221 1 set (2ea) Yakima Crossbars: 58 inch bars are # Y00409 66 inch bars are # Y00410 78 inch bars are # Y00411
view full answer... - What Crossbar System Accommodates a Rooftop Tent on My 2017 Honda Accord? For your 2017 Honda Accord with a bare roof without fixed mounting points, the best option is a system that involves drilling. This is because all of the non-drilling options for your vehicle include door jamb clamps that are not recommended for supporting the extra weight associated with a roof top tent setup. Manufacturers strongly discourage this because door jamb clamps setups can buckle and become detached with the weight. With that being said, I recommend the following track system:...
view full answer... - What Parts Are Needed to Use a Roof Top Tent on a CX Truck CapTo use a roof top tent like the Yakima SkyRise HD Tent # Y07437 on your CX Truck Cap that only has tracks, you would need to add crossbars. The A.R.E toppers use either Yakima or Thule tracks. Both of those would be compatible with the Replacement Yakima Control Tower # Y8890027 (you would need to get 4), the Landing Pad 1 for Yakima SkyLine and Control Towers # Y00221 (you would need to get 2) and the Round 66" CrossBars for Yakima Roof Rack System # Y00410.
view full answer... - Yakima Cargo Rack on my RetraxOne XR Tonneau CoverI have a solution for you that will get you exactly what you want. It will consist of 1 set of 4 SkyLine Towers for Yakima Crossbars part # Y53TR , two sets of the Landing Pad 1 for Yakima Control Towers - Qty 2 part # Y00221 , one of the RoundBar SL Adapter for Yakima SkyLine Towers - Qty 4 part # Y03536 , one of the Yakima Same Key System (SKS) Lock Cores 4 pack part # Y07204 and either the Round 66" CrossBars for Yakima Roof Rack System (QTY 2) part # Y00410 or the Round 78" CrossBars...
view full answer... - Roof Rack Recommendation for a 1995 Pontiac Grand Prix 2 DR CoupeI recommend going with a Yakima Roof Track System for your 1995 Pontiac Grand Prix 2 Dr Coupe. This track mounts directly to the roof of your Grand Prix with PlusNut hardware. Installation does require drilling through the roof of your vehicle so if you are uncomfortable doing this yourself, I strongly encourage you to take your vehicle to a local body shop to have the track system installed. Each component for the Yakima Roof Track System is sold separately so in order to have the complete...
view full answer... - Roof Rack and Kayak Carrier Recommendation for Leer Camper Shell with Tracks on a Ford F-150I have what you need! Even though we have amazing options for installing a complete roof rack system on your Ford F-150 with a Leer camper shell, installing the WingBar Evo Crossbars onto a track system is a complicated process. This is because with the WingBar Evo crossbars, they come with bottom channels that do not extend the entire length of the bottom of the crossbar. With that being the case, there is no way to fully determine what WingBar Evo crossbars you need unless we have the...
view full answer... - Can The Side Rails On The Pace Edwards Bedlocker Be Upgraded To The Explorer Rails?The Replacement Explorer Rails for Pace Edwards Bedlocker Hard Tonneau Cover # PE39CV are the replacement rails for the Pace Edwards Bedlocker Retractable Hard Tonneau Cover # 311-BLD2336, which only fits select years of the Dodge Ram 1,500, 2,500, and 3,500, and not your 2020 Ford F-350 unfortunately. The only way that you could get the explorer rails for your 2020 Ford F-350, is to purchase and entire new Bedlocker system with the rails already installed. If you're interested, we do...
view full answer... - Will the Rhino-Rack # Y01-130B Fit My 2022 Hyundai Santa Cruz?Yes, you will be able to put 2 bikes on the Rhino-Rack Heavy-Duty Bar Roof Rack for Camper Shells - Track Mount # Y01-130B if the combined weight of the racks and bikes is exactly 220 pounds (or under). As far as the fitment of the # Y01-130B on your 2022 Hyundai Santa Cruz, that is a bit more complicated. The tracks will fit with the included hardware with drilling. With the 63" tracks, you can cut the tracks to the size of the bed rails. The complicated part is the crossbar fitment....
view full answer... - Roof Rack for 2017 Chevy Colorado Crew Cab with Naked RoofWhile we have some good options for a roof rack on your 2017 Chevy Colorado Crew Cab with a naked roof, the Rhino-Rack tracks will only fit Rhino-Rack feet so they aren't compatible with your current Yakima towers. The best option is a roof rack from Rhino-Rack that does not require drilling to install tracks in your roof and is also more budget-friendly than using your Yakima bars with a track system. It would require the following: - Rhino-Rack Vortex Aero Crossbars # RRVA126B-2 -...
view full answer... - How To Mount Yakima Towers In Retrax Tonneau Cover TracksIf you have the Yakima Skyline or Control Towers then you can use the Landing Pad 1 for Yakima SkyLine and Control Towers part # Y00221 to mount them into tracks/channels like those found on select Retrax Tonneau Covers.
view full answer... - Yakima Parts to Fit American Roll Cover Tonneau Cover on a 2020 Chevy Silverado 1500I'd be happy to help! The Yakima SkyLine Towers # Y53TR are compatible directly with the JetStream crossbars so no adapter kit is needed, but if you're installing this over a truck bed you need the Yakima HD bars which do require an adapter. Unfortunately, crossbars and leg systems aren't compatible from one manufacturer to the other so you'll need to stick with Yakima crossbars for your application. If you already have the fit kit (which I believe is 2 of the Landing Pad # Y00221) for...
view full answer... - Correct Length of Yakima HD Bars for Retrax XR Tonneau Cover on 2019 Ram 1500Thank you for the info! The 68" HD Yakima Crossbars # Y01158 will be what you want to use with the Retrax XR tonneau cover on your 2019 Ram 1500. You mentioned having the SkyLine Towers and SL Adapters but you also need the Landing Pad 1 to fit the towers to your XR rails. Altogether you need the following: 68" HD Crossbars - # Y01158 SkyLine Towers - # Y53TR HD Bar SL Adapter - # Y03541 Landing Pad 1 - # Y00221 (you need 2 of these) Lock Core Set - # Y07204 (optional) Hope this helps!
view full answer... - Converting Yakima BedRock HD Crossbars To Work With RetraxOne XR Tonneau On a 2017 Nissan TitanYou will be able to adapt the bars from the Yakima BedRock HD Truck Bed Rack # Y01160-59 to fit the RetraxONE XR Hard Tonneau Cover # RTT-60752 for the 6-1/2' bed on your 2017 Nissan Titan. Since the towers with the BedRock require you to mount inside the bed rails they will prevent the cover from fitting. The RetraxONE XR comes with t-slot accessory rails that you will be able to fit four of the SkyLine Tower # 8880614 using 2 sets of Landing Pads # Y00221. You will then be able to move...
view full answer... - Recommended Yakima Roof Rack For 2002 Ford Excursion With Factory Roof Rack For Yakima Cargo BoxI called my contact at Yakima about the Yakima SkyBox 21 Rooftop Cargo Box, part # Y07337. They told me they have not verified a fit for the cargo box with the factory crossbars on your Excursion. They told me the cargo box may fit but there is no guarantee. I have attached a drawing that shows the size and shape of the crossbars the # Y07337 cargo box will fit so you can take a quick measurement. If you find the cargo box will not fit they suggest removing your factory crossbars and...
view full answer...
- Parts Needed to Install Yakima Round Bar Roof on 2001 Toyota 4Runner with Roof TracksThanks for the pictures of your rack. You have a Yakima Round Bar setup that has been updated so while you'd be able to reuse your roundbars on your 2001 Toyota 4Runner you'd need a new set of feet and fit kit. For that you'd need the SkyLine Towers for Yakima Crossbars # Y00148 Landing Pad 1 # Y00221 RoundBar adapter part # Y03536 You already have the roundbars but for that you'd normally use the part # Y00409
view full answer...
- Can Yakima Tracks for Roof Racks be Slightly Bent During Install on Tear CamperI reached out to Yakima in regards to bending the Yakima 42" Tracks for Roof Racks # Y01126 and they told me that yes it is okay to bend the tracks during the installation. For the rest of the installation you can use a quantity of two of the Landing Pad 1 # Y00221, along with four of the Yakima Control Tower # Y8890027 and round bars like the 58 inch # Y00409, 66 inch # Y00410, or 78 inch # Y00411, depending on the size of your camper's roof.
view full answer... - Yakima HD Crossbar Rack For Retrax Pro XR Tonneau CoverYou'll need an adapter but yes, the Yakima HD crossbars will work with the Retrax Pro XR tonneau cover. What you can use is the following: - Yakima HD Crossbars - 60" Long # Y01157, 68" Long # Y01158, or 78" Long # Y01159 (you'll need to measure to get the correct length - Landing Pad 1 # Y00221 (you'll need to order Qty 2 of this part number) - SkyLine Towers for Yakima Crossbars # Y53TR - HD Bar SL Adapter for Yakima BaseLine, SkyLine, TimberLine, and RidgeLine Towers # Y03541
view full answer... - How To Identify A Set of Roof Tracks On A Camper ShellIf you were to measure the width of the track that would then give you the best chance of identifying it. However, this really is not needed because the slots are pretty much universal so you can mix and max brands. The most cost effective system we would have is going to be a Yakima Round Bar System. The round crossbars are cut to fit. In order to obtain this you will need to order the following: Round 78" CrossBars for Yakima Roof Rack System part # Y00411 (Qty 1) Replacement Yakima...
view full answer... - Hard Tonneau Cover Bike Rack for 2019 Ram 2500 Short BedWe do not have a bike carrier that mounts directly to a hard tonneau cover, however there is another solution. If you have room on you bed rail outside of the tonneau cover you can mount the equivilent of a roof rack on your bed rails using the following parts. Skyline Towers # Y53TR Yaamkia Landing Pads and control towers # Y00221 Yakima 58" Crossbars # Y00409 Yakima Round Bar Adapter # 8003536 With a complete rack system built you need only to choose the "roof" bike carriers that...
view full answer... - Parts Needed to Install Yakima Roof Rack on Leer Camper Shell with Roof TracksWe have the Yakima roof rack components needed to install in the tracks on top of your Leer 100XR camper shell. To complete your roof rack setup you will need: quantity 2 of the Landing Pad 1 # Y00221 quantity 4 of the Control Towers # Y8890027 and depending on the length of your cap quantity 2 Crossbars like: 48 inch # Y00408 58 inch # Y00409 66 inch # Y00410 78 inch # Y00411 To lock your roof rack to your tracks, I recommend the set of 4 lock cores with keys # Y07204.
view full answer... - Parts Needed to Install Yakima Round Bar Roof Rack on Camper Shell with TracksTo install a set of Yakima round crossbars on your camper shell with roof rack tracks you'd want need 4 of the Yakima Control Towers # Y8890027, 2 sets of the Yakima Landing Pad # Y00221, and one set of Yakima round crossbars, which come in varying lengths. For 58 inch bars use # Y00409 For 66 inch bars use # Y00410 For 78 inch bars use # Y00411
view full answer... - Available Roof Racks for Various Roof Styles on 1987 Jeep CherokeeWe can help you with a roof rack for your 1987 Jeep Cherokee. The rack fits depend on how the Cherokee's roof is set up. On the linked page just click on the picture that shows your roof style; you will then see only the racks that fit that type of roof. We have options from several brands but none of the roof configurations shows a fit for a SportRack brand roof rack. However, I can help you find the most cost-effective option for each type of roof. If you have a factory roof rack with...
view full answer... - Roof Rack Recommendation for 1983 HiLo 25L Voyager CamperI do have a solution for you but the SportRack Pop-Up Camper Roof Rack # SR1020 won't work because of the 91.5 inch width of your camper. The SportRack Pop-Up Camper Roof Rack # SR1020 works with a maximum width of 85.5 inches which is the only version available. Based on my research, the only other solution is to install a pair of Yakima 60" Tracks # Y01135 (longest available) a few inches inside the edge of your camper's roof along with the Round 86" CrossBars for Yakima Roof-Rack System...
view full answer... - Recommended Track System for Cargo Platform on 2003 Toyota Tacoma with TopperThe Yakima 60" Tracks for Roof Racks # Y01135 will work well on a sheet metal roof. You will want to be as close to the frame weight supports as possible to maximize the weight capacity. It sounds like you want to do a customized fit but I don't recommend running the track between the cab and topper. I'd use two separate tracks that are lined up so there is the ability to remove the topper if ever desired and you won't have the chance of an unsupported tower sitting in the gap between...
view full answer... - Roof Rack Fit Recommendation for ARE Truck TopperThere were versions of the A.R.E. camper shells that had tracks on them already. The factory rails were made by Yakima. For a complete roof rack system on your A.R.E. topper you will need the following parts if you have the rails: 4 of the Yakima Control Towers # Y8890027 2 sets (2ea) Yakima Landing Pad 1 # Y00221 1 set (2ea) Yakima Crossbars: 58 inch bars are # Y00409 66 inch bars are # Y00410 78 inch bars are # Y00411
view full answer... - What Crossbar System Accommodates a Rooftop Tent on My 2017 Honda Accord? For your 2017 Honda Accord with a bare roof without fixed mounting points, the best option is a system that involves drilling. This is because all of the non-drilling options for your vehicle include door jamb clamps that are not recommended for supporting the extra weight associated with a roof top tent setup. Manufacturers strongly discourage this because door jamb clamps setups can buckle and become detached with the weight. With that being said, I recommend the following track system:...
view full answer... - What Parts Are Needed to Use a Roof Top Tent on a CX Truck CapTo use a roof top tent like the Yakima SkyRise HD Tent # Y07437 on your CX Truck Cap that only has tracks, you would need to add crossbars. The A.R.E toppers use either Yakima or Thule tracks. Both of those would be compatible with the Replacement Yakima Control Tower # Y8890027 (you would need to get 4), the Landing Pad 1 for Yakima SkyLine and Control Towers # Y00221 (you would need to get 2) and the Round 66" CrossBars for Yakima Roof Rack System # Y00410.
view full answer... - Yakima Cargo Rack on my RetraxOne XR Tonneau CoverI have a solution for you that will get you exactly what you want. It will consist of 1 set of 4 SkyLine Towers for Yakima Crossbars part # Y53TR , two sets of the Landing Pad 1 for Yakima Control Towers - Qty 2 part # Y00221 , one of the RoundBar SL Adapter for Yakima SkyLine Towers - Qty 4 part # Y03536 , one of the Yakima Same Key System (SKS) Lock Cores 4 pack part # Y07204 and either the Round 66" CrossBars for Yakima Roof Rack System (QTY 2) part # Y00410 or the Round 78" CrossBars...
view full answer... - Roof Rack Recommendation for a 1995 Pontiac Grand Prix 2 DR CoupeI recommend going with a Yakima Roof Track System for your 1995 Pontiac Grand Prix 2 Dr Coupe. This track mounts directly to the roof of your Grand Prix with PlusNut hardware. Installation does require drilling through the roof of your vehicle so if you are uncomfortable doing this yourself, I strongly encourage you to take your vehicle to a local body shop to have the track system installed. Each component for the Yakima Roof Track System is sold separately so in order to have the complete...
view full answer... - Roof Rack and Kayak Carrier Recommendation for Leer Camper Shell with Tracks on a Ford F-150I have what you need! Even though we have amazing options for installing a complete roof rack system on your Ford F-150 with a Leer camper shell, installing the WingBar Evo Crossbars onto a track system is a complicated process. This is because with the WingBar Evo crossbars, they come with bottom channels that do not extend the entire length of the bottom of the crossbar. With that being the case, there is no way to fully determine what WingBar Evo crossbars you need unless we have the...
view full answer... - Can The Side Rails On The Pace Edwards Bedlocker Be Upgraded To The Explorer Rails?The Replacement Explorer Rails for Pace Edwards Bedlocker Hard Tonneau Cover # PE39CV are the replacement rails for the Pace Edwards Bedlocker Retractable Hard Tonneau Cover # 311-BLD2336, which only fits select years of the Dodge Ram 1,500, 2,500, and 3,500, and not your 2020 Ford F-350 unfortunately. The only way that you could get the explorer rails for your 2020 Ford F-350, is to purchase and entire new Bedlocker system with the rails already installed. If you're interested, we do...
view full answer... - Will the Rhino-Rack # Y01-130B Fit My 2022 Hyundai Santa Cruz?Yes, you will be able to put 2 bikes on the Rhino-Rack Heavy-Duty Bar Roof Rack for Camper Shells - Track Mount # Y01-130B if the combined weight of the racks and bikes is exactly 220 pounds (or under). As far as the fitment of the # Y01-130B on your 2022 Hyundai Santa Cruz, that is a bit more complicated. The tracks will fit with the included hardware with drilling. With the 63" tracks, you can cut the tracks to the size of the bed rails. The complicated part is the crossbar fitment....
view full answer... - Roof Rack for 2017 Chevy Colorado Crew Cab with Naked RoofWhile we have some good options for a roof rack on your 2017 Chevy Colorado Crew Cab with a naked roof, the Rhino-Rack tracks will only fit Rhino-Rack feet so they aren't compatible with your current Yakima towers. The best option is a roof rack from Rhino-Rack that does not require drilling to install tracks in your roof and is also more budget-friendly than using your Yakima bars with a track system. It would require the following: - Rhino-Rack Vortex Aero Crossbars # RRVA126B-2 -...
view full answer... - How To Mount Yakima Towers In Retrax Tonneau Cover TracksIf you have the Yakima Skyline or Control Towers then you can use the Landing Pad 1 for Yakima SkyLine and Control Towers part # Y00221 to mount them into tracks/channels like those found on select Retrax Tonneau Covers.
view full answer... - Yakima Parts to Fit American Roll Cover Tonneau Cover on a 2020 Chevy Silverado 1500I'd be happy to help! The Yakima SkyLine Towers # Y53TR are compatible directly with the JetStream crossbars so no adapter kit is needed, but if you're installing this over a truck bed you need the Yakima HD bars which do require an adapter. Unfortunately, crossbars and leg systems aren't compatible from one manufacturer to the other so you'll need to stick with Yakima crossbars for your application. If you already have the fit kit (which I believe is 2 of the Landing Pad # Y00221) for...
view full answer... - Correct Length of Yakima HD Bars for Retrax XR Tonneau Cover on 2019 Ram 1500Thank you for the info! The 68" HD Yakima Crossbars # Y01158 will be what you want to use with the Retrax XR tonneau cover on your 2019 Ram 1500. You mentioned having the SkyLine Towers and SL Adapters but you also need the Landing Pad 1 to fit the towers to your XR rails. Altogether you need the following: 68" HD Crossbars - # Y01158 SkyLine Towers - # Y53TR HD Bar SL Adapter - # Y03541 Landing Pad 1 - # Y00221 (you need 2 of these) Lock Core Set - # Y07204 (optional) Hope this helps!
view full answer... - Converting Yakima BedRock HD Crossbars To Work With RetraxOne XR Tonneau On a 2017 Nissan TitanYou will be able to adapt the bars from the Yakima BedRock HD Truck Bed Rack # Y01160-59 to fit the RetraxONE XR Hard Tonneau Cover # RTT-60752 for the 6-1/2' bed on your 2017 Nissan Titan. Since the towers with the BedRock require you to mount inside the bed rails they will prevent the cover from fitting. The RetraxONE XR comes with t-slot accessory rails that you will be able to fit four of the SkyLine Tower # 8880614 using 2 sets of Landing Pads # Y00221. You will then be able to move...
view full answer... - Recommended Yakima Roof Rack For 2002 Ford Excursion With Factory Roof Rack For Yakima Cargo BoxI called my contact at Yakima about the Yakima SkyBox 21 Rooftop Cargo Box, part # Y07337. They told me they have not verified a fit for the cargo box with the factory crossbars on your Excursion. They told me the cargo box may fit but there is no guarantee. I have attached a drawing that shows the size and shape of the crossbars the # Y07337 cargo box will fit so you can take a quick measurement. If you find the cargo box will not fit they suggest removing your factory crossbars and...
view full answer... - Parts Needed to Install Yakima Round Bar Roof on 2001 Toyota 4Runner with Roof TracksThanks for the pictures of your rack. You have a Yakima Round Bar setup that has been updated so while you'd be able to reuse your roundbars on your 2001 Toyota 4Runner you'd need a new set of feet and fit kit. For that you'd need the SkyLine Towers for Yakima Crossbars # Y00148 Landing Pad 1 # Y00221 RoundBar adapter part # Y03536 You already have the roundbars but for that you'd normally use the part # Y00409
view full answer... - Can Yakima Tracks for Roof Racks be Slightly Bent During Install on Tear CamperI reached out to Yakima in regards to bending the Yakima 42" Tracks for Roof Racks # Y01126 and they told me that yes it is okay to bend the tracks during the installation. For the rest of the installation you can use a quantity of two of the Landing Pad 1 # Y00221, along with four of the Yakima Control Tower # Y8890027 and round bars like the 58 inch # Y00409, 66 inch # Y00410, or 78 inch # Y00411, depending on the size of your camper's roof.
view full answer... - Yakima HD Crossbar Rack For Retrax Pro XR Tonneau CoverYou'll need an adapter but yes, the Yakima HD crossbars will work with the Retrax Pro XR tonneau cover. What you can use is the following: - Yakima HD Crossbars - 60" Long # Y01157, 68" Long # Y01158, or 78" Long # Y01159 (you'll need to measure to get the correct length - Landing Pad 1 # Y00221 (you'll need to order Qty 2 of this part number) - SkyLine Towers for Yakima Crossbars # Y53TR - HD Bar SL Adapter for Yakima BaseLine, SkyLine, TimberLine, and RidgeLine Towers # Y03541
view full answer... - How To Identify A Set of Roof Tracks On A Camper ShellIf you were to measure the width of the track that would then give you the best chance of identifying it. However, this really is not needed because the slots are pretty much universal so you can mix and max brands. The most cost effective system we would have is going to be a Yakima Round Bar System. The round crossbars are cut to fit. In order to obtain this you will need to order the following: Round 78" CrossBars for Yakima Roof Rack System part # Y00411 (Qty 1) Replacement Yakima...
view full answer... - Hard Tonneau Cover Bike Rack for 2019 Ram 2500 Short BedWe do not have a bike carrier that mounts directly to a hard tonneau cover, however there is another solution. If you have room on you bed rail outside of the tonneau cover you can mount the equivilent of a roof rack on your bed rails using the following parts. Skyline Towers # Y53TR Yaamkia Landing Pads and control towers # Y00221 Yakima 58" Crossbars # Y00409 Yakima Round Bar Adapter # 8003536 With a complete rack system built you need only to choose the "roof" bike carriers that...
view full answer... - Parts Needed to Install Yakima Roof Rack on Leer Camper Shell with Roof TracksWe have the Yakima roof rack components needed to install in the tracks on top of your Leer 100XR camper shell. To complete your roof rack setup you will need: quantity 2 of the Landing Pad 1 # Y00221 quantity 4 of the Control Towers # Y8890027 and depending on the length of your cap quantity 2 Crossbars like: 48 inch # Y00408 58 inch # Y00409 66 inch # Y00410 78 inch # Y00411 To lock your roof rack to your tracks, I recommend the set of 4 lock cores with keys # Y07204.
view full answer... - Parts Needed to Install Yakima Round Bar Roof Rack on Camper Shell with TracksTo install a set of Yakima round crossbars on your camper shell with roof rack tracks you'd want need 4 of the Yakima Control Towers # Y8890027, 2 sets of the Yakima Landing Pad # Y00221, and one set of Yakima round crossbars, which come in varying lengths. For 58 inch bars use # Y00409 For 66 inch bars use # Y00410 For 78 inch bars use # Y00411
view full answer... - Available Roof Racks for Various Roof Styles on 1987 Jeep CherokeeWe can help you with a roof rack for your 1987 Jeep Cherokee. The rack fits depend on how the Cherokee's roof is set up. On the linked page just click on the picture that shows your roof style; you will then see only the racks that fit that type of roof. We have options from several brands but none of the roof configurations shows a fit for a SportRack brand roof rack. However, I can help you find the most cost-effective option for each type of roof. If you have a factory roof rack with...
view full answer...
Do you have a question about this Roof Rack?
Info for this part was:
Edited by:
Daron K
Written by:
Alex H
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.