Center-To-Center Measurement For Mounting Holes On Bulldog Collar-Lok Coupler

Question

Question:

I am looking for a replacement but I need to know the bolt hole dimensions from center to center of each hole. Thank you

asked by: Bill

0

Expert Reply:

I went to the warehouse and measured the distance between the mounting holes on the Bulldog Collar-Lok Coupler, part # BD028585.

The center-to-center distance is 2 inches. This coupler mounts in a 3 inch channel bracket and is 10 inches long. The ball size this coupler is designed for is 2-5/16 inches.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

Just like the tires for your trailer, the combined load capacity of your wheels should at least match the loaded weight of your trailer. Ideally though they will have a larger combined capacity than your trailer weight to provide a nice safety…

view full answer...

Answer 2

Load range capacity varies based on the tire size and brand, so without knowing either, it's hard to say. For example, a load range D tire in size 145/80-12 has an average capacity of 1,220 lbs, while a load range C tire in size 185/80-13 has an…

view full answer...

Answer 3

The inside mounting channel width is just under 2 inches, while the outside width (as you mentioned), is just under 3 inches, designed to fit into a 3 inch wide channel, like #BDAC5000300. The overall length is 10 inches, as shown in the attached…

view full answer...

Answer 4

In general for trailer clearance lights you want to have red clearance lights that face the rear of the trailer and then amber that are on the sides or face the sides. I attached a link to a page that has all of the clearance lights we carry as…

view full answer...

Answer 5

The recommended clearance needed between the trailer fender and trailer tire is 3-4" from the top of the tire to the bottom of the fender. That said, it would be best to mock this up beforehand and see which location works best with your setup.…

view full answer...

Answer 6

The Timbren Axle-Less Trailer Suspension System - Straight Spindle Only - 3,500 lbs #ASR3500S05 has a deflection of 1-3/4 inches. I've attached a photo to assist. We recommend 4 inches above the tire in most cases for fender mounting to account…

view full answer...

Answer 7

Hey Alan, yes we do have locks for the Demco EZ latch coupler #DM14040-81 that you referenced with the InfiniteRule Lock part #IR66FR.

view full answer...

Answer 8

Hi Christian; the Weigh Safe Flap Jack Folding RV Stabilizing Blocks #WS88ER can be used in the folded position. They have the same 6,000 lb capacity when they're collapsed.

view full answer...

Answer 9

Hey Daryl, I checked with Weigh Safe and the Flap Jacks like the part #WS88ER are not designed to be stacked. Are you in need of something 10 inches tall?

view full answer...

Answer 10

The Advent Air Rooftop RV Air Conditioner #ACM135C does not require a mounting bracket to install, just a 14-1/4" x 14-1/4" opening and a framed with 3/4" lumber, as you can see by the accompanying cut out I added from the linked…

view full answer...

Answer 11

Based on your axle info the correct bearing kit would be the part #BK3-310 for a kit that includes both bearings #LM67048 and #25580 as well as a grease seal.

view full answer...

Answer 12

The best way to power the interior lights in your trailer is with its own independent battery. You will not want to use the breakaway battery. The breakaway battery is only designed to operate the breakaway and will drain extremely quickly,…

view full answer...

Center-To-Center Measurement For Mounting Holes On Bulldog Collar-Lok Coupler

Featured Help Information

Miscellaneous Media

Continue Researching