Trailer Brake Controller Specs:
Features:
...reach on the front of the module, great for stopping sway or controlling your trailer's momentum in emergencies. Push the slide-bar to activate the trailer's brakes and brake lights without you...
Installation Notes:
You need item ETBC7 ($128.85) to install your controller.
You may also need a 4-Flat connector to complete your wiring.
Tech Tip:
An additional stop light switch, RM-751439, may be necessary for installation as this vehicle's stop light switch does not have a cold side to tap into. (sold separately).
More Information >Trailer Brake Controller Specs:
Features:
...Brake controller activates trailer brakes with preset intensity Adjustable power output lets you select the amount of braking force Simple thumbwheel lets you change setting LED indicator
Installation Notes:
You need item
ETBC7
($128.85) to install your controller.
You may also need a 4-Flat connector to complete your wiring. Tech Tip: An additional stop light switch, RM-751439, may be necessary for installation as this vehicle's stop light switch does not have a cold side to tap into. (sold separately).
Videos
for Trailer Brake Controller
Help Articles
for Trailer Brake Controller
Expert Answers
for Trailer Brake Controller
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.
view full answer...The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we…
view full answer...The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…
view full answer...In order to install a brake controller on a dump truck you'd first need to start with a 4-way trailer connector and then…
view full answer...You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…
view full answer...The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…
view full answer...On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…
view full answer...The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you,…
view full answer...For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…
view full answer...