Are There Any Trailer 7-Way Cables With 6 or 8 Gauge Wire Available

Question

Question:

hi. i buy a bunch of stuff rom you. looking for a 7way harness to repalce the harness on my trailer. but i need that power to be like 8awg maybe even 6awg. biggest i see is 10awg. what might youhave?

asked by: Steve G

0

Expert Reply:

The trailer 7-way cables that we currently offer are going to max out at 10awg so you would need to get just the connector, like part # A7WCB, and wire it yourself with 8awg or 6awg. To protect the wires you can use some 1/2" wire loom # 459075-1 and wrap it all with electrical tape.

expert reply by: Kevin C

0

Answer 1

The Tekonsha Prodigy RF Wireless Trailer Brake Controller doesn't tell us the color coding but does show the corresponding function locations. Based on this, you will use the Bargman 7-Way, RV-Style Connector w/ 6' Heavy Duty Insulated Cable…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hello Jeffrey, Thanks for writing in. Just as long as your current hubs are in good condition, you will be able to use them with electric brakes as well, as long as they are standard 7" brake drums with the correct 4-bolt mounting flange (which…

view full answer...

Are There Any Trailer 7-Way Cables With 6 or 8 Gauge Wire Available

Products Featured in This Question

Continue Researching