To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring - no cutting, splicing or tapping required. Converter is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side interior trim panels in your rear cargo area.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Much easier than cutting and splicing
Excellent fit. Installed easily.
Easily installed, great directions.
Easy install just follow the instructions, worked first time.
Product was as advertised. Grade of wiring is minimal but functional.
I Have never installed anything as easy as this. WELL WORTH THE PRICE!
Best wiring job I've ever done took 10 minutes unbelievable.
product came in when expected and the items requested
Completely satisfied. Quick free shipping and great products. Everything as promised.
This installed very easy. Only took 10 minutes with very little effort.
My son installed the trailer wiring on the 2007 Corolla without any problems.
Followed the instructions and installed it in just a few minutes.All wires are out of the way till you need them
EASY TO PLUG IN AS SOON AS I FIGURED HOW TO GET PLUG APART. HARD TO SEE IN TRUNK. I SHOULD HAVE STARTED ON RIGHT SIDE TAIL LITE FIRST
Fantastic service and products. Super reliable and totally professional. I am a repeat customer and will continue to be.
Great serviceThanks for the great service. I received my harness just in time for the week end.
Thanks again.
John Dow
I HAVE PURCHASED FROM E-TRAILER SEVERAL TIMES AND HAVE ALWAYS BEEN PLEASED BY THE PRICE, QUALITY, AND QUICK SHIPMENT. I WILL BUY AGAIN.
Process took about 10 minutes after reading the instructions.
Included photos showed exactly where everything was located.
Works perfectly.
Thanks
as with the hitch that was purchased, the installation was easy, and as the connector shipped with the hitch, the project was totally completed in 35 minutes. thank you
Curt could not have made it any easier. No cutting or splicing. Just follow the directions. Disconnecting the connectors can be a little difficult until you figure out how they work.
Trailer lights on my Tacoma stopped working so I picked up this wiring harness and with a simple installation got the lights working.
Works. Instructions could have been better. Could have come with some more zip ties, or better style of zip ties. Some of the cables could have been longer. Could have come with some replacement trunk liner fasteners because you will inevitably break some.
Works perfectlyEasy to install with no wire-cutting or splicing into electrical system. Perfect match for factory wiring - just unplug a connector and plug in adapter between.
Very simple to install. No splicing involved. Just open the trunk liner, disconnect both tail light connectors, and insert the new adapters. Secure with provided zip ties and two way tape then put the liner back in place. Takes about five minutes.
SIMPLE AND QUICK TO INSTALL. NO WIRE CUTTING OR SPLICING. I HAVE ORDERED A TRAILER HITCH AND A WIRING HARNESS FROM ETRAILER AND I AM VERY HAPPY WITH BOTH. THANKS.
after speaking to a service rep on the phone about installation, he was very helpful. I found installation to be a breeze. The trailer hitch and wiring were top notch I would recommend it to anyone.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.