Customers compare DM34GV to these similar products
Products Featured in this Video
Hi there. I'm Michael with etrailer.com. Today, we're gonna take a quick look at these Demco side plates. These are going to replace the side plates on your 31,000-pound capacity Demco Hijacker UMS fifth-wheel trailer hitch. This is going to be a direct replacement for the part number that you see on the screen there. That is designed for your 2011 and newer Ford trucks with the factory-installed… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
For your 2021 Jeep Gladiator Rubicon you are correct that there are two trailer hitch receivers available, the Curt #CU74FR and the etrailer #e67AR. Both of these hitches are very similar in the sense that they install in virtually the exact same…
view full answer...I have added a cutout of the linked installation instructions for the Draw-Tite Trailer Hitch Receiver #DR64FR that fits your 2020 Jeep Gladiator which show that you do not have to drill to install the hitch on your Jeep. When putting this hitch on…
view full answer...We do offer a 'full' hitch for your 2021 Jeep Gladiator Mojave. You'll want to use the Draw-Tite #DR64FR which is a confirmed fit for your vehicle. The hitch is a bolt-on application, and no drilling would be required to complete the…
view full answer...If your OEM hitch is simply bolted into place onto the crossmember, you could indeed remove it and install the Draw-Tite 76310 which we sell as #DR64FR Class III hitch in its place. If the existing hitch is welded into place, it could be an integral…
view full answer...I checked with Curt and according to them, the Curt Trailer Hitch Receiver #CU74FR is a fit for all models of the 2020 Jeep Gladiator, including the Sport. You are correct that it will install partially through the ball mount hole in the bumper, as…
view full answer...You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…
view full answer...I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…
view full answer...Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…
view full answer...I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine, as…
view full answer...