Most Popular 350 Lbs Vert Load for 2019 Ford Explorer

I use Curt Front Hitches from ETrailer with pintle hitch plates to make my own front protective bars and also rear protective bars in a rear truck, SUV. Or van hitch to protect my vehicles from bad drivers. Much stronger than bull bar or offroad front bumper bar protection

We live just south of Buffalo and Put this on our '11 Honda Ridgeline with a snowsport plow and a week later it snowed, and snowed and snowed... 5 feet in 24 hours and it's still snowing.... It's not good.... It's AWESOME! Not one driveway or even our street is clear... Except ours. It was easy to put together , easy to install and works exactly like it's advertised! It's November and it paid for itself already. Communication with etrailer was exceptional. We could not be happier with the whole setup.

Excellent instruction video! I would hope on future videos the dark black parts might be contrasted, they are taken from below and I am sure my lighting was lacking under an un-jacked jeep! The plastic rivets on vehicle are two part and in a restricted trough which were a pain to replace other than that issue everything was great!

Fits perfect and works just as I needed it to. I use it for my SnowSport plow set-up on a 2022 Gladiator Sport Max Tow. I’ve been using front receivers for this same plow for the last 24 years. It’s been used on 5 different trucks and this front receiver mount plow is the BEST. *** When installing on a Gladiator(possibly the Wrangler as well), the front plastic trim below the bumper needs to be cut for receiver clearance. I wanted a tight and “factory looking” install, so I took my time with a vibrating cutter and very sharp utility knife. After trying to put it back in place, the hole is not just square, it’s shaped more like. “T”. I suggest you make small adjustments/cuts as you go forward. It may take several times fitting and cutting to get it right and tight, but in the end it does look like it came that way from JEEP. On the Max Tow package, there is also a metal skid plate that does not get reinstalled. Unfortunately that piece is where the back of the plastic fascia mounts. I ended up securing it with some long heavy-duty zip-ties and it’s worked well for a year now. Just an FYI for those installing the same receiver on their same vehicle.

This worked well for what I needed it to do on my 1955 Willys Wagon 4x4. I installed on the frame with body off. I extended the frame approx 9” and welded the hitch to the front of the frame. The goal was to use it as a base to drop down a winch plate with the idea of the winch cable being accessible from the bottom of the stock bumper. The hitch fit the width of the Willys frame perfectly with just a little trimming so as to be away from the front suspension hanger over by slightly over an inch. I then bought a badlands universal winch plate from Harbor freight and trimmed and welled to the frame extension and hitch. Super sturdy, with the added bonus of dropping a future winch lower so as to improve air flow and cooling to the engine. Still have to drill holes and mount front stock bumper and check clearances but appears this will work as I get the vehicle back to together well see how it turns out.

We installed a front mount trailer hitch receiever on "grandpa's" truck for his Snowsport Utility Plow and it works GREAT! It's been a year and we expect it to last far past the life of the vehicle!

A good install! A bit of trimming for my application , but the bolt holes lined up perfectly. This front hitch was not specifically for a Lexus GX 460 but I decided to try it. There is a small area of lower bumper plastic that had to be trimmed. The hitch was pushing up against it before it was high enough to be in place. Upon trimming that area, it went in perfectly. If trimming the lower plastic is not for you, probably best to pass. However for my use, it works well. It is a stout piece, very strong. I added a pic with a red line to show where the trim needs to be.

Installed on my 2012 Lexus GX460. Perfect fit once I cut the center section of the lower plastic area for it to fit. Also had to trim the bottom splash guard and bend in the L brackets that hold it on. Took me about 2 hours. Very happy with the outcome. Now can mount snow blade for the driveway clearing…or any other hitch items.