New Arrivals

Lost a fender on the road or cracked it backing into a tight spot? This replacement passenger's-side fender assembly gets your Demco KarKaddy SS or KarKaddy 3 tow dolly looking sharp and road-ready again.

• Accessories and Parts
• Trailers
• Tow Dolly Parts
• Fenders
• Demco

Square tube welds onto your trailer. Works with 4" width inner tubes (sold separately). Pairs perfectly with the eZ-Latch gooseneck coupler DM43KV (sold separately).

• Accessories and Parts
• Gooseneck Coupler
• Outer Tube
• Demco

Add extra strength where your Demco cable anchor bolts to the firewall. This steel plate reinforces thin firewalls for Air Force One or Stay-IN-Play Duo installs, keeping the anchor secure.

• Accessories and Parts
• Flat Tow Brake System
• Hardware
• Plates
• Demco SBS

Moving your 5th-wheel hitch to a new truck? This replacement hardware kit lets you reinstall your Demco universal above-bed base rails (DM6701) with all-new bolts, nuts, and washers - giving you a rock-solid fit for safe, confident towing.

• Accessories and Parts
• 5th Wheel Hitch Rails
• Hardware
• Universal
• Demco

Replace the lost or damaged cable anchor in your Demco Stay-in-Play DUO or Air Force One system. Includes set screw to secure the cable in place and restore your systems function.

• Accessories and Parts
• Flat Tow Brake System
• Hardware
• Anchors
• Demco SBS

Replaces a worn or missing ramp bushing on your Demco Kar Kaddy SS tow dolly. This bushing ensures proper spacing, allowing the ramp to tilt up for storage and secure in lowered position for loading.

• Accessories and Parts
• Trailers
• Hardware
• Bushings
• Demco

Replace a worn or damaged clevis on your first-generation Demco Excali-Bar tow bar (9511006) with this exact-fit part. Built to keep your tow bar securely attached to your base plate, it restores the solid link your flat towing setup relies on.

• Accessories and Parts
• Tow Bar
• Clevis
• Excalibar
• Demco

If you're tired of your trailer brakes locking when you back up, this hand activated reverse lockout stops the surge actuator from applying the brakes. It installs directly on any Demco DA75 actuator with no electrical hookup required.

• Accessories and Parts
• Brake Actuator
• Hydraulic Drum Brakes
• Reverse Lockout
• Demco

Demco's eZ-Latch coupler latch is now available for your gooseneck trailer! This gooseneck coupler head assembly welds onto the stem of your trailer.

• Accessories and Parts
• Gooseneck Coupler
• Head
• Demco

Replaces the Command Center smart tablet for your RVibrake 3 portable flat-tow braking system (50MG0004).

• Accessories and Parts
• Flat Tow Braking System
• Controllers
• Tablet
• CURT

Replace a damaged or worn spring bar on your Curt TruTrack 2P system with this forged steel bar. Designed for 5,000-lb to 8,000-lb setups only (17599). Restores sway control and load leveling for safer, more stable towing.

• Accessories and Parts
• Weight Distribution Hitch
• Spring Bars
• Sqaure Bar
• CURT

Install your Curt electric trailer brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your controller and then plug the other end into the built-in port beneath your vehicle's dash.

• Accessories and Parts
• Trailer Brake Controller
• Wiring Adapter
• Plugs into Brake Controller
• Vehicle Specific
• CURT

For heavy-duty applications that require cable, this steel winch cable has a break strength of 4,200 lbs and a working load limit of 1,400 lbs.

• Accessories and Parts
• Electric Winch
• Trailer Winch
• Cables and Straps
• 3/16 Inch Diameter
• 4200 lbs
• Wire Rope
• CURT

Replaces the heavy-duty L-pins and clips from your Curt TruTrack 2P trunnion weight distribution system with integrated active sway control (17355) or support brackets (17517, 17518, and 17519).

• Accessories and Parts
• Weight Distribution Hitch
• Pins and Clips
• CURT

Your trailer's wired right, but the brakes still won't fire. If your factory controller doesn't recognize your electric-over-hydraulic actuator, this adapter sends the signal it needs so the brakes activate, no rewiring required.

• Accessories and Parts
• Brake Actuator
• Hydraulic Drum Brakes
• Disc Brakes
• Adapters
• Deutsche Hydrapro

This oversized mounting plate covers gaps or holes when installing a Coleman-Mach digital wall thermostat. It provides a clean, finished look and works with models 9420-381 and 9420-382.

• Accessories and Parts
• RV Air Conditioners
• Thermostat
• Mounting Plates
• Coleman-Mach

Restore connectivity between your switch panel and RV generator with this 10-foot Cummins Onan adapter harness. Designed for use with remote start/stop control panels on HGJBB, KY, and HGJAx model generators.

• Accessories and Parts
• Generators
• Wiring Harness
• Cummins Onan

You're replacing your RV's thermostat and want something easy and reliable. This single-zone analog unit gives you simple heating and cooling control without digital menus.

• Accessories and Parts
• RV Air Conditioners
• Thermostat
• Black
• Coleman-Mach

You're swapping out your RV's AC and need a distribution box to match. Open the louvers for cool air directed straight into the cabin, or close them to push air through existing ducts. Includes a filter that pops out for a quick rinse.

• Accessories and Parts
• RV Air Conditioners
• Air Distribution Box
• White
• Coleman-Mach

You're replacing your RV's AC and need a non-ducted ceiling assembly with built-in controls. This unit adds front and rear airflow dampers, pop-out filters, and heat strip prep. Designed for Coleman-Mach systems. Other parts required.

• Accessories and Parts
• RV Air Conditioners
• Air Distribution Box
• White
• Coleman-Mach

You're replacing your RV's AC and need a ceiling assembly that puts you in control. This non-ducted air distribution box has built-in knobs, adjustable louvers, and a pop-out filter. Designed for Coleman-Mach systems. Other parts required.

• Accessories and Parts
• RV Air Conditioners
• Air Distribution Box
• White
• Coleman-Mach

Turn your Coleman-Mach underbunk AC unit into a true comfort system. This kit adds a thermostat, remote, ducting, vents, and hardware so you can control temps and route your airflow exactly where you need it.

• Accessories and Parts
• RV Air Conditioners
• Remote Control
• Thermostat
• Coleman-Mach

You're replacing your RV's thermostat and need a digital controller that works with your Coleman-Mach single-zone system. This is the thermostat only, but you can pair it with a compatible rooftop AC and ceiling assembly to finish your setup.

• Accessories and Parts
• RV Air Conditioners
• Thermostat
• Black
• Coleman-Mach

Replace the worn or non-working switch panel on your Cummins Onan generator. This panel lets you start and stop your gas or LP generator from a central location and works with select HGJBB, KY, and HGJAx models.

• Accessories and Parts
• Generators
• Switch Panel
• Cummins Onan