view cartView Cart
Only 2 Hours 23 Minutes Remaining



What our customers are saying:

I found this product to be very well made. Shipping was very reasonable and fast. I am very satisfied for a good product at a very inexpensive price...Thank You

Len

Martville, NY

2014 Nissan Accessories:

change make

Select 2014 Nissan Model



Select Model for Your 2014 Nissan



Accessories



2014 Nissan Questions and Answers


  • Recommended Roof Cargo Box for 2014 Pathfinder w/ OEM Roof Crossbars
  • To determine which Thule roof mounted cargo boxes are compatible with your Pathfinder, and which would allow full operation of your rear hatch without interfering, you'd need to take a measurement on your roof. If the crossbars are moveable, move the front bar as far forward as possible. Then, measure from the center of the front bar rearward until you reach the seam between the hatch and the roof. Since the crossbars on the Pathfinder are shifted toward the rear of the vehicle roof,...
    view full answer...

  • Where does the Connector of the Tow Ready Harness part # 118525 Install on a 2014 Nissan Frontier
  • If the connector you found on your 2014 Nissan Frontier has a red and a green wire coming out of it it sounds like you haven't found the correct connector yet. The correct one can be a little hard to find but it won't have any wires coming out of the front of it. Check out the video I attached that shows the Tow Ready Harness part # 118525 being installed in a similar Frontier as yours.
    view full answer...

  • Trunk Mount Bike Rack, Trailer Hitch, and Hitch Bike Rack for 2014 Nissan Pathfinder with Spoiler
  • Since your 2014 Nissan Pathfinder has that rear spoiler I do not recommend using the Thule Raceway, # TH9001XT because it would put stress on that spoiler which it is not meant to support. There is only one trunk mount rack I recommend on a vehicle with a spoiler and that is the Hollywood Racks Over-the-Top rack # HRF2. This rack has an additional upper arm piece that moves the top straps up and over that spoiler so no weight is put on it (since the spoiler is not meant to support...
    view full answer...

  • Higher Capacity Hitch for 2014 Nissan Altima to Accommodate Bike Rack and 2 Bikes
  • The only hitches offered for the Altima are Class I with a 200 lb tongue weight capacity. Since using an adapter lowers the TW capacity to the point where you can't carry both bikes, your only alternative would be to use a Class I compatible bike rack to eliminate the need for the adapter. I've linked you to our selection of Class I compatible platform-style bike racks. The Kuat NV # N106 is an excellent rack that's compatible with a Class I receiver. The rack can fold for storage or...
    view full answer...

  • Bed Mat/Liner Recommendation for a 2014 Nissan Frontier 5 ft Bed Spray-in Bed Liner
  • I have a solution for you, but the BedRug Custom Truck Bed Mat # BMN05CCD that you referenced will not work with spray-in bed liners. Instead check out the BedRug Custom Full Truck Bed Liner # BRN05CCK, this will work with your spray-in bed liner and would do an excellent job as a bed mat/liner.
    view full answer...

  • How to Install Hopkins Custom Fit Vehicle Wiring # HM40975 in 2014 Nissan Pathfinder
  • The Hopkins Custom Fit Vehicle Socket # HM40975 that you referenced is a combination 4-pole/7-way vehicle-side socket for use in the 2014 Nissan Pathfinder that is equipped with the factory tow package. This part plugs in to the vehicle's wiring using its round U.S. Car Connector that would currently be installed at the back of the factory 7-way. I have linked you to a video showing this item being installed in a different vehicle; although the truck is different the process will be...
    view full answer...

  • Bike Rack Suitable for Use on 2014 Nissan Rogue With Class I Hitch
  • A light-duty Class I hitch is capable of supporting the weight of only 2 bikes (regardless of the rack's actual capacity). The linked article on hitch classes will explain in more detail. The Saris Thelma 3-Bike Rack # SA4239B that you referenced does have the same 1-1/4-inch size shank as Class I carriers but this is a Class II rack that will only fit properly in a Class II hitch. There is no 3-bike rack that can safely be used in a Class I hitch. The best option for carrying 3...
    view full answer...

  • Using a 2-Inch Hitch Bike Carrier on a 1-1/4-Inch Class I Hitch on 2014 Nissan Rogue
  • A light-duty Class I hitch such as the dealer-installed unit on your Rogue has a limitation of 2-bike capacity, regardless of the rack's actual capacity. A hitch adapter like the MaxxTow # MT70032 that you referenced will not allow you to safely use your 2-inch bike rack in your 1-1/4-inch hitch because all adapters like this have the unavoidable side-effect of cutting hitch capacity in HALF. So, your 200-lb-rated Class I hitch would have only a 100-lb tongue weight capacity if used with...
    view full answer...

  • Is the Curt Trailer Hitch # C11396 Compatible with the 2013 Leaf S Model
  • My contact at Curt tells me Curt hitch # C11396 is a fit for all models of the 2014 Nissan Leaf, including the S model. If you want to do some light duty towing you will want the following parts: The recommended ball mount for this hitch is # C45520. The recommended pin and clip is # F-4. The recommended 1-7/8" hitch ball is # C40001. The recommended 2" hitch ball is # C40018. As long as your trailer weight doesn't exceed the rated towing capacity of your Leaf, or the 1500-pounds...
    view full answer...

  • Towing Capability of 2014 Nissan Versa
  • The hitch itself has a towing capacity of 2000 lbs and a tongue weight capacity (maximum amount of downward force hitch can safely withstand) of 200 lbs. I looked up the towing capacity of the vehicle by consulting an online copy of the owners manual, and found on page 9-17, it states not to tow a trailer with the vehicle. I can't recommend anything that would contradict the vehicle manufacturer's recommendations. If you were planning on using the hitch as an attachment point for a bike...
    view full answer...

  • Installing Curt # 55571 Trailer Wiring Harness on 2014 Nissan Murano
  • I spoke with my contact at Curt, and apparently Nissan changed the fuse box for the 2014 model Murano. I was told that they are in the process of updating the instructions to reflect the change. It is necessary to change the existing 30 amp fuse in the 'T/Tow Lamp' position with the 10 amp fuse included with the trailer wiring harness.
    view full answer...

  • Wiring Harness Options For 2014 Nissan Xterra Without Factory Tow Package
  • I spoke with my contacts at our suppliers and asked about your 2014 Nissan Xterra. They were unable to confirm that the Tow Ready Harness, part # 118525, you mentioned is a fit for your vehicle. They have not done the test fit for a 2014 Xterra yet. My contact at Curt said they would be surprised if there was not a connector on your Xterra that the Curt T-Connector Vehicle Wiring Harness, part # C55441 would plug into. They told me that most folks have found this connector under the...
    view full answer...

  • Hitch Recommendation for 2014 Nissan Rogue for Use with Thule Doubletrack Bike Carrier # TH990XT
  • The Thule Doubletrack Platform-Style 2 Bike Carrier # TH990XT is an excellent choice in a platform-style hitch-mount rack. It combines sturdy build with a limited lifetime warranty and includes locks for both the rack itself and your loaded bikes. Since this is a substantial product (it weighs about 45-lbs without your bikes) I suggest you go for a high-capacity Class III hitch. The most popular such unit among owners of the Nissan Rogue is the Curt # C13168 which has a tongue weight...
    view full answer...

  • Troubleshooting Curt Fri-Flex Brake Controller Installation in 2014 Nissan Frontier
  • I suggest you disconnect your trailer and test both the tow vehicle and trailer independently. Please note that if your vehicle's 7-way trailer connector has LED test lights built into it, then the TriFlex brake controller will not be compatible. First you can check the signals going into and leaving the Tri-Flex. Apply a circuit tester like # 40376 to the black wire at the controller. This wire carries 12V power to the Tri-Flex and should be hot at all times, even when the vehicle is...
    view full answer...

  • Hitch Recommendation for a 2014 Nissan Rogue SV Select
  • Yes, the Draw-Tite Max-Frame Trailer Hitch # 75902 has been confirmed to fit the standard 2014 Nissan Rogue and the Rogue Select so it would work for you. For trailer wiring I would recommend the Curt Trailer Wiring Harness part # C56033. Check out the install video I attached. For ball mounts I recommend the etrailer Ball Mount Kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a carrying bag.
    view full answer...

  • Dimensions of Dallas Cowboys 2-Inch NFL Trailer Hitch Receiver Cover # HTCC2008
  • On part # HTCC2008 the distance from the rear surface of the emblem to the forward-facing edge of the hitch pin hole (the edge closest to the driver) is 3-1/8-inches. The distance from the rear surface of the emblem to the rear-facing edge of the hitch pin hole is 2-1/2-inches. These dimensions will vary slightly by manufacturer. The Dallas Cowboys 2-Inch NFL Trailer Hitch Receiver Cover # HTCC2008 from Great American Products is USA-made and features a die-cast zinc emblem mated to...
    view full answer...

  • How to Mount Hollywood Racks Over The Top Bike Rack # HRF2 on 2014 Nissan Rougue
  • There are a few different ways to make the upper connection of the # HRF2, as shown in the photo I've edited for you. If the seam where the hatch meets the roof is metal, the hooks can be used. If the hooks would need to attach to the plastic spoiler, the hatch anchors which would shut in the hatch would be used. The straps can also connect to the side rails or crossbars of a roof rack. This is shown in greater detail in the instructions I've linked to. The hatch should not be opened...
    view full answer...

  • Trailer Wiring Harness for 2014 Nissan Frontier
  • We offer two different trailer wiring harnesses for your 2014 Nissan Frontier, a custom-fit plug-in kit # 118525 and a universal hard-wire type kit # 119147KIT, both from TowReady. I have linked an installation video for each. Either of these will provide a 4-pole flat trailer connector to provide lighting functions to your trailer. You might consider adding a mounting bracket # 18144 to hold the connector at your rear bumper.
    view full answer...

  • Recommendation to Carry Bikes with a 2014 Nissan Altima that Does Not Require Heat Sheild Removal
  • Since installing a hitch would require you to void the warranty of your 2014 Nissan Altima, the best option I could recommend for you to carry bikes with your vehicle would be to use a trunk mounted bike rack. The best trunk rack we offer that is also confirmed to fit your vehicle would be the Thule Raceway 2 part # TH9001XT. The Raceway 2 includes a number of advanced features, including the patented Thule Fit-Dial system which makes precise installation simple and repeatable. This...
    view full answer...

  • Installing 7-Way Trailer Connector on 2014 Nissan Frontier
  • To install a 7-way, you'd first need to install the 4-pole flat connector (if you don't already have one.) I'd recommend the Tow Ready wiring harness, part # 118525. Once that's in place, how you would proceed will depend on the trailer you're pulling. If the trailer does NOT have brakes, but just the lighting circuits, you can simply use the # 37185 adapter. The adapter would plug into your existing 4-pole, and the white wire with the ring terminal on it would ground to the vehicle...
    view full answer...

  • Does a Wire Need to Be Run to the Battery to Install Tow Ready Wiring Harness 118481
  • Yes, you will need to run the power wire from the Tow Ready Wiring Harness part # 118481 to your battery. The connections to your tail light wiring harness are very much plug and play as they will just connect in line with your tail light connectors. The reason you need to run the power wire to the battery is because the # 118481 uses your tail light circuits as signal wires and actually powers the tail lights of your trailer with the power it draws from the battery of your 2014 Nissan...
    view full answer...

  • Towing Small Heavy Trailer with a Nissan Leaf and Class I Hitch
  • A weight distribution system is recommended anytime you tow a trailer that weighs more than 50 percent of the tow vehicle, but it will not allow you to take on more weight than the maximum capacity. They are also incompatible with 1-1/4 inch hitches. Curt Trailer Hitch Receiver # C11396 is the only hitch we sell for your vehicle and is rated at 1500 pounds gross trailer weight and 150 pounds tongue weight. The combined weight of the trailer and contents cannot exceed 1500 pounds. You...
    view full answer...

  • Roof Rack And Cargo Carrier Recommendation For 2014 Nissan Altima 4-Door
  • The Yakima Q Tower Roof Rack System Is a good fit for your 2014 Nissan Altima 4 door. The weight capacity for the roof rack is 100 lbs. That would include the weight of any cargo box you choose added to the weight of any cargo you place in the carrier. The front crossbar is placed 15-1/8 inches from the windshield. The crossbar spread is 24 inches. Due to the roof weight capacity on your Altima, my recommendation would be to use a cargo bag instead of a cargo box. The smallest Skybox...
    view full answer...

  • How Easy is it To Crank the Jack Handle on Trailer Hitch Mounted Scooter / Wheel Chair Carrier
  • I spoke with my contact at Oldenkamp to get more information on the ease of using the jack part of Trailer Hitch Mounted Scooter / Wheel Chair Carrier, # RHWC1114. It takes 6 turns of the handle to move the carrier up or down one inch. So this means it will require a lot of turns but the turns will be pretty easy. I noticed that you have a 2014 Nissan Versa Note. The trailer hitches available for the vehicle are all Class I trailer hitches and the Oldenkamp carrier would not fit because...
    view full answer...

  • Cargo Basket for a 2014 Nissan Rogue with Factory Side Rails
  • Nearly all cargo baskets require crossbars to mount. Surco does make a basket, called the Safari basket, but they only fit up to the 2012 Nissan Rogue and not up to 2014. In order to mount a basket you are going to have to have crossbars. The most economical option that fits your 2014 Rogue is a Yakima system using the RailGrabs, # Y00138 and crossbars # Y00408. With this system installed the recommended bar spread (center to center distance between the bars) is 38 inches. Or you...
    view full answer...

  • Trailer Hitch for a 2014 Nissan Murano Cross Cabriolet
  • Actually Curt trailer hitch # 13577 is the only hitch we carry that does fit the 2014 Nissan Murano CrossCabriolet model. To complete your towing set up I recommend etrailer ball mount kit # 989900. It includes 2 ball mounts, 2 balls, a hitch pin with clip, and a storage bag. You will need to visit a Nissan dealer for trailer wiring.
    view full answer...

  • Will Hidden Hitch 2-Inch Class III Hitch # HH87663 Fit 2013 Nissan Rogue Carryover
  • For your Nissan Rogue, a 2013 model carried over into 2014, Hidden Hitch 2-Inch Class III Hitch # HH87663 is a correct fit. This hitch will bolt on using included hardware and requires no drilling or welding. The written installation instructions are linked. If you will be towing and need a wiring harness you can use part # 118480 from Tow Ready, which is a custom-fit harness that does not require you to cut into the wiring in your Rogue. It installs by simply plugging in at the vehicle...
    view full answer...

  • Which Trailer Hitch Sticks Out the Furthest on a 2014 Nissan Rogue
  • You are correct, the Hidden Hitch trailer hitch # HH87663 and Draw-Tite trailer hitch # 75902 do stick out further than the Curt trailer hitches for your 2014 Nissan Rogue. On both hitches, they stick out 2-1/4 inches further. Both hitches do have the same dimensions. And on the Yakima DoubleDown Ace 5, # Y02452, it measures 9 inches from the center of the hitch pin hole to the back of the upright mast. What you can do is measure from the furthest back hitch attachment point on the...
    view full answer...

  • Will Hitch Extender 45791 and Anti-Rattle Lock 63232 Fit w/Curt Trailer Hitch for 2014 Nissan Rogue
  • Yes, the Curt hitch extender # C45791 and anti-rattle device # 63232 are compatible with each other and with Curt trailer hitch # C13168. Please keep in mind that the use of the extender will reduce the tongue weight capacity of the trailer hitch by 50 percent. That will reduce the hitch you have on your 2014 Nissan Rouge to 175 pounds.
    view full answer...

  • Curt Trailer Hitch Receiver Recessed Too Far Under 2014 Nissan Rogue to Use Thule T2 Bike Rack
  • The issue is that if hitch manufactures extended the receiver more then you would have the same problem as you would when using a hitch extender. It would put too much stress on the hitch and could cause damage to the hitch or vehicle. Draw-Tite hitch # 75902 extends out a little further. Approximately 2-1/4 inches further than on the Curt hitch. And on the Curt hitch the hitch pin hole to rear bumper measurement is 8-1/4 inches. On the Draw-Tite hitch that measurement would be approximately...
    view full answer...




Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email





Only 2 Hours 23 Minutes Remaining

etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com