Most Popular Side Window for Honda Accord

Arrived timely. Product undamaged. Worked perfect. Thanks eTrailer.

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

I just finished installing the Weathertech Air Deflectors and it was simple! The included instructions made the install a breeze (no pun intended), taking me less than 10 minutes from start to finish. They look great but I haven't road tested them yet.

Installation was easy. Just view the video posted and take you time. They look great on my SUV. I like them better than the ones that attach to the paint.

Easy as pie. The you tube video was great help. Worked like a charm on my 2015 Honda pilot. Took me about an hour from start to finish.

The rear Rain Guards went on easy. The front was a pain and would not seat properly to allow the window to go up freely. It didn't help that Putco decided to send a QR code to get instructions although install was pretty straight forward since they will only fit one way. The QR code didn't go straight to the site for the instructions. I had to jump through too many hoops and never got there. Whatever happened to just putting the instructions in the box? The window still contacts the front end of the guard. Perhaps it will seat if I leave the window up for a while. Instructions would probably have helped. Packaging was poor as well and although they weren't damaged, I have seen how delivery drivers handle packages and this could have been a problem.

After looking around for a few weeks for window visors I decided to give these a try for my 2011 Silverado 1500. The well packed shipment arrived in within a few days, and I have to admit I was a little skeptical when I first opened it. The visors themselves and the adhesive strips seemed a little thin and danity. I dry-fitted everything before removing the tape backing to get an idea of how they attach. Total install took 15-20 minutes. It has been a year, and they function as advertised, and still look good (they've held up to several pretty aggressive automatic car washes). These allow you to keep the window cracked in hot weather without worrying about a passing rain drenching your interior. These are visors, not rain deflectors.

Click to Enlarge

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

Forget the Putco, order the WeatherTech for a better, more secure installation. Lesson learned. I ordered these figuring to save a little money. Not worth it in the long run.

Great product, installation was a breeze. Was sent two left rear window deflectors, called e trailer and they took care of it right away. Top notch customer service!

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

The front rain guards fit my 2023 Passport perfectly. The rears weren't setting correctly in the window seal and neither rear window would roll up completely. Also, when I remove the two rear rain guards, I noticed the thinnest part, which is supposed to go between the window seal and the glass had broken in use. I have no patience for this, so I threw the rears in the trash. In retrospect, I'd have have rated these a 5 if I'd only purchased the fronts.

paid the little extra to go with these well made and excellent fitting window vents as other "stick ons" just dont last. I bought from etrailer as they track shipping and assure delivery. very pleased! highly recommend WeathTech & etrailer

Click to Enlarge

Click to Enlarge

Click to Enlarge

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

The rear Rain Guards went on easy. The front was a pain and would not seat properly to allow the window to go up freely. It didn't help that Putco decided to send a QR code to get instructions although install was pretty straight forward since they will only fit one way. The QR code didn't go straight to the site for the instructions. I had to jump through too many hoops and never got there. Whatever happened to just putting the instructions in the box? The window still contacts the front end of the guard. Perhaps it will seat if I leave the window up for a while. Instructions would probably have helped. Packaging was poor as well and although they weren't damaged, I have seen how delivery drivers handle packages and this could have been a problem.