Can the 900 lb Dutton-Lainson Hand Winch be Used for a Pop Up Camper

Question

Question:

Does it work for pop up campers and will it work with a cable wire for the pop up camper

asked by: Allysia A

0

Expert Reply:

There really are no limitations as to where you can install the Dutton-Lainson Hand Winch # DL15002 just as long as it isn't a vertical pull. It has a max capacity of 3/16" x 40' when it comes to cable so the best option we have is the 25' Cable # DL24043.

I have attached some review videos for you to check out.

expert reply by: Jon G

0

Answer 1

The charging circuit on a vehicle 7-way style connector, the one that would deliver a maintenance charge to the trailer battery while you tow, is completely separate from the 4-wire brake controller wiring. This trailer charging circuit is usually…

view full answer...

Answer 2

To run a charge line to your battery you will first need to install a 7-Way on your trailer. This can be done using the Epicord 7-Way Molded Trailer Plug with Junction Box #277-000141. The Black wire in the junction box is the one that will carry the…

view full answer...

Answer 3

We have a way you can install a 7-way on your 2015 Mazda CX-5 but not all vehicles have custom fit 7-ways made for them so you'd have to start with the more common 4-way like the part #C56011 which is custom fit for your vehicle. From there…

view full answer...

Answer 4

For a 4-way to 7-way adapter for an application where you would never plan to operate trailer brakes all you need is the part #37185 which allows just the trailer taillight functions to pass through. If you instead do plan to operate trailer brakes…

view full answer...

Answer 5

It sounds like you may have a 7-way trailer connector and a 4-way trailer connector on your truck and only a 4-way connector on your trailer. Is that correct? See the attached picture for examples of each. If this is the case, then this change will…

view full answer...

Answer 6

I do have a couple of solutions for you but you do have a very unique situation so there isn't a perfect solution that is able to address all of your concerns. The best solution is to install a trailer hitch like the Adjustable Width Trailer…

view full answer...

Answer 7

The Curt Hitch Adapter #C45405 will not reduce the tongue weight of your hitch. Many adapters that extend the length will reduce towing capacity based on tongue weight, but this adapter isn't one of them. It will work fine with the Curt TruTrack…

view full answer...

Answer 8

The best storage cover for your 2023 Coachman Clipper Express 9.0 is the Classic Accessories PolyPro III Deluxe #CA80199. This is designed around R-Pod trailers but yours is close enough in size and body style that this will fit great!

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Can the 900 lb Dutton-Lainson Hand Winch be Used for a Pop Up Camper

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching