Tis the Season for Holiday Savings
In-stock alternatives that are ready to ship
Use this anti-rattle device to keep your ball mount or hitch-mounted accessory from rattling and moving in your receiver. Quick, simple, bolt-on installation. Simply insert between receiver and accessory, then tighten down with included bolt.
Features:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
AJ: What's up everybody It's AJ with etrailer.com. Today we will be checking out this pro series anti-rattle device. Now what this does is it takes that shake and play out of your ball mount or cargo carrier, or even bike rack that it fits on. As you can see the ball mount goes up and down, back and forth. When you're driving on the road, you're going to hear that. We're going to install this and show you how it takes it out of it.
To attach our device, we're going to go ahead and pull the ball mount out. We're going to slide the device on, put it back in the hitch, find the hole just like you normally would. We're going to go ahead and put our pin in now.Then we're going to move the device up to the edge of the hitch. Work it in just a little bit. There you go.
You can see it sits, flush against the hitch, and then we'll just tighten the bolt back down. As you tighten it down, you're going to feel way more tension on it and that's taken away the shake and play from the ball mount. I tightened down the bolt, now we're going to tighten down the jam nut, just to give it that extra help. Looks like it's already pretty tight. Look at this, remember that shake and play, and that up and down, it's not happening anymore.
It's that easy to install, and it works that well. Like I said, it's not shaking, it's not moving like it was before at all. You can use this on your bike rack or your cargo carrier to take out that shake.Actually, we're going to show you that on a cargo carrier here in a little bit, but you have different options when it comes to these anti-rattle devices. Some of them only work with hollow shanks, and those would be the anti-rattle hitch pins that would go inside of the shank, and you put like a little block in there with the spring, and then you put the pin through that way. Those are great, but again, only work with hollow shank.
This isn't a hollow shank ball mount. This one goes along the outside, and it'll work with all those different types of ball mounts. So I think this one's actually better. I've used one also that has four or five bolts at the bottom. That one worked really well too, but it didn't have the jam nuts. The jam nut really makes it on this one so that the bolt can't get backed out and over time when you're towing or whatever, just in here.Taking a closer look at it, you can see it's a black powder coat finish and one solid piece of steel. So that's awesome, because you don't have a bunch of moving pieces or parts that you can lose. You really just have this bracket, this nut, and this bolt, and really when you go to take it off, you can just unscrew it here, and leave the bolt in there, and it's all going to stay in one piece. Plus, it's small enough to store pretty much anywhere you need it to.We've been sold the etrailor aluminum cargo carrier, just to show you how much shake and play the anti-rattle device is going to take out of it. Now I can move it with one hand, and show you all the movement it has, but that's aluminum, so it's not as heavy as a normal cargo carrier, so that's why it's moving so much. Let's go ahead and get it installed. We've installed this, check it out. You can see it's still moving just a little bit, but man, it's way less than it was before. So that just goes to show you whether you're using a cargo carrier, or a bike rack, or a ball mount, it's going to get the job done. That does it for our look at the pro series anti-rattle device..
Average Customer Rating: 3.9 out of 5 stars (56 Customer Reviews)
Use this anti-rattle device to keep your ball mount or hitch-mounted accessory from rattling and moving in your receiver. Quick, simple, bolt-on installation. Simply insert between receiver and accessory, then tighten down with included bolt.Ordered a curt 45794. The receiver hole lines up ok
(without) the anti rattle device BUT (with) the anti rattle device hole (1/4")
shy of lining up due to weld.
Karl
Wont fit! You have to have more access on your slide in hitch for this to work. When its on you cant get holes to line up to secure hitch. Sad as I was excited to try this out. Will be returning asap
Jenny N - 05/16/2022
Didn't stop the rattle. Useless.
The threaded hole that the bolt that tightens the collar to the hitch was heavily painted causing the bolt to mis-thread. Was never able to correct it even with a tap. Waste of money.
Sierra K - 10/18/2021Product works well. Bolt that was packaged won't thread in. Welded nut on the plate had damaged threads. It needs to be chased with a tap. Not a big deal.... unless you don't have one.
Just not heavy duty enough for my ease lift setup with lift bars on travel trailer. More suited for a light duty application like utility trailer without the bar setup.
Works great to stop rattle
I do not recommend this item. It is not constructed well enough to function as described. The bottom bent down slightly where the bolt is and loosened up. It might be ok for a small trailer with not much weight but it is of no use for anything else.
I had the unit for several months before trying to use it. I found it to be defective and completely unusable. Heavy overflow from the weld was inside the nut threads. The bolt could not be inserted. I tried cleaning the excess metal with a file but it was too extensive. Had to proceed without it. Do not buy.
The nuts that are welded on the inside were at an angle. I have a 2015 Toyota Tacoma this product would not fit because of hitting the Welded loops on the hitch for the safety chains. It would not allow my hitch to slide into the receiver far enough for the pin.
I used this the day after I received it. It's easy to install. It turned as trip with the trailer into a non-event with no beating and banging with the trailer. A relatively smooth ride and a lot more pleasant than previously. The only downside (its minor) is that the bolt and jam nut are different sizes (9/16" & 11/16"). It'd be nice to need only 1 wrench. Regardless, it was money well spent. If you have a noisy trailer or hitch, I'd get this anti-rattle clamp. Additionally, the welds were clean and smooth and the part looked powder coated. So, it should weather well over the years.
I'm very Happy!!!, with this Hitch Silencer. I've been to Northern Maine twice in the past year and New Hampshire hauling my SxS and this unit has held strong and silent. A must for anyone tired of hearing Hitch Rattle. Highly Recommend!!!
Fits perfectly, easy installation, and it's stops the rattling.
Had it a year now and it won’t stay tight. I’ve even torqued it beyond the limits and it still work’s it’s way loose after 1-3 road trips. The Mfg. should devise a way to lock down. Prevent this, and still be able to remove it when ready.
After thinkin it was heavy powder coat inside the thread holes because it was hard to screw in i kept On tightening the bolt.... Ended up having to retap the hole because i was sent the wrong bolt. However it does take away the play..
Plenty of options available online to fix the rattling problem from my trailer hitch accessories. Can't wait to try it and based on the design, it appears it should at least help limit noise/movement!
Haven't installed it yet, but upon screwing in the locking bolt, it stripped on a weld blob that had found its way into the threads of the welded nut. I ground off the weld blob and bought a new locking bolt at the hardware store. Hope this thing works...
Works great to stop rattles and I don't worry about someone easily stealing hitch.
Works great.
This thing really works. The bolt isn't quite long enough to allow the locking nut to be used however; another 3/8 would make the design perfect. If you would really like to refine this design, I suggest making the square hole smaller- just large enough to slide over the toung. The unit does work both ways- having the bolt positioned on top as well as on the bottom. I have it set up on top for ease of tightening the bolt. Hope this helps.
Works great. It holds the hitch securely and eliminates any wobble or rattle that there previously was. The best part is is that it is hardly noticeable when attached to the hitch.
Did not fit on a MB Metris 2016 factory installed trailer Hitch.
Hate to give it a poor rating because I was not able to put it to the test.
The product was great and the service and delivery are excellent. The only slight problem was in the video where they made the process of attaching the receiver sound easier than it was. My brother helped me and we have all the tools needed and are good at that kinda of stuff. But some of the procedures were difficult.
Just as it should , in perfect shape and works great.
I was sent the wrong product, returned it and received the right one in just days. No hassle and in a timely manner. I would do business with your company again. Thanks for the the great service!
Terry A - 11/17/2018
Do you have a question about this Hitch Anti-Rattle?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.