Troubleshooting SnapPads That Come Off While Traveling
Updated 09/26/2026 | Published 09/20/2026 >
Question:
Hi, I ordered a set of 9 snap pads about 10 months ago and just installed them this weekend. they were fully snapped on however 2 of them fell off I didnt lose them, but I was also able to pull the other 2 off pretty easily. Im looking for advise on re-installing or replacing them as I dont want to lose them.
asked by: Pete M
Expert Reply:
Hey Pete, thanks for reaching out. If the SnapPads were fully seated but two fell off and the others can be pulled off easily by hand, I’d first double-check that the SnapPad model matches the exact size and shape of your leveling jack feet. When properly matched and installed, they are meant to grip the jack feet tightly and stay permanently attached.
For reinstalling them, inspect the rubber lip for any stretching, tearing, or damage, then clean the jack feet and SnapPads before trying again. If the pads still snap on loosely or pull off easily, I would not travel with them installed since you risk losing them.
What size/shape are your jack feet? Are they all the same size?

Steve
9/22/2026
Like Jesse, I am not sure how these do not work for you. I have had them on three different 5th wheels and never had a problem and towed over 100,000+ miles. You say they came off but did not lose them... That sounds like they never seated completely or got caught on something and were pulled loose. Here is a trick for re-installing them to make sure they seat completely. Take some liquid dish soap and wipe along the edge of the metal foot and also swipe all around the inside edge of the Snapad. This acts as a lubricant when you are using the hydraulics to seat them. It just washes away away and is not harmful to the equipment or environment.

Dan
9/23/2026
I installed the snap pads as instructed and have not had a problem. If I recall correctly, the installation instructions recommended using dish soap on the pad to help them slide on. I did this and they did pop on and have been secure for 2-3 years.
Continue Researching
- Search Results: blue ox tow bar
- Video: Feature Review Towed Car Conversion Kit
- Search Results: 7~way to 6~way coiled adapter cord
- Search Results: blue ox storage bag
- Search Results: flat tow wiring harness
- Search Results: air over hydraulic brakes flat tow brake system
- Shop: Towed Car Conversion Kit - Demco Stay-IN-Play Duo to Air Force One Flat Tow Brake System
- Search Results: phone and tablet cases
- Search Results: generator plug adapters
- Shop: Rubber Wiper Seal with Track for RV Slide Out - Stick On - 15' Long x 3-3/4" Wide
- Shop: Rubber Wiper Seal with Bulb for RV Slide Out - 3/16" Flange - 40' Long x 2-7/8" Tall
- Video: What to Know About the Demco Wireless Coachlink Braking Monitor for Flat Tow Brake Systems
- Shop: Roadmaster Falcon 3HD Tow Bar - RV Mount - 2" Hitch - 10,000 lbs
- Shop: etrailer SD Non-Binding Tow Bar for Roadmaster Direct-Connect Base Plates - RV Mount - 6,000 lbs
- Shop: Reinstall Kit for Demco Stay-IN-Play Duo Flat Tow Brake System
- Shop: Replacement G-Force Controller for Demco Stay-IN-Play Duo Flat Tow Brake System
- Shop: Trailer Hitch
- Q&A: Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Q&A: Comparing Hitch Options On 2024 Silverado 1500 Without Factory Hitch
- Video: An In-Depth Look at the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Q&A: Will Demco Autoslide Have Enough Bed Rail Clearance On 2024 Chevy Silverado 1500
- Shop: Suspension Enhancement
- Article: How to Measure for Trailer Hitch Drop
- Shop: Brake Controller
- Q&A: Parts Needed to Flat Tow 2024 Chevrolet Silverado 1500 Trail Boss
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)

Pete M.
9/21/2026
They are all the same size... 9". 2025 discovery 40m. I am thinking about bolting them on w 1/4-20 1.5" bolts using 4 of the 8 preprinted holes in the foot plates... the comment of not traveling w them installed effectively defeats the purpose of buying them... Thoughts?