This fitting replaces the 1/4" pushlock to male 1/8" NPTM fitting for your Demco Air Force One supplemental braking system. Straight design allows for streamlined routing of your air line.
Replaces the bent handle pin and clip for your Demco Recon Gooseneck to 5th wheel hitch adapter base (DM6021). Secures the coupler into the base platform.
Restore safe towing with this 2" ball coupler for your Demco DA70 actuator. Replaces worn or damaged coupler and bolts directly to the actuator housing.
Bolt this locking plate onto your Lippert Helux pin box to prevent the king pin from rotating inside your Demco Autoslide fifth-wheel trailer hitch. Hardware included.
Replaces the fuse holder for your Demco Stay-IN-Play Duo (SM99251 or SM99243) or Air Force One (9599007, 9599019, 9599020, or 9599021) supplemental braking system.
Replaces the 2-5/16" coupler for your Demco Recon Gooseneck to 5th wheel hitch adapter base (DM6021). Provides the attachment point for the gooseneck ball in your truck bed.
Lost a fender on the road or cracked it backing into a tight spot? This replacement passenger's-side fender assembly gets your Demco KarKaddy SS or KarKaddy 3 tow dolly looking sharp and road-ready again.
Lost a fender on the road or cracked it backing into a tight spot? This replacement driver's-side fender assembly gets your Demco KarKaddy SS or KarKaddy 3 tow dolly looking sharp and road-ready again.
Square tube welds onto your trailer. Works with 4" width inner tubes (sold separately). Pairs perfectly with the eZ-Latch gooseneck coupler DM43KV (sold separately).
Add extra strength where your Demco cable anchor bolts to the firewall. This steel plate reinforces thin firewalls for Air Force One or Stay-IN-Play Duo installs, keeping the anchor secure.
Moving your 5th-wheel hitch to a new truck? This replacement hardware kit lets you reinstall your Demco universal above-bed base rails (DM6701) with all-new bolts, nuts, and washers - giving you a rock-solid fit for safe, confident towing.
Replace the lost or damaged cable anchor in your Demco Stay-in-Play DUO or Air Force One system. Includes set screw to secure the cable in place and restore your systems function.
Replaces a worn or missing ramp bushing on your Demco Kar Kaddy SS tow dolly. This bushing ensures proper spacing, allowing the ramp to tilt up for storage and secure in lowered position for loading.
Round tube welds onto your trailer. Works with 4" diameter inner tubes (sold separately). Pairs perfectly with the eZ-Latch gooseneck coupler DM73KV (sold separately).
Your trailer's wired right, but the brakes still won't fire. If your factory controller doesn't recognize your electric-over-hydraulic actuator, this adapter sends the signal it needs so the brakes activate, no rewiring required.
This oversized mounting plate covers gaps or holes when installing a Coleman-Mach digital wall thermostat. It provides a clean, finished look and works with models 9420-381 and 9420-382.
Restore connectivity between your switch panel and RV generator with this 10-foot Cummins Onan adapter harness. Designed for use with remote start/stop control panels on HGJBB, KY, and HGJAx model generators.
You're replacing your RV's thermostat and want something easy and reliable. This single-zone analog unit gives you simple heating and cooling control without digital menus.
You're swapping out your RV's AC and need a distribution box to match. Open the louvers for cool air directed straight into the cabin, or close them to push air through existing ducts. Includes a filter that pops out for a quick rinse.
You're replacing your RV's AC and need a non-ducted ceiling assembly with built-in controls. This unit adds front and rear airflow dampers, pop-out filters, and heat strip prep. Designed for Coleman-Mach systems. Other parts required.