Customers compare BUL12CFB to these similar products
Products Featured in this Video
Today, we'll be reviewing part number BUL12CFB. This is the Optronics LED backup light. The clear oblong light will function as a backup light. It is certified for backup light function, when installed as a pair, in a two lamp system. It's going to feature long lasting LEDs. They are also going to work great for replacements for incandescent lights. It's going to feature a multi-diode design,… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The Mighty Cord Replacement Hardwire RV Plug part #A10-P30VP is about 4" long x 2-1/2" wide x 2-1/4" thick. This should fit inside your power cord hatch but you will need to measure to be certain.
view full answer...Sounds like you are wanting to know if the Fan-Tastic Vent 3350 Series Upgrade Kit #FV803358 is the correct kit for your roof vent. Basically this is designed to fit the Fan-Tastic Roof Vents to turn it into a 3350 series of Fan-Tastic Vents like…
view full answer...The Mighty Cord Replacement Hardwire RV Plug, part #A10-P30VP, can be used outdoors but this plug can not be exposed directly to the elements since it is not 100% waterproof. As long as there is a door or other form of protection on the power outlet…
view full answer...The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…
view full answer...The head in the picture is the Reese #RP54980 however the trunnion spring bars to fit are no longer available. Unfortunately, your best bet may be to replace the entire system. If an 800 pound rated system is enough for you I recommend the Fastway e2…
view full answer...Reese doesn't offer a spring bar handle as a replacement part for the #RE44FR weight distribution kit, but luckily the Equal-i-zer #EQ95-01-6050 would work for you.
view full answer...Your trailer battery is the reason the 12 volt accessory circuit on the 7-way part #HM48503 is lighting up all the time. It's voltage is backfeeding to the connector and lighting the LED. This LED draws such a low amount it would take a very long…
view full answer...To connect back up lights you need to have a 7-way trailer connector on both your trailer and tow vehicle. On a 7-way the reverse lights are powered by the center pin. To connect reverse lights to the trailer's 7-way you can use 16 gauge wire…
view full answer...While your frustration is understandable and we have a solution for you, I wouldn't be able to tell you with absolute certainty that using the Stromberg Carlson Electric Trailer Jack #JET-3755 will stop your tailgate from hitting the jack. The…
view full answer...The #PSEA20000103 is one of the shortest A-frame jacks we offer from the mounting bracket to the top of the jack at 11 inches. The best solution I can recommend would be to go with a side mounted trailer jack like part #PS1400300303 that would…
view full answer...It is likely that the red wire on your old lights is the turn signal/brake light wire, and the black wire is the running light wire. That would make the white wire the ground. You can verify this by testing the wires using a circuit tester such as…
view full answer...11 inches from the bolt hole centers to the wall of the RV is the standard dimension for installing a 2 bolt toilet like the Dometic part #DOM87FR. You might check again and see if you didn't measure from the bolt centers and instead did from the…
view full answer...