Replacement Spindle and Hub for my Lippert 3500# Axle
Products Featured in This Question
Question:
I am building a trailer spare tire carrier. I plan on mounting a spindle and complete hub assembly on it. That way, I will have a complete hub and bearings available, if needed on the road. My aluminum trailer was made by HandH Trailers using a Lippert 3500# axle. Do you have a spindle and complete hub assembly that would work?
asked by: ROBERT S
Expert Reply:
The #84 Spindle for 3,500-lb Trailer Axles part # TRU84FR and the Trailer Idler Hub Assembly for 3,500-lb Axles part # AKIHUB-550-35-K for a 5 on 5" wheel bolt pattern or the Trailer Idler Hub Assembly for 3,500-lb Axles part # AKIHUB-545-35-K for a 5 on 4.5" bolt pattern will have you set up and ready to go.
Product Page this Question was Asked From
#84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter
- Trailer Spindles
- Standard Spindle
- 1-3/4 Inch Diameter
- Round
- For 3500 lb Axle
- TruRyde
more information >
Continue Researching
- Shop: #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter
- Search Results: lh78vr
- Shop: GE Profile Propane RV Rangetop - 3 Burners - 21" Wide - Stainless Steel
- Video: The Low-Down on the Dexter Trailer Axle Beam with E-Z Lube Spindles
- Search Results: tru66fr
- Search Results: lh39fr
- Shop: Lionshead Trailer Wheel Center Cap w/ Snap-In Plug - 4.88" to 4.9" Pilot - Stainless
- Shop: Trailer Hub Grease Cap with Rubber Plug, 2.72" - Drive-In for EZ Lube Axles - Qty 1
- Shop: Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Video: Lippert Controller 2.070 x 1.5: The Breakdown
- Search Results: lippert 4400 lb axle
- Search Results: timken l44649
- Video: All About the Timken Grease and Oil Seal
- Shop: Replacement Shoe and Lining Kit for Manual Adjusting 10" Electric Brake Assembly - 3,500 lbs
- Search Results: lippert trailer hubs and drums
- Search Results: lippert brakes
- Q&A: Troubleshooting Slide Out Switch To Controller Wiring Issues
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Q&A: How to Determine the Size of a Trailer Hub Assembly for Replacement
- Shop: Suspension Enhancement
- Video: Timken Bearing Kit Installation - Enclosed Trailer
- Video: A Closer Look at the Replacement Handle for Bladex and Valterra Waste Valves
- Q&A: Bearing Kit for Lippert 4,400 lb Trailer Axle
- Q&A: Option For Replacing A Dexter 4,400 Lb Axle
- Q&A: Option For Replacing a 4,400 lb Axle
- Q&A: Replacement Axle for a 4,400 lbs AL-KO Axle
- Q&A: Choosing the Correct Axle for my 7 x 16 Cargo Trailer.
- Video: Feature Breakdown: #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle
- Video: Detailed Breakdown of the etrailer Electric Trailer Brakes