Ford Freestyle owners are most interested in these products

change vehicle

Ford Freestyle Trailer Hitch

Ford Freestyle Trailer Wiring

Ford Freestyle Bike Rack

Ford Freestyle Roof Rack

Ball Mounts

Ford Freestyle Cargo Carriers

Ford Freestyle Brake Controller

Ford Freestyle Performance Chip

Ford Freestyle Tire Chains

Ford Freestyle Windshield Wiper Blades

Ford Freestyle Floor Mats

Ford Freestyle Videos

Trailer Hitch Installation - 2006 Ford Freestyle

Today on this 2006 Ford Freestyle we are going to install part number 87108 from Hidden Hitch. This also applies for part number 75299 from Draw-Tite. Our first step is to go ahead and lower the carbon canister. There are four bolts that hold this in place. One here, one back here that is hidden, and two on the bottom right here. Lets go ahead and lower it, it will stay on its own. Be careful with it. Now I have plenty of room to work on the frame rail right here.

Ford Freestyle Questions and Answers

• Can Curt Trailer Hitch 13542 Support a 279 Pound Scooter Carrier and Scooter on 2006 Ford Freestyle
  
• The Curt trailer hitch # 13542 has a tongue weight capacity of 350 pounds so the hitch can handle the 279 pound total weight of the scooter and carrier. However you will need to check the owners manual for your 2006 Ford Freestyle to determine what the tongue weight capacity is for the vehicle. I have included a link to the installation instructions for you to view.
  view full answer...


• Origin for Curt Trailer Hitch # 13542 for a 2006 Ford Freestyle
  
• The Curt trailer hitch # 13542 for the 2006 Ford Freestyle is made in the US. I have included a link to the installation instructions for you. If you plan on doing some towing, I recommend the etrailer ball mount kit # EBMK4. It comes with a ball mount, interchangeable ball set, hitch pin with clip and a carrying bag. For trailer wiring use # 118395. I have included some instruction and video links for the wiring as well.
  view full answer...


• How to Pick Out the Correct Rise/Drop Ball Mount for a 2005 Ford Freestyle
  
• I do not have the exact figure for how many inches of rise or drop you would need to order a drawbar with. But I can help you figure this out. The hitch opening for the Draw-Tite hitch # 75299 will basically sit right under the bumper of your 2005 Ford Freestyle once installed. So if you measure from the ground to bottom of the bumper you will have basically the distance rise/drop you would have if you had a ball mount with no rise or drop. So if the distance happens to be 16 inches from the
  view full answer...


• Trailer Hitch Mount Bike Rack Recommendation for a 2005 Ford Freestyle that Allows the Hatch to Open
  
• You could remove the pin that secures the central arm of the Swagman Quad, # S64690, and let it tilt down. however, you could not do it with the bikes attached to the rack because it was not designed for that purpose and could damage the rack. Also, if the bikes are not loaded you could just fold down the closest upright arm and open the hatch. What I recommend instead is to go with a swinging bike rack like the Thule Vertex, # TH9031. This rack also holds 4 bikes but has the ability to swing
  view full answer...


• Curt Class III Trailer Hitch Compatibility With a 2007 Ford Freestyle
  
• The Curt Class III Trailer Hitch, # 13542, will fit on your 2007 Ford Freestyle. You may be interested in a few other items if you plan on doing any towing with this hitch. I would recommend you also get the T-One Wiring Harness, # 118395, and the Ball Mount Kit, # EBMK4. This kit comes with a ball mount, 1-7/8 inch and a 2 inch hitch ball and a pin and clip. The wiring harness will plug directly into the tail light assembly on your vehicle. I have included a link to the installation instruc
  view full answer...


• Adding Crossbars to a 2007 Ford Freestyle to Mount SportRack Explorer Cargo Box # A90095
  
• Yes, you can add crossbars to the existing side rails on your 2007 Ford Freestyle. You will need Thule Crossroad Roof Mounted Roof Railing Foot Pack, # TH450, which will attach to the rails. Then, you can install Thule Load Bars, # THLB50. With this system installed, you will be able to mount the SportRack Explorer Cargo Box, # A90095, to the roof. I have included a link to the installation details and a video review of the cargo box.
  view full answer...


• Are Dexter Hubs and Axle Components Compatible with AL-KO Axles
  
• Many axle parts like hubs and brake assemblies are interchangeable. When replacing the hubs or drums, you need to make sure you get the proper hub for the spindle on the axle. Each manufacturer uses a range of spindles depending on the application, but they are all standardized sizes. The way to determine what hub you need is to remove the old hub, and find the bearing numbers that are stamped or etched into the bearings. This will tell you what spindle you have as well as what hub you will n
  view full answer...


• Installing 7-Way Trailer Connector on 2005 Ford Freestyle
  
• To wire the 7-way connector you have already purchased, you will need the Pigtail Wiring Harness for Pollak Replacement 7-Pole RV Socket, part # PK11998. This harness would plug into the rear of the trailer connector, and the bare leads on the other end would connect to the existing vehicle wiring, using the color code mentioned in the product description. If you do not already have one, I would recommend using a circuit tester, like part # 40376 to locate the correct circuits for installing the
  view full answer...


• Will the Thule Parkway Hitch Mount 4 Bike Rack Fit on a 2006 Ford Freestyle
  
• The Thule Parkway 4, # TH956, will fit on your 2006 Ford Freestyle if you have a 2 inch receiver opening on your trailer hitch. Also, you will need to measure from the center of the hitch pin hole to the furthest part of the rear of the vehicle. If this measurement is less than 9-1/2 inches, the rack will fit. I have included a link to the installation details below.
  view full answer...


• Hitch Recommendation for Bike Rack on 2006 Ford Freestyle
  
• I would recommend that you get a Class 3 hitch with a 2 inch receiver for your vehicle. The Class 3 hitch will provide the most versatility and options for towing and hauling. You will have a wider selection of all accessories, bike racks included, with the 2 inch receiver hitch. It will also give you the best options if your towing or hauling needs should change in the future. The Draw-Tite Class 3 Trailer Hitch, item # 75299 would be an excellent choice and installs easily with no drilling
  view full answer...


• Installation Instructions for Tow Ready 4-pole to 7-pole Wiring Adapter Part # 30717
  
• The manufacturer does not make instructions available. It is possible that since the customer review you read was from Canada that he/she received instructions. I can walk you through the wiring process though. First, find a place to securely install the 7-pole connector somewhere at the rear of your vehicle. Using a mounting bracket for 7-pole connectors such as part # 18138, can provide you with a clean and secure mounting point. Next, plug in the the 4-pole connector on your vehicle into t
  view full answer...


• Wiring a French Built Mecano Galva Utility Trailer to a 2007 Ford Freestyle
  
• European trailer wiring is very different from North American, specifically U.S. trailer wiring. In Europe a 7-Way connector is used to achieve the same functions U.S. trailers use in a 4-Way system. Our brake and turn signal functions are combined. A U.S. 4-Way is set up as follows: Brown - tail lights, yellow - left turn and brake, green - right turn and brake, and white is ground. Reverse lights are not typically used on small utility trailers in the U.S. In many states they are not re
  view full answer...