Replace the neo angle skylight on your RV or camper roof. 27" Wide x 14-1/2" long flange fits a 24" wide x 12" long angled cutout. Smoke-colored polycarbonate plastic reduces light and UV rays. Includes sealant for installation.
Customize your Dometic TRT tent camping experience with this spacious awning. Awning clips onto your rooftop tent and inflates within minutes, providing both shade or a privacy room. Designed for standard height cars. Poles and carry bag included.
Upgrade your RV kitchen or boat galley with this premium, Italian-made mini fridge and freezer. Sleek built-in design installs into shallow or tight spaces to save space whether your adventure takes you by land or sea.
Bolt this locking plate onto your Lippert Helux pin box to prevent the king pin from rotating inside your Demco Autoslide fifth-wheel trailer hitch. Hardware included.
Get some added traction with these slip-resistant and marine-grade step treads. These step treads are designed specifically for the MORryde Gen II StepAbove 4-step with 23-1/2" treads. Applies quickly and easily with adhesive backing.
This is a rave-worthy upgrade for your RV. It extends far enough for you to grab hold before taking the first step up, and it folds flat without obstructing your door or slide out. Feels sturdier and looks better than what you're used to.
Swap between all your different hitch accessories with this adapter. It converts a 3" receiver into a 2-1/2" or 2" receiver. Includes pin and clip. Not for towing; use for hitch accessories only.
Taking bunk carpet off can be a pain. These composite panels will install right over it. Their shape directs water and grit away from your boat hull. Glides are slick to let you load your boat in shallower water.
Go the extra mile with your Tow & Stow ball mount - from the field to the job site, back to weekends camping with the family - by adding this 2-tang clevis. Just attach it to your ball mount's shank with your existing pins.
These edge glides give you a smooth transition from the ground onto your ramps or trailer. Glides minimize friction for snowmobiles but include traction knobs so you can still walk on them safely, or load up your favorite offroad toy.
Connect up to 3 propane appliances to your RV's LP gas line with this simple plug and go manifold - no frustrating teflon tape needed! Enjoy the flexibility of powering up your appliances from one central point while minimizing safety risks.
You pull off the trail, ready to make camp, and the sun is blazing. In minutes, this awning swings out and secures to cast 270 degrees of shade and shelter. Now, the crew can kick back and even if the wind and rain roll in, everyone stays covered.
Need a tough, reliable connection from your actuator to the main brake lines? The non-stick polymer core locks in pressure, while braided stainless steel fends off road debris. No ballooning, no leaks, just reliable stopping power.
2-1/2" x 2-1/2" Receiver tube is designed for fabricating a custom hitch when a receiver isn't available. Weld-on installation. Tube is 12" long. Raw steel construction is durable.
Replaces the #05 rubber shear spring on MORryde's rubber pin boxes for trailers between 14,001 - 18,000 lbs GVWR. Helps absorb and dampen road shock, vibration, and reduces chucking. Installs on the skid pad with your existing hardware.
Required in most states, a safety cable acts as a backup if your trailer becomes disconnected from your tow vehicle. cables to your trailer's coupler, and then hook the S-hooks to your hitch.
Radial tire has 14-ply rating and 4,410-lb max load at 110 psi. 16" x 6" Steel wheel has 8 on 6-1/2 bolt pattern. 1-Year No Excuses Guarantee on tire. Complimentary roadside assistance included.
Radial tire has a 16-ply rating and a 4,806-lb max load at 125 psi. 17-1/2" x 6-3/4" Hub-piloted solid center wheel has an 8 on 6-1/2 bolt pattern and +0.19" offset.
Use this adapter fitting to transition your 1/2" PEX pipe to a fresh-water line with a 1/2" NPT connection. Installs on PEX pipe without any tools. Swiveling female NPT connector attaches to a male NPT fitting.
These bunk wrap endcaps protect the ends of your bunks. Pair with Caliber bunk wraps for a clean, finished look. Comes in a bulk box of 24, so it's great for multiple bunk replacement projects or stocking your marine supply store.
Filter Results
