Replacement Tekonsha Prodigy P2 Brake Controller For 99 Ford F350

Question

Question:

I have a tekonsha prodigy 2 brake controller in my 99 F350. I need to replace it. When looking at them it looks like all come with custom wiring harness and no universal harness. Its already wired in and I assume the connector at the back of the controller hasnt change so I can simply unplug it and plug new one in.

asked by: Lawrence

0

Expert Reply:

Hi Lawrence!

The Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional # 90885 will include the universal pigtail and would be the one to go with. The Tekonsha connector hasn't changed in a very long time (if it ever has, actually) and your current one will fit just fine. Just unplug it and plug the new controller and you are on your merry way!

How long have you been using your current P2?

expert reply by: Lazer S

0

Lazer S.

9/12/2025

Hey Lawrence, Did the new Tekonsha P2 Brake Controller fit and work well with your setup? I'm curious to know because it could help others who are considering a similar replacement.

Answer 1

There are traditional and standard wiring configurations and that can be frustrating when working with electrical connectors. We try to always remind customers to check wiring for function and not to rely on the color of the wires for that reason.…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Replacement Tekonsha Prodigy P2 Brake Controller For 99 Ford F350

Continue Researching