Chevrolet Camaro owners are most interested in these products
change vehicle
Trailer Hitch Installation - 1995 Chevrolet Camaro - Draw-Ttite
Today on our 1995 Chevrolet Camaro well be selling jaw type hitch part number 24586 before and install here are few measurements from the top of the receiver tube to the ground is 12 and a half inches and from the center of the hitch pin hole to the outer most part of the bumper is 9 and three quarters inches this will help you in selecting accessories suchas a cargo carrier or a bike rack now well go ahead with our install with our vehicle raise up in the air. Well go ahead and start by removing the exhaust bracket here and because ofour vehicle has custom exhaust this might be the same as your vehicle. With our exhaust remove well go ahead and point out the locations to our pitch mounting on the driver side here we used the two rear most holes on the patch of your side will be the same the third mounting point will be a whole that well have to drill once the hitches is in place. Well also be using the access hole on the inside of the frame on either side of the vehicle. Now using on our access hole here on the frame well need to install the two rear most fastener well simply take a fish wire slide it up through the mounting location in our access whole or we can slide our quarter block on and screw our carriage bolt too. well fit the spacer washer through the access whole with our carriage bolt.
Trailer Wiring Harness Installation - 1995 Chevrolet Camaro
Today on our 1995 Chevrolet Camaro well be installing trailer harness part number 18252. And for opening the rear deck lid, well remove the driver side inside trim panel. With the trim panel removed, we can peel the carpeting away at the back of the trunk which will expose our wiring. Now on this particular vehicle, they make it really nice. Youll notice here that the factory wiring harness is the same colors as trailer 4-pole wiring. Well also need to locate a ground for our 4-pole harness which, in the Camaro, we can use one of the existing ground points here directly underneath the latch.
Thule T2 Platform Style Hitch Bike Rack Review - 2012 Chevrolet Camaro
All right, today on this 2012 Chevrolet Camaro, we're going to do a test fit of part number TH917XTR from Thule. This is the T2 Platform Style Bike Rack. A couple of quick notes about this bicycle rack, that it will work with class 1 and class 2 receiver hitches. This bike rack will tilt up forward for storage and also it will tilt down away to provide easier access to the back of the car. Okay, we're going to start off a test fit by installing the bike rack into the hitch then we'll install the anti-rattle bolt and tighten it down. Now, due of the nature of the hitch, it can only be designed to fit the car that sits pretty far back in there so it's going to be a tight fit to begin with.
Thule Apex 4 Hitch Bike Rack Review - 2012 Chevrolet Camaro
All right today on this 2012 Chevrolet Camaro we are going to do a test of part number TH9025 from Thule, this is Apex-4 bike carrier. A couple of quick notes about this bicycle rack that will work with 1-1/4 inch receiver hitches both class I and class II. However with a class I receiver hitch you are only limited to carrying two bikes. This will also work with a 2-inch receiver hitch which the included spacer. We'll go ahead and start our test fit by installing the bike rack into the hitch we'll make sure that the integrated hitch pin snaps into it then we'll go ahead and tighten it down with the anti-rattle device. All right with the bike rack installed we'll go ahead and give you some measurements that will give you an idea of clearing between the bicycle rack and the car and the ground.
Rhode Gear Highway Hitch Bike Rack Review - 2012 Chevrolet Camaro
All right, today on our 2012 Chevrolet Camaro we're going to do a test fit of part number RG8015220 from Rhode Gear. This is our Highway 2 bike carrier. A couple quick notes about this bike rack is that it will work with 1-1/4" receiver hitches both class I and class II. It will also work with class III receiver hitches with the included spacer. We'll go ahead and start off our test fit by installing the bike rack into the hitch then we'll install the anti-rattle bolt and put the safety pin on the other side. All right, with the bike rack installed we'll go ahead and give you some measurement that will give you an idea of clearance between the bike rack and the car and the ground.
SportRack EZ Hitch Bike Rack Review - 2012 Chevrolet Camaro
All right, today on 2012 Chevrolet Camaro we're going to do a test fit of part number A30901 from Sportrack. This is a Sportrack EZ 2 bike rack. Couple of quick notes about this bicycle rack that will work with 1-1/4" receiver hitches both class I and class II. It will also work with class three receiver hitches with provided spacer. Okay, we'll go ahead and start off our test fit by installing the bike rack into the hitch then tighten it down in anti-rattle bolt then installing the safety pin on the other side. Okay, with our bike rack installed we're going to go ahead and give you some measurements that give you an idea of clearance between the bicycle rack and the car and the ground clearance.
Thule Vertex 4 Hitch Bike Rack Review - 2012 Chevrolet Camaro
Alright today on this 2012 Chevrolet Camaro, were going to do a test fit for part number TH9029 from Thule. This is a Vertex 4 Bike Carrier. A Couple of quick notes about this bike rack is that this will work with 1-1/4-inch receiver hitches both class 1 and class 2. However, with a class 1 receiver hitch, youre only limited to carrying two bikes. This will also work in 2-inch receiver hitch with the included spacer. On this car, well be using a class 1 receiver hitch.
Trailer Hitch Installation - 2012 Chevrolet Camaro
Today on this 2012 Chevrolet Camaro, were going to install a hitch from Draw-Tite, part number 24850. This will also apply to part number 60266 from Hidden Hitch. Ok, now this is what the hitch looks like when its installed on the car. Next, well give you some measurement to help you out in selecting some accessories such as a bike carrier or a cargo carrier. From the top of the receiver opening down to the ground is going to be 10 inches and from the center of the hitch pinhole to the outside edge of the bumper is going to be 12 inches. Now, we'll go ahead and show you how the hitch is installed.
Chevrolet Camaro Questions and Answers
- Back up Light Wire Color for 2010 Chevrolet Camaro To Install Peak Back-Up Camera Part # PKC0RB
- To determine which wire is designated for the back-up light on your 2010 Chevrolet Camaro to install your Peak Back-Up Camera, you will need to do some testing. For this I recommend having a circuit tester handy, like part # 3808.
Using the circuit tester method is the most accurate. First, locate the wires for the reverse lights. On the latest generation of the Camaro, the reverse lights are on the bumper, near the license plate. You may be able to locate this wiring through the trunk, or ev
view full answer...
- Which MagnaFlow Exhaust for Deeper Exhaust Note on 2013 Chevrolet Camaro 2LT With 3.6L V6
- The MagnaFlow Stainless Steel Straight-Through Universal Muffler for V6 Camaro, part # MF14277, is a weld-on dual outlet muffler designed specifically for the V6 Camaro with a single transverse muffler.
My contact at MagnaFlow indicates that the muffler for your Camaro is part # MF14226. This is a single-inlet, single-outlet muffler made of 100 percent stainless steel and offering unrestricted flow for increased horsepower, torque and fuel efficiency, along with a deeper exhaust tone. This mu
view full answer...
- Curt Hitch Recommendation for a 2001 Chevy Camaro
- The Curt Trailer Hitch # 11117 that you referenced should work well on your 2001 Chevy Camaro. Having dual exhaust will not cause a problem is this hitch is confirmed to fit other F-bodies like yours that come standard with dual exhaust.
You will need to be sure you do not exceed the towing capacities of your vehicle and this hitch with your trailer. Your owners manual will have the towing capacities listed for your vehicle.
When determining the overall towing capacity of a setup you must
view full answer...
- Catalytic Converter Recommendation for a 1994 Chevrolet Camaro V6 3.4 Liter
- The catalytic converter that I would recommend for your 1994 Chevrolet Camaro V6 3.4 Liter is the MagnaFlow Stainless Steel Direct-Fit Catalytic Converter, # MF23494. This converter was specifically designed to fit your vehicle for an easy bolt-on installation and eliminating the need for welding or drilling during the installation.
This converter will use the factory hanger locations and flanges and is EPA approved for Canada and all states except California.
Just in case you were inter
view full answer...
- Is the Oldenkamp Hitch Mounted Motorcycle Carrier Safe for Towing a Motorcycle in Neutral
- The Oldenkamp Hitch Mounted Motorcycle Caddy, # RHMC1, is designed to tow motorcycles up to 750cc. If your motorcycle is chain driven, then you should remove the chain. Removing the chain will allow your back wheel to rotate freely, similar to the front wheel, without rotating the motor.
If your motorcycle is shaft driven, then you will not have a problem as long as you put your motorcycle in neutral and do not exceed 65 miles per hour when towing.
You should also check with the manufact
view full answer...
- Replacement 2-1/2 Inch Catalytic Converters for a 1988 Chevrolet Camaro Iroc-Z
- I checked with my contact at MagnaFlow for catalytic converter options for your 1988 Camaro Iroc-Z. He stated that due to the EPA and CARB regulations in California we cannot recommend that you install a catalytic converter that is different from the 2.25 converter that comes on your vehicle.
Modifying your exhaust system would not comply with the laws in California, which is why the shops are trying to sell you the 2.25 converter. They cannot sell a product for a vehicle that does not comply
view full answer...
- Trailer Hitch and Bike Rack Recommendations for a 2012 Chevy Camaro
- I do have a solution for carrying bikes with your 2012 Chevy Camaro but no trunk mount bike racks will fit because they cannot be safely mounted. You will need to install a trailer hitch, like # 24850, and use a hitch mounted rack.
For a rack, it must be compatible with a Class I trailer hitch and with a Class I you are limited to carrying a maximum of 2 bikes. I recommend the Swagman Titan, # S63400. This rack will fit a Class I, it features anti-sway cradles, it can tilt away from the vehi
view full answer...
- Bike Rack Recommendations for a 2011 Chevrolet Camaro Coupe
- At this time there are no trunk mounted bike racks that are compatible with your 2011 Chevrolet Camaro because they will not safely mount on your vehicle.
Instead, I would recommend installing a hitch like our Hidden Hitch Trailer Hitch, # 60266, and a hitch mounted bike rack like the Rhode Gear Highway 2 Bike Rack, # RG8015220. You may also want the Yakima Tube Top Adapter Bar, # Y02531, for bikes with slanted or alternative bike frames. A hitch and hitch mounted bike rack will help protect
view full answer...
- Curt Trailer Hitch Recommendation for a 1997 Chevy Camaro
- Yes, the Curt Trailer Hitch Receiver with Drawbar # 11117 should work well on your 1997 Chevy Camaro with factory dual exhaust. The only model Camaros it will not fit are the RS models.
I attached the installation instructions for this hitch for you to check out also.
If you plan on using the hitch for a bike rack or a cargo carrier Curt recommends you get a Curt Trailer Hitch Support Strap # 18050 to help provide extra support for the hitch.
To complete your towing setup you may be int
view full answer...
- What Ball Mount is Needed for a 2011 Chevy Camaro For Hidden Hitch Trailer Hitch 60266
- The Hidden Hitch trailer hitch, # 60266, actually comes with the correct ball mount, hitch pin and clip. On a Class I hitch, like this one, or Class II hitch, you must use the ball mount recommended by the hitch manufacturer or it will void the hitch warranty.
The ball mount measures 10 inches from the hitch pin hole to the ball hole but it is sufficient to clear the rear bumper because of the angle that the rear fascia is at. It is12 inches higher on the vehicle but not down where the ball
view full answer...
- Trailer Hitch Recommendation for a 2012 Camaro SS Transformers Edition
- I spoke with my contacts at Draw-Tite, Hidden hitch, and Curt. They all indicated that the available hitches for the 2012 Chevy Camaro should fit the Transformers edition as long as it does not have a dealer-added ground effects package.
On any of the hitches, only the receiver will be visible beneath the car. The cross tubing and mounting brackets will not be visible. I have included a link to the installation instructions for the Hidden Hitch that you have referenced.
Installation is not
view full answer...
- Transmission Pan Gasket for a 1984 Chevrolet Camaro Z28 IROC
- If your transmission pans bolt flange is still good and flat and you have all of the gasket material removed from the pan and transmission mounting area, the Replacement Gasket for GM Turbo 350, # D96900, will work on your 1984 Chevrolet Camaro Z28 IROC.
I have done a bit of transmission repair and replacement in the past and have found that if a pan is leaking after a new gasket is properly installed that the pan is usually the culprit. If you determine that a new pan is needed you could use
view full answer...
- Engine Oil Cooler Mounting Location Options for a 1994 Chevy Camaro
- I own a 1998 Pontiac Trans Am and have a very large transmission cooler plus an underhood ram-air kit (Fast Toys Ram Air) that blocks about 50% of the direct air flow that would go through the radiator and I have had no cooling problems. The cooling fans on our F-body cars are very powerful for cooling the radiator fluid and you should not have a problem with airflow through the radiator.
Also, our bottom breather style radiators are very efficient. You will notice that most modern cars have
view full answer...
- Header Connections Needed to Install a MagnaFlow Exhaust System on a 1968 Chevrolet Camaro
- As you have most likely realized, there will be some welding involved for the installation of the MagnaFlow Exhaust System, # MF15895, on your 1968 Chevrolet Camaro. You will need to find a flange that is compatible with your headers and have it welded to the front pipes that are included in the install kit, after they have been cut to the proper length.
If your headers do not have a flange and you need to create one, you could use a ball flange. We have 3 sizes of stainless steel ball flange
view full answer...
- Will Draw-Tite Trailer Hitch 24850 Fit a 2012 Camaro SS with Manual Transmission
- The instructions for the Draw-Tite Trailer Hitch, # 24850, do state that the hitch will fit all models of the 2012 Chevy Camaro with the exception of a convertible model or any model that has the dealer installed ground effects package. I have included a link to the installation instructions for you.
If you plan on doing some towing, the correct ball mount is # 3594 for use in the rise position only. For a ball, you can use # 19256 for a 1-7/8 inch diameter, or # 19258 for a 2 inch diameter.
view full answer...
- Will the Edge Insight Tune the Engine and Add Horsepower to a 2012 Chevy Camaro with 3.6 Liter V6
- The Edge Insight, # EP83830, does not tune the engine on a 2012 Chevy Camaro. Instead, what it does is allow you to view various parameters of engine performance. The data parameters you can monitor include:
Battery Voltage
Intake Air Temperature (IAT)
Engine Oil Pressure (EOP)
Engine Coolant Temperature (ECT)
Engine Oil Temperature (EOT)
Transmission Fluid Temperature (TFT)
Miles Per Hour (MPH)
Miles Per Gallon (MPG)
Revolutions Per Minute (RPM)
1/4-mile and 0 - 60 times
It will
view full answer...
- Recommended Car Cover for 2012 Camaro
- The primary difference between the two covers you mention is the ding resistance offered. The Poly Cotton model, item # C16873TS, is a very soft cover, but would be best in an environment where nothing would bump into or fall against the vehicle. The Flannel Custom Fit Cover, item # C16873TF, would offer more ding resistance due to the napped underside.
In other words, if the vehicle will be stored in your garage with a constant stream of children passing through, go for the thicker cover and
view full answer...
- Draw Tite Hitch Cargo Carrier Recommendation for a 2010 Chevy Camaro
- Considering how low to the ground the hitch opening is on your 2010 Chevy Camaro I would recommend the Draw-Tite Hitch Cargo Carrier # 6500 as it has an angled shank that raises the platform an additional 3 inches above the hitch opening.
I attached installation instructions for you to check out for this product also.
You may also be interested in purchasing a Trailer Hitch Lock # 7682. I attached a review video for this product for you to check out also.
view full answer...
- Is it Easier and Cheaper to Upgrade or Replace a Weight Distribution System
- Unless your Reese weight distribution system was made in the last 3 and a half to 4 years, the new style bars will not fit in the old style head. You would need to also replace the head. After you replace the head and the bars, the cost is about the same as a new system, which is what I recommend. With a new system you will get all new parts instead of having to rely on some new parts and some old parts.
The new head for trunnion bars is # RP58167. For 1,200 pound bars compatible with a Reese
view full answer...
- Availability of Roof Rack For Bike and Kayak On a 2010 Chevrolet Camaro
- The Yakima Roof Rack Kit, part # Y00678, part # Y00409, part # Y00124, is the only roof rack we have available for the 2010 Chevrolet Camaro.
The Yakima Boa bike rack # Y02065 is the only Yakima bike rack that does not work on the Camaro. All of the other Yakima bike racks will work on your roof. I am including a link to a product page that will list the Yakima bike racks for your Camaro.
I spoke with my contact at Yakima and he said they do not recommend any Kayak carrier for the 2010 Ca
view full answer...
- Quality and Installation of the Putco Liquid Grille Insert # P91160 on a 2010 Chevrolet Camaro
- The grille on the Putco Liquid Grille Insert, part # P91160, is made of a heavy-gauge, aluminum and installs to your existing factory grille on your 2010 Chevrolet Camaro. It comes with a lifetime warranty. The grille insert contains two pieces, an upper grille insert and the lower insert.
I do not have any pictures of the grille by itself, but I spoke with my contact at Putco and she said that it will clamp-on to your factory grille using the included bolts and mounting brackets.
view full answer...
- Why Does Trailer Wiring for a 2011 Chevy Camaro LT1 RS Require a Direct Connection to the Battery
- The Draw-Tite Custom Fit Vehicle Wiring, # 118486, for the 2011 Chevy Camaro includes a separate power wire that connects to the vehicle battery as a means to protect the vehicles sensitive wiring from an overload situation. The wiring on modern cars is more efficient but is not always made to handle the extra power draw associated with powering trailer lights.
The powered converter virtually eliminates power draw from the tail light wiring, protecting the vehicles sensitive wiring. Without i
view full answer...
- Position of the Fans in Derale Dual High-Output Electric Radiator Fan-and-Shroud Assembly # D16927
- I spoke with my contact at Derale and he stated that on the Dual High-Output, Electric Radiator Fan-and-Shroud Assembly, # D16927, the fan on the driver side would be in the upper position making the fan on the passenger side in the lower position.
This fan is a puller, meaning that it mounts between the radiator and the engine and pulls air through the radiator. You will need to make sure that you have enough clearance to install the fan. It is 3-3/4 inches wide, 18 inches tall, and 26 inch
view full answer...
- Is Drilling Required to Install a Trailer Hitch on a 1998 Chevy Camaro Z28
- To install Draw-Tite Trailer Hitch, # 24586, on a 1998 Chevy Camaro Z28, there is some drilling required. Take a look at the installation instructions for the trailer hitch linked below. Steps 4 and 5 explain where the holes will need to be drilled. Please note that this hitch along with # 60889 will not fit on models that have dual exhaust pipes on the drivers side.
The recommended ball mount for towing is # 3592 for use with ball # 19256 (1-7/8 inch diameter) or # 19258 (2 inch diameter). F
view full answer...
- Thule Goal Post Load Bar and Cross Bars for 2007 Explorer Sport Trac with Factory Roof Rails
- The Thule Goal Post includes a 58 inch load bar. This entire width is usable, but if the included load stops are used, the end caps on the load bars will decrease the overall width by approximately 1-1/2 inches per side.
You did not mention how may cross bars you were wanting to use on top of your Sport Trac. We offer a Thule Crossroad System, part # TH45050 that includes two 50 inch long cross bars, and the four locking feet that strap the bars to your existing roof rack.
If you are only
view full answer...
- What is the Inlet and Outlet Diameter of MagnaFlow Spun Stainless Catalytic Converter Part MF54956
- The inlet and outlet diameter is 2-1/2 inches. This Catalytic Converter is 49-state approved. It is not approved in California.
view full answer...
- Ability of Rackem Double Barrel Trailer Tailgate Assist Part # RA-27C to Withstand Poor Weather
- The Rack-em Tailgate Assist, part # RA-27C is specifically designed to be mounted in an exposed location. You should have no weather related problems with it.
view full answer...
all Chevrolet Camaro questions
