Sidewind Trailer Jack End Cap Replacement

Question

Question:

I have a 2015 Dutchmen Kodiak Express. The trailer jack has no cap. The jack has no markings. It’s a three point attachment , side winds, and needs a circular cap. Outer diameter is a shade under 2.25”, inner diameter is just over 2”. One end has a hole for screw or grease fitting? And other side is notched. Thanks...

asked by: Joseph M

0

Expert Reply:

The most common replacement is the Replacement Cap for etrailer and Ram Swivel Marine Jacks part # MJ-1000B-CP this sounds identical to the description you have given.

expert reply by: Randy B

0

Answer 1

For your Fulton F2 Swing-Up Trailer Jack, Dual 7" Wheels, Sidewind, Bolt-On - 1,600 lbs #F1413020134 part number 9 you referenced is not a replacement option. The outer tube components are not replaceable according to my contact at Fulton. That…

view full answer...

Answer 2

We have a variety of Fulton replacement caps for trailer jacks but I wasn't able to locate what your 0951503-00 looks like even on Fulton's site. With that being said, here are the options that we have: Replacement Round Cap for Standard…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Sidewind Trailer Jack End Cap Replacement

Products Featured in This Question

Continue Researching