Installing P3 Brake Controller on 2014 Yukon Denali

Question

Question:

Requesting your advice on installing the Tekonsha P3 91095 on our 2014 GMC Yukon Denali. The wiring harness has 4 wires dark blue-AUX, red/black-BATT, light blue/white-CHMSL, white-GRND. Not sure whats under the hood that needs connected. Probably a lot easier than Im making it! Thanks

asked by: Jay O

1

Helpful Expert Reply:

I would be happy to help! I attached a help article for you to check out that details exactly how the P3 Brake Controller part # 90195 will install in your 2014 GMC Yukon, but basically here is how the wires will attach.

Red/Black from Yukon to Black of the Brake Controller. This is the Battery/Power Circuit
White to White. This is the Ground
Light Blue/White from Yukon to Red of Brake Controller. This is Brake Light Signal Circuit.
Dark Blue from Yukon to Blue of Brake Controller. This is Brake Output to Trailer brakes
Orange of the Yukon is not used.

expert reply by: Jameson C

1

Gary

6/28/2024

Do these wiring instructions work on a 2014 Yukon Denali with a factory integrated trailer brake controller? My new boat trailer is electric-over-hydraulic and the ITBC on the 2014 and earlier Yukons apparently doesn’t work with those. Much appreciated!

Jameson C.

7/1/2024

@Gary The wiring colors should be the same that run to your ITBC so you can swap them to a new controller like the P3 part # 90195 that is EOH compatible.

Answer 1

For your 2019 GMC Yukon XL I highly recommend the Tekonsha Prodigy P3 Trailer Brake Controller #90195. This is an excellent proportional controller that is well known both for its reliability and ease of use. What sets this unit apart from its peers…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Installing P3 Brake Controller on 2014 Yukon Denali

Featured Help Information

Miscellaneous Media

Continue Researching