Round tube welds onto your trailer. Works with 4" diameter inner tubes (sold separately). Pairs perfectly with the eZ-Latch gooseneck coupler DM73KV (sold separately).
If you're tired of your trailer brakes locking when you back up, this hand activated reverse lockout stops the surge actuator from applying the brakes. It installs directly on any Demco DA75 actuator with no electrical hookup required.
Your trailer's wired right, but the brakes still won't fire. If your factory controller doesn't recognize your electric-over-hydraulic actuator, this adapter sends the signal it needs so the brakes activate, no rewiring required.
Restore connectivity between your switch panel and RV generator with this 10-foot Cummins Onan adapter harness. Designed for use with remote start/stop control panels on HGJBB, KY, and HGJAx model generators.
You're swapping out your RV's AC and need a distribution box to match. Open the louvers for cool air directed straight into the cabin, or close them to push air through existing ducts. Includes a filter that pops out for a quick rinse.
You're replacing your RV's AC and need a non-ducted ceiling assembly with built-in controls. This unit adds front and rear airflow dampers, pop-out filters, and heat strip prep. Designed for Coleman-Mach systems. Other parts required.
You're replacing your RV's AC and need a ceiling assembly that puts you in control. This non-ducted air distribution box has built-in knobs, adjustable louvers, and a pop-out filter. Designed for Coleman-Mach systems. Other parts required.
You're replacing your RV's thermostat and need a digital controller that works with your Coleman-Mach single-zone system. This is the thermostat only, but you can pair it with a compatible rooftop AC and ceiling assembly to finish your setup.
Replace the worn or non-working switch panel on your Cummins Onan generator. This panel lets you start and stop your gas or LP generator from a central location and works with select HGJBB, KY, and HGJAx models.
Replace 2 worn or damaged backing plates on your single-axle trailer fender. Backing easily blocks water and road debris from hitting the side of your trailer.
Coupler repair kit contains all needed replacement parts for your CE Smith straight-tongue coupler with a 3,500-lb or 5,000-lb capacity, except for the coupler housing.
If you're tired of steel brackets rusting out on your boat trailer, try this aluminum bracket. It's lightweight, durable, and won't rust, so your tail lights stay mounted season after season no matter where you launch.
This towing safety flag is ideal for your kayak, SUP, or anything else you want to tow and draw attention to. Made of Oxford fabric and nylon webbing, so it holds up for the long haul.
If you're tired of steel brackets rusting out on your boat trailer, try this aluminum bracket. It's lightweight, durable, and won't rust, so your tail lights stay mounted season after season no matter where you launch.
If you're tired of steel brackets rusting out on your boat trailer, try this aluminum bracket. It's lightweight, durable, and won't rust, so your tail lights stay mounted season after season no matter where you launch.
Bring your guide-on back to life with this genuine replacement post for your 22" pontoon post guide-on setup. Made from durable, white PVC, it drops right onto your existing brackets to get you back on the water faster.
Replace 1 worn or damaged backing plate on your single-axle trailer fender. Backing easily blocks water and road debris from hitting the side of your trailer.
The breeze is perfect, but now a rip threatens your bug-free night. With these patches in your pack, you fix the hole in seconds and relax, knowing nothing will crawl in as you drift off to sleep.
Too long for a short hose, too tight for a 6-footer? This 3' line gives you the extra length to make the connection without looping or straining. It's perfect for offset runs, frame tabs, and foldaway hinge setups.
Need a no-nonsense lug nut? This zinc-plated open-end acorn lug nut gives you a secure fit without the fuss. Built tough to resist rust and wear, it won't trap moisture and works great with longer wheel studs.
Replace a missing or damaged caliper bracket on your DeeMaxx 6K disc brake assembly. Designed for use with integral and slip-over rotors, this bracket features DeeMaxxs corrosion-resistant MAXX coating for long-lasting durability.