Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Upgrade a heavy cargo, livestock, or equipment trailer from manual cranking with a self-contained 12K hydraulic jack. The integrated 12V pump, keyed control, mounting hardware, and 24" of lift give you a complete powered setup.
Heavy cargo, livestock, and equipment trailers can put enough weight on the tongue to make a manual landing-gear jack a chore every time you hitch or unhitch. This Bigfoot system gives you 12,000 lbs of hydraulic lifting capacity and 24" of lift, letting the onboard pump handle raising and lowering the trailer.
It is a true single-point setup with one jack and one hydraulic power unit, so you are not tying the jack into a separate trailer hydraulic system. The pump, reservoir, and hydraulic connections stay together at the front of the trailer, while the 10" x 10" pivoting foot helps maintain solid contact when the ground is not perfectly level.
The kit includes the mounting brackets and hardware, hydraulic line and fittings, battery cable, 80-amp circuit breaker, and weather-resistant keyed control needed to build the powered setup. You supply a 12V battery and slightly less than 3 quarts of Dexron III ATF.
The system calls for at least 4-gauge battery cable, and the pump assembly needs a solid ground through its steel mounting or a separate frame ground. Once wired, the magnetic control can stick to a steel trailer surface while you extend or retract the jack.
The pump assembly can also be relocated if your trailer layout calls for a different mounting position; longer hydraulic hoses are required and sold separately. This version uses Bigfoot's standard pump and does not include a built-in manual override, so the jack depends on the 12V electrical system for operation.
The adjustable B-brackets are designed around trailer frame sections from about 3-5/8" to 5-1/2" wide. They can bolt through a vertical bulkhead frame section, or the jack can be mounted directly to the frame when your trailer layout calls for it. Bolt-on does not mean every trailer already has matching holes, so compare the mounting area before installation and plan to drill where necessary.
You should set the jack so you have at least 8" to 10" of ground clearance with the trailer at ride height. Mounting hardware is included, but the supplied bolts may not be long enough for every frame thickness, so verify the trailer before you start the install.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi, everyone. Steven here with etrailer. Today we're taking a look at our Bigfoot hydraulic jack. It's a single pump, single jack rated at 12,000 pounds of lift capacity. Now, folks, this is gonna be a heavy-duty style jack. It's very versatile, meaning you could put it on cargo, livestock, heavy equipment, construction trailers, even bumper pull or goosenecks that need that heavy-duty rating.
And what I like about this is you're gonna get the complete setup in one package. So you have the jack, you have the reservoir and everything, the pump included. You have a magnetic remote, and of course you have the brackets and bolts, to mount this on your trailer without having to worry about welding. And I wanna start off with the remote while I have it here. As you can see, you have a key, you can lock this, that way no one can come and mess with your jack.
It is magnetic on the back so you can put it on your trailer frame, put it on the box here. You got plenty of length of wires to go where you need to. Also, before I go too further in this, you can actually unbolt the main power unit box here and everything, and move it somewhere else remotely if you don't want it where it's at. Just keep in mind, you'll probably have to purchase longer hydraulic hoses because these are the length that comes with it. So just keep in mind, you can move this if you want to, but you're gonna need to purchase some longer hoses.
Also, this does not come with any fluid inside of it for shipping purposes, so you do need three quarts of a ATF Dexron III, that's not included, to get this to work. And of course, you're also gonna need a 12-volt battery power source to use it, to power it up. The foot plate is 10-by-10 inches. It can pivot back and forth. So if you're on uneven surface, it can pivot.
As you can see, I got a wedge in there so it doesn't flip over on me. And these mounting brackets on the back, they're already pre-welded onto the jack, I got 7 1/2-inches long and 4-inches tall overall. And then those will match up with these guys onto the trailer frame, and these are 2-inches long on the longer side, 1 3/8-inches on the shorter side. And these are also 4-inches long, obviously matching up that height. So again, you're gonna get those four with the hardware needed to install. Overall from the top of the jack to the ground, when it's fully retracted like it is now, I got 34 inches when I measured it beforehand, right to the top of the jack. When it's extended, that measurement goes to 55 inches. So again, folks, a nice heavy-duty jack. As you can see, it has a black powder coat finish, so it's very robust. It should protect it against rust, corrosion, those kind of things. And quite honestly, hydraulic jacks, if you've never used 'em, you're gonna wish you would've done it sooner. It's a great investment, especially if you're using that trailer for business or personal use, those kind of things, on the daily or even, you know, a couple times a week even. It's just so much easier not having to worry about cranking stuff up, go up and down quicker, those kind of things. Just takes a lot of stress off of you and honestly, less moving parts mechanically, and those kind of things. So a great option for you. As always, if you have any further questions about this or any other products, feel free to reach out to us here at etrailer. We're always happy to help you any way we can. I'm Steven, thanks for watching.
Customer Satisfaction Score:
84% were satisfied with this product
16% of customers were not satisfied
Ratings & Reviews

Christopher H.
8/25/2026
We appreciate you steering folks our way Brent and glad Andy got you taken care of. What type of trailer are you adding this jack too?

Mike L.
9/2/2026
I'm sorry that happened Mark, we'll ship those missing hoses out to you once we receive them from the manufacturer.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.






Mike L.
8/19/2026
I'm sorry that happened Jason, we're arranging to get those missing parts sent out to you!