Best Aluminum Ramps For Loading Cars Or ATVs Into Trailer

Question

Question:

Did the price change for Aluminum Car Hauler Ramp Set?

asked by: STUART F

0

Expert Reply:

Prices can change at times so it is possible that the Aluminum Car Hauler Ramp Set - 72" x 14-1/2" - 6,000 lbs # 288-07503 has a price tag that differs from when you last saw it. There is also the 48" version that is more affordable as you can see on this link: Aluminum Car Hauler Ramp Set - 48" x 14-1/2" - 6,000 lbs # 288-07501. Perhaps this is the one you were originally looking at. I attached a demonstration video for you to check out.

expert reply by: Andrew N

0

Answer 1

The hook opening of the Gen-Y Hitch Aluminum Loading Ramp Set #325-GH-R72 is two inches wide. I attached a picture that shows where the measurement is taken.

view full answer...

Answer 2

Yes, the Aluminum Car Hauler Ramps #288-07501 do come as a set of two ramps. These ramps are lightweight at just 17 lbs each but have a total capacity of 6,000 lbs so they can handle even large equipment. They also come with safety straps to connect…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Best Aluminum Ramps For Loading Cars Or ATVs Into Trailer

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching