The Replacement Glass Oven Door for Furrion 2-in-1 Range Oven # 715326 for the Furrion 2-in-1 Range Oven with Glass Cover FSRE17SABL, which is no longer available is actually slightly different than the:
-Replacement Stainless Steel Oven Door for Furrion 17" Ovens # FR52FR.
This door measures 21-3/8" wide, 11-3/4" tall, is 1-1/4" thick. With this being 1/8" smaller than your existing door, it is not confirmed to fit, however if you're able to let me know what Furrion Range Oven you have,... view full answer...
Each of the Furrion tankless water heaters measure 12-5/8" wide x 12-5/8" tall x 19-1/4" deep, so that is the size the compartment needs to be. As for the door, there may be trimming needed, depending on the size of the door you have now and the heater you get. Generally some type of trimming is needed as the doors on different models aren't universal sizes. So you need to measure your current door size and go with the Furrion heater that has the closest dimensions.
- 16" x 16" Door: Furrion... view full answer...
Scissor jacks like the Ultra-Fab Ultra Scissor Jacks # UF48-979002 you were looking at are designed more for stabilization and less for leveling the trailer because they aren't really designed to hold the weight of the trailer off the ground. Even though you won't be fully lifting the trailer I still recommend getting close to the GVWR of your trailer. The GVWR listed for your 2019 Grand Design Imagine 2250RK is 6,995lbs so with four scissor jacks you could switch to a lower rated option... view full answer...
Appreciate all of that info, as it's exactly what is needed to get your 2018 Grand Design Imagine 2600RB travel trailer the correct bearings and seal. Since you have a 3,500 lb Lippert axle, the right bearing kit is the following:
- Hub Bearing Kit # BK2-100
The # BK2-100 includes the bearings, races, and seal for one hub, so you'll need two per axle. Then if you need grease I recommend the Lubrimatic # L11380 and for a Bearing Packer use part # ALL647646. view full answer...
The Adco SFS AquaShed RV Cover # 290-52245 you were looking at will fit your 2019 Grand Design Imagine 2500RL. The pictures and video only show that middle panel open but these covers have multiple zippered panels, including one at the rear on the passenger side. This will allow you to access your primary door with the cover on. view full answer...
Since you measured your springs with weight on them I am going to recommend a couple of different length springs as replacements. You will want to verify how long your springs are without weight on them before purchasing. The compression caused by the full weight of your trailer will easily stretch them out around 1" if not more. It is recommended to change both sides if you are replacing suspension components.
24-7/8" Long - Item # e76SR
25-1/8" Long - Item # e47SR
I highly recommend... view full answer...
I can help you determine the right replacement double-eye leaf springs for your 2022 Grand Design Imagine 3250BH, though there isn't any information about the specific ones you need. It's pretty easy to find though, as all you need to do is measure your current leaf springs from center-to-center of the spring eyes.
Leaf springs also flatten a bit over time, so you should go with ones that measure a bit shorter than what you currently have. For example, since you mentioned having a 5,100... view full answer...
So with the Go Power Industrial Pure Sine Wave Inverter Charger # 34275013 as the primary source, what you will do is wire the shore power to Input 2 and the Inverter to Input 1 on the Furrion Automatic Transfer Switch - 50 Amp # F50ATS. view full answer...
The SoftStartRV Soft Start for RV AC Units - Qty 1 # SSR54FR is designed to be a universal fit part and will work with your Furrion AC unit. view full answer...
I do recommend also adding the SumoSprings Trailer Helper Springs # TSS-107-40 on your 2021 Grand Design Imagine 2400BH. These will help to absorb additional road shock the MORryde Shock Absorbing Suspension Equalizers # MR27ZR might not. They also provide stability to the suspension which helps to reduce bouncing and reduce body roll. You will need to ensure you have 5-5/16" to 6-1/2" between the trailer frame and the leaf spring u-bolt plate for the SumoSprings to fit properly. Be sure... view full answer...
To replace the bearings on a Lippert 3,500 lbs axle you will need the outer bearing item # L44649 inner bearing item # L68149. We do have a kit that has the necessary races, seals, and bearings. It is the Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles - 3,500 lb with #84 Spindle item # BK2-100. You will need one of these kits per hub. I have attached an installation video below.
To remove your old seals you will want the Seal Puller item # PTW1219. view full answer...
The amount of space needed is going to vary depending on the spring that you use. If you use the Timbren Trailer Suspension Enhancement System Light-Duty Trailers 1,000 lbs # TTRA1702, those springs are only 2-3/4" tall so you can get away with fairly minimal clearance.
The other option would be the SumoSprings Trailer Helper Springs w/ Line Relocation Bracket - Single Axle - 3K to 5K - Underslung # TSS-106-40 for underslung axles or the SumoSprings Trailer Helper Springs w/ Line Relocation... view full answer...
I do have an option for you but we no longer carry the Aluminum Cheetah Trailer Wheel part LHCH1566SMF. That said, we have plenty of other options in the same size, bolt pattern, and material. The Aluminum Lynx Trailer Wheel part # LHSL311 for example is a 15" diameter x 6" wide wheel with 6 on 5-1/2" bolt pattern made of aluminum.
I have attached our full list of similar wheel options below as well. view full answer...
This will not be an issue for mounting the LED Trailer Tail Light with License Bracket # 328-003-81LBM1 on your 2018 Grand Design Imagine Travel trailer.
The light bracket that mounts to the trailer has tabs on the back with an outer ring to leave a gap between where the wiring leaves the housing and where it will go into the trailer. This gap will allow the wiring to travel behind the light housing into the trailer for the connections.
Be sure to use some Silicone Sealant # 0160297... view full answer...
According to the information I could find on your 2022 Grand Design 2500RL it comes with 3,500LB Dexter axles. This will use the Grease Seals # RG06-050 for one axle. We also have the Bearing Kit # BK2-100 which includes the bearings, races, and grease seal for one hub. view full answer...
The Lippert AP Kit item # LC52SV has 3-1/8" shackle straps. For a comparable option that will work with Road Armor Shock Absorbing Equalizer item # LC696740 you will want that MORryde Suspension Upgrade Kit for Tandem Axle Trailers item # MR76ZR. view full answer...
Yes, the Bearing Kit for #84 Spindles part # BK2-100 is correct for a 2018 Grand Design Imagine. This is actually the correct bearing kit for all sub models that use the "120091" 3,500 Lb Axle such as the 2800BH or 2600RB for example. If you want to replace the entire hub/drum, we have the etrailer Trailer Hub and Drum Assembly part # AKHD-545-35-EZ-K if you have a 5 on 4-1/2" bolt pattern or part # 84656UC3-EZ if you have a 6 on 5-1/2" bolt pattern. view full answer...
Yep, you got it; the correct electric brakes for your 2020 Grand Design Imagine 2670MK travel trailer are the following:
- Dexter Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 4,400 lbs # K23-462-463-00
These come with the mounting hardware so you're set there, but they are manually adjusting brakes so if you don't have one you'll also need the Brake Adjustment Spoon for Drum Brakes # W80630. view full answer...
It sounds like you're looking for the Lippert Replacement 500:1 Motor for Electric In-Wall RV Slide-Out System part # LC287298 which is a 500:1 in-wall slide-out motor. If your existing motor looks the same as this and has the same 500:1 rating then it's likely a direct replacement. That said, the only way we can look this up for you would be with the part/model number of your existing slide-out motor. We cannot look this up using the make and model of the trailer unfortunately. view full answer...
Go To Results