Features: Fits 8,000 lb axles Capacity: 4,000 lb each Works with both electric and hydraulic brakes Drum size: 12-1/4" x 3-3/8" Stud diameter: 9/16" Parts included: Cartridge bearing 50MM x 84MM x 54MM (31-71-3) Snap ring, inner bearing retainer, 3.35" O.D. (69-93) Snap ring, outer bearing retainer,.821" O.D. (69-96) Grease Cap, 3.355" O.D., Drive-In (75DC) Drive-In Studs, 9/16" Diameter (7-132) 9/16" Cone Wheel Nut (6-53) Hub and drum are made in the USA
Winterizing your RV? This Flair-It bypass valve lets you reroute water around your water heater in minutes. Just hand-tighten nuts for a leak resistant seal and enjoy tool-free prep for every season.Turn the handle to send water where you need it and get on with your work. Specs Fitting type: 3-Way Bypass Valve Connection size: 1/2" barb x 1/2" barb x 1/2" barb Compatible pipe: 1/2" PEX, bolybutylene (PB), polyvinyl tubing Material: Polyoxymethylene (POM) Maximum temperature: 180 F Maximum pressure: 100 PSI
Need to bypass your RVs water heater for winterizing? This PEXLock valve makes it simple to divert water between lines. Install with pliers for quick seasonal prep with no special tools and less stress.Specs Fitting type: PEXLock Bypass Valve (3-way) Connection size: 1/2" barb x 1/2" barb x 1/2" barb Compatible pipe: 1/2" PEX, PERT tubing, IAPMO approved polyvinyl tubing Material: Reinforced polyoxymethylene (POM) fitting, engineered plastic PEXLock clamps Maximum temperature: 180 F Maximum pressure: 100 PSI Included: 1 valve and 3 PEXLock clamps
Adding a new fixture or rerouting water in your RV? The Flair-It T-connector makes it easy to create new lines for a kitchen upgrade or installing an outdoor shower. No special tools required - just hand-tighten and get back to your adventure.You can also remove and reuse the fitting if plans change. Specs Fitting type: t-connector Connection size: 1/2" barb x 1/2" barb x 1/2" barb Compatible pipe: PEX, polybutylene (PB), polyvinyl tubing Material: polyoxymethylene (POM) Maximum temperature: 180 F Maximum pressure: 100 PSI
Diverter valve controls water lines in your RV when it's time to winterize. Quickly changes the flow to prevent antifreeze from getting into your hot water heater.Features: Diverter valve lets you change the flow of water in your RV's fresh-water system Often installed near your hot water heater as a bypass to keep antifreeze out when winterizing Also used to create a new input to siphon antifreeze into your fresh-water lines Knob rotates to change flow from one of one of two inputs to a single output Also lets you change flow from one input to one of two outputs Fitting size: 1/2" MPT x 1/2" MPT x 1/2" FPT 1-Year warranty
This fresh-water plumbing T-connector features (3) 1/2" barbed connections for diverting water in your RV. Polypropylene material is suitable for repairing or installing new lines your fresh-water system.Features: Coupler connects hoses and diverts water in your RV fresh-water plumbing system Used for repairing leaky connections or installing new lines 1/2" Barbed connection on all 3 ends fits 1/2" inner diameter hoses Needs hose clamp for secure fitting Black polypropylene construction
This fresh-water plumbing T-connector features a 1/2" MPT connection and (2) 1/2" barbed connections for diverting water in your RV. Polypropylene material is suitable for repairing or installing new lines your fresh-water system.Features: Coupler connects hoses and diverts water in your RV fresh-water plumbing system Used for repairing leaky connections or installing new lines 3/8" Barbed connection on 2 ends fits 3/8" inner diameter hoses Needs hose clamp for secure fitting 1/2" MPT connection on 1 end fits hoses or fresh-water tanks with 1/2" FPT fittings Thread tape recommended for secure installation Black polypropylene construction
Tired of leaks or corrosion in your RV water lines? PEXLock makes adding a new branch quick and worry free. No metal to rust, no special tools; just a few minutes with pliers and you're back to enjoying your travels.Just simple, reliable plumbing upgrades you can do yourself. Specs Fitting type: PEXLock T Connector Connection size: 1/2" barb x 1/2" barb x 1/2" barb Compatible pipe: PEX, PERT tubing, IAPMO-approved polyvinyl tubing Material: Polyoxymethylene (POM) fitting, engineered plastic PEXLock clamps Maximum temperature: 180 F Maximum pressure: 100 PSI Included: 1 fitting and 3 PEXLock clamps Certifications: NSF certified for potable water systems Durability: corrosion, chemical, and electrolysis resistant high impact plastic
Tired of leaks or corrosion in your RV water lines? PEXLock makes adding a new branch quick and worry free. No metal to rust, no special tools; just a few minutes with pliers and you're back to enjoying your travels.Highlights Connect to Threaded Fixtures: Easily branch a 1/2" PEX, PERT, or polyvinyl line to a threaded appliance, valve, or filter using the 1/2" MPT outlet. No Metal, No Corrosion: All plastic PEXLock system stands up to hard or acidic water, corrosion, and electrolysis.
Hub-and-rotor assembly works with 7,000-lb Dexter disc brakes. E-coat finish protects against corrosion. Vented design prevents heat-related damage. Inner bearing (25580), outer bearing (14125A), races, grease seal, and grease cap included.Features: Hub-and-rotor assembly works with 7,000-lb Dexter disc brakes Machined process minimizes runout and warping Contaminants can't get in between rotor and hub Vented design regulates temperature to prevent overheating Wheel studs, bearings, races, grease seal, and grease cap included Cast iron construction provides strength and durability E-coat finish protects against corrosion and wear Made in the USA Specs: Fits: Axle capacity: 7,000 lbs Wheel size: 16", 16-1/2", and 17" Bolt pattern: 8 on 6-1/2" Wheel bolt diameter: 1/2" Rotor diameter: 12-1/4" 5-Year limited warranty Bearing, Race, and Seal Information Bearings (included) Inner bearing: 25580 (1.75" inner diameter) Outer bearing: 14125A (1.25" inner diameter) Races (included) Inner race: 25520 Outer race: 14276 Grease seal (included): GS-2250DL Inner diameter: 2.25" Outer diameter: 3.376"
Need to run a water line to your RV's ice maker or small appliance? The Flair-It ice maker tee lets you branch off a 1/2" water line using the tool-free barbed ends and connect your appliance to the 1/8" NPT port with a wrench.You can reuse the fitting if you upgrade or move your appliance later. Specs Fitting type: ice maker tee Connection size: 1/2" barb x 1/2" barb x 1/8" Female NPT Compatible pipe: PEX, Polybutylene (PB), Polyvinyl tubing Accessory port: 1/8" Female NPT (for ice maker or filter supply tube) Material: Polyoxymethylene (POM) Maximum temperature: 180 F Maximum pressure: 100 PSI
Hub-and-rotor assembly works with 7,000-lb Dexter disc brakes. E-coat finish protects against corrosion. Vented design prevents heat-related damage. Inner bearing (25580), outer bearing (14125A), races, oil seal, and oil cap included.Features: Hub-and-rotor assembly works with 7,000-lb Dexter disc brakes Machined process minimizes runout and warping Contaminants can't get in between rotor and hub Vented design regulates temperature to prevent overheating Wheel studs, bearings, races, oil seal, and oil cap included Cast iron construction provides strength and durability E-coat finish protects against corrosion and wear Made in the USA Specs: Fits: Axle capacity: 7,000 lbs Wheel size: 16", 16-1/2", and 17" Bolt pattern: 8 on 6-1/2" Wheel bolt diameter: 1/2" Rotor diameter: 12-1/4" 5-Year limited warranty Bearing, Race, and Seal Information Bearings (included) Inner bearing: 25580 (1.75" inner diameter) Outer bearing: 14125A (1.25" inner diameter) Races (included) Inner race: 25520 Outer race: 14276 Oil seal (included): 10-63 Inner diameter: 2.25" Outer diameter: 3.376"
Need to connect your tank to the tubing for your water level system? These fittings adapt 1/2" BSP threaded ports to 1/2" push-fit tubing, making it easy to link your tank to the sender for accurate water level readings.Highlights Water Gauge Connection: Adapts 1/2" BSP threaded ports to 1/2" push-fit PE tubing for sender setup. Quick Tubing Attachment: Push-fit connection secures 12.7 mm OD tubing without extra tools or complex setup.
Need to connect mismatched fittings in your setup? These adapters link 1/2" BSP female threads to 1/2" NPT male connections, making it easy to bridge different thread types and keep your system properly connected. ... Highlights BSP-to-NPT Connection: Links 1/2" BSP female threads to 1/2" NPT male fittings in tank setups. Thread Type Adaptation: Bridges mismatched BSP and NPT fittings to keep plumbing connections usable.
Oil leaked, water got in, and the bearings are shot on your 7,000-lb #42 spindle. Not every hub will fit on that setup. This galvanized idler hub is built to replace threaded Dexter Vortex oil bath hubs, restoring function without changing the axle.Long Wheel Studs for Brake and Wheel Fitment Thick wheel mounting pads and over-the-hub brake rotors require more thread engagement. The 1/2 inch diameter x 2-1/2 inch long studs with 1/2 inch-20 bolt size provide the added length needed for those setups. You avoid running short on threads during final torque.
Need to connect your PEX line to a threaded fitting in a tight spot? This swivel elbow makes it simple. Snap on the clamp, tighten the swivel nut, and get a leak resistant, road-ready connection in minutes.Highlights Connect PEX to Threaded Lines: Easily join your 1/2" PEX pipe to any 1/2" MPT fitting in your RVs fresh-water system. Swivel Nut Makes Install Easy: Swiveling female NPT end lets you tighten the fitting without twisting or kinking your supply line.
Need to join a 1/2" water line to a threaded fitting in a cramped spot? The Flair-It swivel elbow makes it easy. Thread on the swivel nut, hand-tighten the barb side, and get a leak resistant seal in minutes with no special tools needed.Highlights Connect PEX to Threaded Lines: Join your 1/2" PEX, PB, or polyvinyl water line to a 1/2" MPT fitting anywhere in your RV. Swivel Nut Simplifies Tight Installs: The swiveling female end lets you thread onto a fitting without twisting or kinking your pipe.
Need to drain your RVs water lines for storage or winterizing? The Flair-It angle drain valve makes it easy to add a low-point drain. Just hand-tighten for a secure seal and empty your lines whenever you need.Specs Fitting type: Angle Drain Valve Connection size: 1/2" barb x 1/2" barb Compatible pipe: 1/2" PEX, polybutylene (PB), polyvinyl tubing Material: Polyoxymethylene (POM) Maximum temperature: 180 F Maximum pressure: 100 PSI
If your city water connection is causing your fresh-water tank to overflow, get a new check valve. Install this check valve to stop water from backing up and keep it flowing in the right direction.Features: Check valve lets water flow in only one direction Used to prevent city water connection from filling and overflowing your fresh-water tank Also prevents water from backflowing out of your hot water heater Brass construction is lead-free and safe to use Fitting size: 1/2" MPT x 1/2" FPT 1-Year warranty
Replace the leaking check valve in your RV's fresh-water system to prevent backflow and keep antifreeze from leaking into your water heater. Brass construction won't rust. Valve has both 1/2" MPT and 1/2" FPT ends.Features: Brass check valve replaces a leaking valve in your RV's fresh-water system Check valve prevents backflow and keeps contaminants out of your water Lead-free brass won't contaminate water or rust over time Specs: Fitting size: 1/2" MPT x 1/2" FPT Overall length: 2"
Route fresh-water pipes in your RV with this 90-degree elbow fitting. Connects two 1/2" female NPT fittings on hoses, collars, and pipe adapters.Features: Elbow connects pipes and hoses in your RV fresh-water plumbing system Used for repairing leaky connections or installing new lines 1/2" Male NPT threads connect to female fittings Poly alloy construction is durable and resistant to stress cracking
Use this adapter fitting to transition your 1/2" PEX pipe to a fresh-water line with a 1/2" NPT connection. Installs on PEX pipe without any tools. Swiveling female NPT connector attaches to a male NPT fitting.Highlights Connect PEX to Threaded Fittings: Easily transition from 1/2" PEX pipe to any 1/2" male NPT fitting or hose in your RV. Swivel Nut for Easy Install: Swiveling 1/2" FPT end lets you attach without twisting or kinking your water line.
Need to connect a 1/2' water line to a threaded fitting in your RV? This Flair-It PEXLock swivel adapter installs fast with clamp rings and pliers so you can get back to enjoying your adventures.Specs Fitting type: PEXLock swivel female adapter Connection size: 1/2" barb x 1/2" female pipe thread (FPT) Compatible pipe: 1/2" PEX, PERT tubing, IAPMO approved polyvinyl tubing Material: Reinforced polyoxymethylene (POM) Maximum temperature: 180 F Maximum pressure: 100 PSI
Need to bend your RV water line around a corner? This PEXLock elbow lets you route 1/2" pipe tight and clean, with leak resistant clamps and no special tools required.Highlights Make Tight Turns Easy: Route your 1/2" water line around corners or obstacles without kinking the pipe. All Plastic, No Corrosion: PEXLock system stands up to hard or acidic water and prevents rust or buildup.
Filters
