SnowBear Proshovel Snowplow for 2" Hitches - Electric Actuator - 88" Wide x 26" Tall
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Part Numbers: SB324-140,33055
Our Price: $3,271.85
This item qualifies for Free Shipping
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
SnowBear Proshovel Snowplow for 2" Hitches - Electric Actuator - 88" Wide x 26" Tall
part number: SB324-140
Hitch-mounted snowplow makes short work of your snowy driveway or parking lot. Pivoting, 5-position blade glides over uneven ground. Long-lasting actuator with internal clutch lets you operate plow from your warm cab.
Features:
- Hitch-mounted plow lets you clear parking lots and driveways with your vehicle
- Plow sits close enough to vehicle to reduce leverage and strain on plow, mounts, and vehicle
- Electric actuator raises and lowers plow smoothly and consistently
- Internal clutch prevents damage caused by attempting to under- or overextend the actuator
- Simple, chain-lifting design has fewer moving parts than a winch
- In-cab toggle switch lets you raise and lower the plow from the comfort of your vehicle
- Includes a wireless remote control as an alternative to the toggle switch
- Adjustable, 5-position blade can be manually angled left, right, and straight ahead
- Manual release handle is easily accessible from front or back of plow
- Terrain-adjustable design for efficient plowing with less tripping
- Rocking blade pivots up to 6" to allow maneuvering over uneven terrain
- Trip springs and eyebolts are angled so blade rests on ground at correct angle
- Sturdy steel edge scrapes over a variety of solid surfaces - not for gravel or sand
- Poly scraper blade attachment (SB324-070 - sold separately) allows you to plow over grass or decorative pavement without worry of damage
- Skid shoes let you adjust plow height to prevent blade from digging into the ground
- Strong rubber deflector allows for better visibility by directing snow away from your windshield
- Red visibility markers help you see plow edges so you can steer away from obstacles
- Rugged and durable, all-steel construction
- Black powder coat finish provides corrosion resistance
- Simple installation
- Slides into your vehicle's 2" front trailer hitch receiver
- ISO certification ensures consistent, quality manufacturing
- Assembly required
- Made in Canada
Specs:
- Application: 2" x 2" front-mounted trailer hitch receiver
- Blade dimensions: 88" wide x 26" tall
- Height adjustment: 9"
- 5 Blade angles:
- Left 11 degrees
- Left 22 degrees
- Straight ahead
- Right 11 degrees
- Right 22 degrees
- Distance from bumper: 39"
- Actuator lift capacity: 1,000 lbs
- Weight: 390 lbs
- 1-Year limited warranty
Note: Due to the size of this item it ships via truck freight.
The SnowBear Proshovel conveniently slides into your vehicle's front-mounted trailer hitch for easy, convenient mounting. Smoothly and easily raise and lower the plow from the comfort of your cab with the remote-controlled electric actuator. The pivoting blade makes this plow ideal for rocky or uneven surfaces because it can adjust to the terrain. Angled trip springs are also built in to help keep the blade from catching and tripping. Being just 39" away from the bumper, the Proshovel snowplow has a compact yet strong and sturdy design.
Simple, Hitch-Mounted Installation
This hitch-mounted snowplow simply slides into your vehicle's front trailer hitch receiver, making it a breeze to install. Unlike a plow that attaches to custom-fit brackets, which ties you down to just 1 vehicle, this hitch-mounted plow can be used on most trucks or SUVs with a 2" x 2" front-mounted hitch. As a result, this plow can be easily switched between multiple vehicles. And because it offers a nearly universal fit, you won't have to buy a new plow when you replace your old vehicle.
To install the Proshovel snowplow, just slide the shank of the plow assembly into your 2" trailer hitch receiver . Then use a pin and clip or a hitch lock (sold separately) to secure the plow in the receiver.
How to Plow
Once the plow is mounted on your vehicle, lower the blade and set it to the desired angle. To set the angle, exit the vehicle and manually position the plow straight ahead, 11 degrees to the left or to the right, or 22 degrees to the left or to the right. Angling the blade allows you to push snow off to the side where you want it without having to change the angle of your entire vehicle. This is especially useful on a driveway or private roadway where piling the snow straight ahead would create a barrier.
To begin plowing, just drive forward. When backing up to take another pass, be sure to lift the plow with the remote or the in-cab toggle switch, then lower it again before moving forward. When approaching a large pile of snow, be sure to decrease your speed. Slamming into a pile of snow can void the warranty on the Proshovel.
When you are finished, put your vehicle in park and lower the plow. Remove the plow from your vehicle after every use.
Smooth, Controlled Lifting with Electric Actuator
The electric actuator on this plow allows you to lift and lower the blade using a toggle switch that mounts in your cab. You can also use the included wireless remote control. To raise the plow, activate the actuator. As the actuator moves along the internal screw, the arm on top of the actuator will pivot, raising the plow blade by pulling the chain that is attached to it. Having fewer moving parts than a typical winch makes this setup less complicated and less likely to break down than other plow lifting and lowering devices. There is also an internal clutch system that prevents damage to the actuator should you try to raise the blade too high or lower it too low.
Add-On Accessories
SnowBear offers a plethora of helpful accessories to make plowing even safer and easier. Along with the available accessories to enhance your snowplowing experience, many parts of the SnowBear Proshovel snowplow are available separately, so you can replace worn-out pieces without having to replace the whole plow.
The off-road halogen light kit (SB324-127) may be necessary if your plow blocks your vehicle's headlights. This kit will light up the way when you're plowing at night or in the early morning. The light kit mounts directly to your plow frame and offers increased visibility when plowing in dark conditions. The 2 bright halogen lights make it easier for you to see where you are going and for others to see you.
With the caster kit (SB324-126), it will be a breeze to move and store the Proshovel snowplow when it's not in use. These wheels mount directly behind the blade and they can be easily folded down for use and up for storage. In addition, these wheels will not weigh the plow down.
The drop extension kit (SB324-128) allows you to use your SnowBear snowplow on your lifted vehicle. With 6" of drop, this bolt-on kit ensures that the plow makes proper contact with the ground. Its sturdy steel construction is just as strong and durable as the plow itself.
If you are worried about causing damage to your lawn or pathway, the poly scraper attachment (SB324-070) is perfect for replacing the harsh, steel scraper on the Proshovel. The polymer construction is strong enough to still help plow efficiently, but gentle enough to not hurt your lawn or pathway.
324-140 Snow Bear Pro Shovel Snow Plow for 2" Hitches - Electric Actuator - 88" Wide x 26" Tall
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
part number: 33055
Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.
Features:
- Front-mount hitch provides attachment point for hitch-mounted accessories
- Winch, spare tire carrier, snowplow, cargo carrier and more
- No more blindly backing trailer in - just hook it up and drive it forward
- Custom fit is designed specifically for your vehicle
- Precision, robotic welding maximizes strength and improves fit
- Easy, bolt-on installation - no welding required
- Complete hardware kit and installation instructions included
- Lifetime technical support from the experts at etrailer.com
- Gloss black powder coat finish over steel resists corrosion
- Sturdy, square-tube design
- Assembled in USA
Specs:
- Line pull: 9,000 lbs
- Vertical load: 500 lbs
- Gross trailer weight: 5,000 lbs
- Receiver opening: 2" x 2"
- Pin hole diameter: 5/8"
- Limited lifetime warranty
etrailer.com Technical Support
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
33055 Curt Front-Mount Trailer Hitch Receiver
Customer Reviews
SnowBear Proshovel Snowplow for 2" Hitches - Electric Actuator - 88" Wide x 26" Tall - SB324-140
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" - 33055
Average Customer Rating: 4.7 out of 5 stars (58 Customer Reviews)
Hitch-mounted snowplow makes short work of your snowy driveway or parking lot. Pivoting, 5-position blade glides over uneven ground. Long-lasting actuator with internal clutch lets you operate plow from your warm cab. Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.by: Kevin I.10/06/2014
1996 Ford E-350
This hitch came quickly and I believe was priced fairly for what you get. Unfortunately, as some other have posted, this hitch is intended for my vehicle (1996 Ford E350 RV) but did not fit correctly. I had a problem with the front holes not being spaced far enough apart for the bolts to fit. The rearmost bolts go into a oversized and slotted hole in the underside of the frame so there was no problem with those, but the front holes in the frame have to be drilled out to 17/32" for the supplied 1/2" bolts per the included directions, and I couldn't get the bolts in both sides. The bolt holes in the hitch needed to be approximately 1/4" further apart. Also, there is a relief cut out of the hitch that I assume is to miss a bump on the under side of the frame. This cut out is in the wrong location to miss the bump in the frame. I went ahead and torched the slot for the bolt a little longer on one side and made the cut out for the frame bump bigger on both sides. A little grinding, a little touch-up paint, and back on she went. Had to notch the lower plastic valance just a little bit to clear the receiver, which was expected. Actually had to cut it a lot less than I thought I would. The two safety chain loops sit right under the valance, but I don't for see the need to hook anything to those, so I opted to not hack up the valance at this time. I intend to put a bike rack on the front, and also use the hitch to get drug onto the beach at Pismo from time to time. Hopefully the cuts I made don't weaken the hitch for that purpose. The directions call for this to be a 20 minute install. Granted, I took off the bumper, but even if I hadn't, and the hitch was fitted correctly, I find it hard to believe anybody could get this done in anywhere near that time. As another reviewer said, now that it's on, I'm a happy camper, but it was a little bit of a job to get there.
by: Stephen09/26/2023
2011 FordVan
The hitch is good quality but the hole pattern did not match my 2011 E150 Ford Van. The rear bolts fall in the access hole. I have to drill 3/4 holes in the frame instead of 17/32". I have to remove the whole front bumper because the accesshole is to small for the 1/2 carriage bolt.
by: Terry 05/04/2024
One of the best products I have ordered!
by: Robert H06/24/2020
Worked great for hauling my motorcycle on the front of my motorhome. Lets me pull my boat and have transportation when I get where I'm going.
Robert H.
6/25/2021
Its working out great and lots of people ask me about it.
by: Maddkeso04/24/2024
20 min install, remove bumper if you don't have a grinding tool.
by: Dan06/09/2022
2005 FordVan
1 hour install included removing the valance and all but two holes lined up due to some minor previous frame damage after using a little yankee ingenuity all fit like perfect didn't require removal the bumper at all and the fish wire technique worked perfect and recommend using blue lock tight. I highly recommend the Curt front hitch for a 2005 E350 Ford Econoline! Think I will leave the valance off like the look!
by: Alan04/06/2021
Had to remove front bumper, drill a couple of holes and bolt everything back on. I did wedge a piece of Styrofoam atop the bolts to prevent them from popping out. Installed the bumper and then the hitch, which I tst fit first. Everything looks great, no cutting on bumper plastic.
by: Dick M09/24/2022
2006 FordVan
Product seem adequate. The instruction were not accurate. See pictures.
by: David E.06/09/2015
Product shipped on time. Installation was straightforward. Using a Swagman Dispatch bike Rack with this front hitch on my Chinook RV--works well.
by: Dan 10/11/2014
2003 Ford E-450
Great front hitch .. Easy fit .. Remove front bumper "4bolts" makes the installation a breeze.. Fitted on my own in 1/2 hour ..
Ford E450 c class motorhome
by: Jim S08/06/2020
Easy order process.
Correct hitch and fit.
Would recommend etrailer.
by: david01/21/2013
1999 FordVan
i believe in spreading the word if something is either bad or good, but like a lot of people when something is good we simply start enjoying it and forget to pass along to others. the internet has been helpful with the "reviews" most companies have which has kept me from purchasing or purchasing depending on how the reviews were.
to the point; i have purchased several items from etrailer and have been truely amazed by both the customer service and the ease of purchasing.
the most recent item i purchased was a front receiver hitch for my van. even to me this is risky, how many people put receiver hitches on the front of their vehicles and an older one at that ('99). not only did etrailer have one, but there was a video on how to install it, really! the best part is it shipped the day i ordered it (sunday) and when i got it i saw that it was made in the U.S.A. frankly, i would have paid twice the amount if i would have known that.
i could go on. if you need something that this company carries and you are like me (want to get the best price), you'll look around on the internet, etc. but i assure you, you won't be dissapointed with the price (i got free shipping on a thing that weighs 40+ pounds), the customer service and the speed with the delivery.
highly recommend and i will look to this company before i go anywhere else.
thank you etrailer, you've earned my business by doing the right thing.
respectfully,
dave
David
7/28/2014
I stand behind what I said a year ago and the receiver is something I cant live without!I carry my bike rack on it, push my boat up my driveway with it and will soon be mounting a special lift to hold my motorcycle!Glad you care, thanks again,Dave
by: john b07/20/2014
1991 FordVan
the hitch arrived in excellent condition. altho the instructions state will fit e350 cut back rv it did not. my rv has a sway bar on the front-unk if stock or add on. fitting the hitch required extensive fitting and shimming, the bumper had to come off, two more holes drilled and two enlarged. the left (drivers) side rear hole would not accept enclosed bolt because there is a rise in the frame just above the hole and very limited room. I had to get longer bolts to fit thru the shims (one and a quarter longer) and used one half inch bolts on three of the mount holes. the fourth (rear drivers) would only accept 5/16 due to the restricted room and limited ability to enlarge hole more. the fit, even with adjustment, is very close. we are talking 1/16 to the steering arm. now that it is on im a happy camper but please do not underestimate the trouble. with or without sway bar should be included in ordering specs.
John B.
7/28/2015
doing well. just bought another curt product=receiver hitch gizmo that has the rack on top and can tow trailer with bottom. nice finish, quick service. happy camper-can take the boat and the junk!!! now will you please talk to the fish gods and get some production my way.
by: Greg V.06/27/2013
2007 Ford E-450
The Curt front receiver went on my 2007 Lazy Daze RV (Ford E450 chassis) without a problem. The forward holes in the frame must be enlarged but this was done easily. I would recommend you hold the receiver in position with a floor jack and carefully mark the location for the hole enlargement. A slight offset from the original hole centers worked the best for me. The bumper had to be removed to install the frame bolts and spacers since there were no access holes large enough in the frame. Once the bumper was removed (four bolts and a one person easy lift off) the frame bolts and spacers were easily installed without using the fish wire. The receiver fits below the plastic air dam without modification and you hardly notice it's there. Great product, great price!
Greg V.
12/26/2014
Front receiver works great for backing the boat down on those narrow landings. Its a little more work hooking and re-hooking the trailer but with a little space planning before hand everything works fine.
by: Gerald10/31/2022
Carol, the product does fit great. Was very difficult to drop in the four bolts as the opening in front of the Van frame is too small. I have to use a 1.5inch grinder to open up the hold for bolt to drop in. The fish wire work great. your instructions should add a note that partial removal of front bumper may be required in order to expose chassis frame to drop in bolt. Second, Four bolt pattern on Receive does not match up with holes in vehicle frame, had to use reamer to elongate passenger front bolt hole. Total time for install was 4.5 hours and a few swear words. The Vehicle i had issues with is a RV on a 2006 Ford E350 van frame. Gerry Savaglio
by: Frank06/19/2020
Perfect fit. Pro tip, loosen bumper no need to take it off. Guide wire and hardware fits in the gap. Also one man job made easy with floor jack to lift hitch and bumper( with wood block ) into place.
Frank
6/20/2021
Still working as new.. also what a great addition.. when I look at new class C’s it’s a must.
by: David05/11/2022
2022 Ford F-250 Super Duty
Summer storage in the driveway requires shade in hot central California. This 95 Firan Telstar has 10K miles so I have to keep it cool, 'cause it is cool.
by: Forrest B.10/23/2012
1998 FordVan
Well built product, came with the hardware to install. The only problem is the cut out for the bumps on the frame were off by 7/8 of an inch. I had to extend the opening on the mounting flange so that the unit would mount flush on the frame. Not too much of a problem.
Richard
6/25/2014
What bumps?
by: Carl04/21/2015
2003 Ford E-450
Because there was information here that this Curt hitch would fit a Ford E450 based RV (and it was cheaper than the Draw-Tite hitch), I purchased the hitch for my RV. However, because of the hump in the vehicle's frame as others have described, the Curt hitch would not fit flat against the frame of my 2003 E450 without cutting the hitch to enlarge its slot on its mounting flange. Regrettably (because the quality of the hitch looked to be superb), I returned the hitch to etrailer and am now waiting for the Draw-Tite hitch to arrive. I will write a review of that hitch once it arrives.
by: Jamie H.07/20/2017
2005 FordVan
Easy installation and fit perfectly on my 2005 Ford Class C RV. Make sure your drill bit is sharp. Used it for a carrier that hauled my KTM 400 EXC. Worked great and I had good visibility over bike. The bike did block the airflow and you could hear the radiator fan kicking on but the temp stayed in the normal range. etrailer's installation video is a big help as well.
by: Mark K09/16/2014
2007 Ford E-450
I installed this on my the front of my 2008 Four Winds Majestic 28 motor home. It's on a 2007 Ford E450 Chassis. As described it required making 2 frame holes larger. I had to losen, but not remove 4 bumper bolts to access inside of frame. The hitch was shipped quickly, showed up packaged perfectly, and was followed up by an email offering assistance if needed. The quality is great and and the holes lined up perfectly. I was able to install it by myself in about 45 minutes. I will buy from these guys again!
by: Glenn05/26/2015
1999 FordVan
Great hitch!
It's so convenient to carry bikes up front, leaving the rear accessible.
Heavy duty, powder coated, and excellent hardware.
Watch the video for the best directions. The paper one suggested the wrong hole. Be prepared to do minor grinding/expansion of holes to get things to fit perfectly. Clever use of the included fishwire makes pulling the bolts through a snap.
VERY happy with the hitch and end result! Keep up the great work!
by: Norman05/01/2018
2003 FordVan
Front mount 2" receiver hitch was a little tricky to install as the slotted frame hole had to widened a little to allow the bolt heads to slip thru....Once that was done everything bolted right up and now a can move my trailer and boat around and actually se where they are. Installed on 2003 Lazy Daze Motorhome on a Ford E450 chassis.
by: Betty 05/19/2020
When I contacted Etrailer, I got excellent customer service. I was looking for a hitch for the front of my Class C motorhome. The representative told me which kind of hitch I would need to accommodate my RV. My package arrived on time. Iam very happy with my purchase. This is my second purchase from Etrailer.
by: Chris12/10/2014
1997 Ford Club
The package arrived quickly. The installation movie was a great help. I had the same issue they showed in the movie on my 1997 ford club van. I had to use a dremel tool to widen the holes in the frame to insert the bolts. Hitch works great. I'm using it to hold my bike rack when I pull my trailer.
25
58
Show More Reviews Ask the Experts about this Snow Plow
Do you have a question about this Snow Plow?
- SnowBear Proshovel Snowplow # SB324-140 Shipping Weight and Number of Boxes
- The SnowBear Proshovel Snowplow for 2" Hitches # SB324-140 has a shipping weight of 390 lbs. We drop ship this product from the manufacturer and it comes in 3 boxes that are between 75 and 150 lbs each. My contact couldn't give me a specific on individual box weights. It comes with 3 boxes on 1 skid but does not require a forklift as the 3 boxes can be individually lifted separately if desired.
view full answer... - Height of Front Hitch Receiver for SnowBear SnowPlow
- The SnowBear Proshovel Snowplow for 2" Hitches - Electric Actuator - 88" Wide x 26" Tall item # SB324-140 needs to be mounted 9"-10" above the ground. There is an extension kit if your Ford F-250 is lifted or sits to high. It is the Drop Extension Kit for SnowBear Snowplows - Bolt On - 3" Drop item # SB324-128. This bolt-on kit ensures that the plow makes proper contact with the ground. Its sturdy steel construction is just as strong and durable as the plow itself.
view full answer... - Snowplow that Fits a Front Mount Hitch Receiver on a 2017 Ford F-150
- For your 2017 Ford F-150 I recommend the SnowBear Proshovel plow, # SB324-140. This plow fits into a 2 inch hitch receiver. It has an electric actuator to raise and lower the plow from inside the truck cab so you won't have to get in and out of the truck to raise and lower the plow. It also comes with a wireless remote which you can use instead of the toggle switch if you want.
This plow also has 5 plow angles and 9 inches of vertical adjustment. The plow weighs 390 pounds so make sure
view full answer... - Recommended Front Hitch and e-Bike Rack for 1996 Airstream RV on Ford E-350 Chassis
- We can definitely get you set up for this application.
For the E-350 chassis your 1996 Airstream is built on, the Curt Front Hitch # 33055 will work perfectly. It's designed specifically to fit this chassis but note that some minor drilling will be required during installation. I've attached the complete installation manual below.
Then for a bike rack that will fit this hitch and work great with your e-bikes, I highly recommend the Swagman E-Spec # S94FR. This durable carrier can
view full answer... - Front Hitch Needed for a 2000 Ford E-450
- The Curt Front Mount Trailer Hitch Receiver # 33055 that you referenced fits Ford Vans (up to an E-350), but since your Chateau is on a 2000 Ford E-450 you would need to go with the Draw-Tite # 65001.
Installation instructions and a photo showing the mounting hole locations for the Curt option have been added for you to check out. I am doubtful that the Curt will fit but you can use the photo to check your vehicle for a fit.
view full answer... - 2005 Ford E-450 RV Forest River Front Hitch for Carrying Bike Rack
- Yes we have the Curt front hitch part # 33055 as a fit for your 2005 Ford E-450 RV. You could mount a bike rack in this like with the Hollywood Racks Trail Rider # HR200Z for a high quality and cost effective platform style bike rack.
view full answer... - Can you Overload a Front Mount Hitch on a 2007 Ford Van E-450 RV Cutaway
- The Curt Front Mount Trailer Hitch, part # 33055, is in fact the highest tongue weight capacity available for your 2007 Ford Van E-450 RV Cutaway.
As for loading the hitch over its tongue weight capacity, that is something that I do not recommend doing. One problem you would have with that is, as you said, the high possibility of hitch failure (whether the hitch breaks, bend, or is ripped from its bolts).
Another possible problem is tipping or sagging your motorhome in the front.
view full answer... - Highest Capacity Bike Rack for Mounting on a Motorhome
- The only bike rack capable of being mounted behind a motorhome and able to accommodate two 63 lbs e-bikes and your sons 30 lbs bike is the Thule T2 Pro XTR Bike Rack for 4 Bikes - 2" Hitches item # TH69TX. The Thule can carry up to 160 lbs but you have to have the full extension installed to reach this capacity. The extension is included but it is also removable.
view full answer... - Does Curt Front Hitch, # 33055, Require Any Cutting Of Front Air Dam On A 1999 Ford Van
- The Curt Front Hitch, # 33055, on a 1999 Ford Van does not require any cutting of the front valance (air dam), but you do need to remove the front valance from the bumper.
Also, the two front holes in the frame rails need to be enlarged. Then, you will use the fishwire (included) to install the 4 bolts and spacers into the holes in the frame. Then, you just need to attach the hitch to those bolts and torque to 75 ft. lbs.
I am sending a video link that will show you how to use the
view full answer... - Front Hitch Recommendation for a 1997 Ford E-350 Motorhome
- For your 1997 Ford E-350 Cutaway built into a motorhome you would want the part # 33055 as it is a confirmed fit.
view full answer... - Front Mount Trailer Hitch Receiver For a 2006 Forest River Lexington 255DS E-450 RV Cutaway Chassis
- The Curt Front Mount Trailer Hitch Receiver # 33055 is confirmed to fit the Ford E-450 RV Cutaway chassis that is under your 2006 Forest River Lexington 255DS.
I recommmend using either the etrailer Rubber Hitch Cover # 22282 or WeatherTech BumpStepXL Hitch-Mounted Bumper Protector and Step # WT81BS1XL to fill the receiver hole and eliminate the whistle it often creates. The step is great as it will give you that added reach when cleaning your RV.
view full answer... - Bolt Hole Spacing of Curt 33055 Front Mounted Receiver
- The Curt # 33055 you mentioned isn't a fit for the 1991 F-250, it's a fit for the E-Series Vans, which Curt confirms. Unfortunately, they don't offer a front mounted hitch for your truck.
The bolt hole spacing I was able to obtain is as follows:
• Side to side bolt hole spacing for front-most holes closest to the receiver, 37.969 inches, center to center
• Side to side bolt hole spacing for rear-most holes closest to the engine, 38.469 inches, center to center
• Hitch drop or vertical
view full answer... - Can Replacement Install Hardware for Curt Front Hitch # 33055 be Ordered
- We sell replacement hardware for all of the hitches we carry with the part # RHK. You'd just need to select the hitch manufacturer from the drop down menu and then enter the part number for the hitch that you have and we'd send you what you need.
view full answer... - What Front Receiver Hitch Will Fit My 1994 Ford E-350 RV Cutaway
- Your 1994 Ford E-350 RV Cutaway is compatible with the Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2", part # 33055. This front hitch receiver has a maximum tongue weight of 500 lbs and a maximum gross trailer weight of 5,000 lbs.
I have included a product description link and a video installation link below.
view full answer... - Front Mounted Trailer Hitch Receiver for Motorhome on 1990s Ford E-350 Econoline
- We have a potential solution for you, though the part you referenced is a multi-fit hitch for the rear of some passenger vehicles and will not work with your motorhome on an E-350 Econoline. You never mentioned what year your vehicle was but based on my research it is very likely to be a 1990s model.
For that, the hitch that fits is the Curt Front Mount Trailer Hitch Receiver # 33055.
This hitch will fit a 1991 through 1998 Ford E-350 Econoline, and I have added a link to the installation
view full answer... - Front Mount Trailer Hitch for 1994 Ford Club Wagon
- The Club Wagon is simply a different name for the Econoline of the Ford van, and we do have a front mount trailer hitch that fits a 1994 Ford Club Wagon, so long as it is the E-150, E-250, or E-350 model, which it should be.
For that, the correct fit is the Curt Front Mount Trailer Hitch Receiver # 33055.
I have added a link to the installation instructions as well as a link to an installation video for you to take a look at.
view full answer... - Recommended Front Hitch for Fleetwood Tioga 31 Class C Motorhome on Ford E-450 Chassis
- The Curt Front Mount Trailer Hitch Receiver part # 33055 is what I recommend for a Fleetwood Tioga 31 Class C Motorhome on Ford E-450 Chassis.
view full answer... - Recommended Front and Rear Mount Hitch for a 25 Passenger E-450 Shuttle Bus
- I am not sure what year the chassis is but if it's anywhere between 1991-2007 then you can use the Curt Front Mount Trailer Hitch Receiver part # 33055 which is a fit for a E-450 Cutaway Chassis. Then for the rear, you wouldn't have any direct bolt-on options but the Draw-Tite Ultra Frame Service Body Trailer Hitch part # 41990-16 could be welded-on or bolted once drilled.
The most amount of bikes we offer for a single rack is six, the Yakima HangOver 6 Bike Rack part # Y02485 which
view full answer... - Will Curt Front Hitch, # 33055, Fit A 2007 Ford E-450 Chassis For A Motorhome
- I have the Draw-Tite Front Hitch, # 65001, which will fit on the 2007 Ford E-450 Chassis.
The Curt Front Hitch, # 33055, only lists fitment up to the E-350 van. I called the supplier (Curt) to see if it will fit your 2007 Ford E-450 Chassis and they said that you would have to do a couple of measurements to see if it would fit.
The measurement of the mounting holes from center to center on the front hitch is 38-1/2 inches. On your van chassis if you measure across from frame rail
view full answer... - Front Mount Hitch Receiver for a 2004 Coachman Roadmaster on a Ford E-450 Van Chassis
- Whether the Ford E-450 van chassis is a 2002, 2003, or 2004 (or anything in the 200 to 2007 model year range) it will take front mount receiver # 65001. So no worries, we got you covered!
The Curt hitch, # 33055, is indicated as a fit for the E-350 but not the E-450. There can be some subtle differences between the two. That is why I recommend 65001 because it does fit the E-450 for sure. I have linked a video showing an example installation for you.
view full answer... - Front Mount Trailer Hitch Receiver For a 2003 Ford E-450 RV Cutaway Chassis
- The Curt Front Mount Trailer Hitch Receiver # 33055 is the part you are looking for to fit your 2003 Ford E-450 RV Cutaway chassis.
I recommend using a etrailer Rubber Hitch Cover # 22282 to cut down on the whistle that often comes from having an open receiver tube. If you are using this for a carrier the Curt Anti-Rattle Hitch Clamp # C27UR will allow you to remove the excess play so your carrier isn't rattling around while you drive.
view full answer... - 2005 Forest River Sunseeker Class C Front Hitch Recommendation
- Your 2005 Forest River Sunseeker Class C motorhome would be built on a 2005 Ford E450 Cutaway chassis so the correct front hitch would be the part # 65001.
You will need to enlarge a hole in the frame and then use a pullwire (included) to get the hardware to line up properly. These are pretty standard hitch install steps that wouldn't be too hard at all.
view full answer...
Info for these parts were:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Expert Research:
Adam R
Written by:
Lindsey S
Updated by:
Adele M
Updated by:
Wilson B
Updated by:
Kristina F
Updated by:
Isabelle B
Video by:
Andrew L
Video by:
Ryan G
Test Fit:
Shane T
Test Fit:
Thomas T
Video Edited:
Sue W
Video Edited:
Chris R
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Brooke M.
9/28/2023
It looks like this hitch isnt a fit for a twenty eleven Ford van. We do have part # 31053 that is a confirmed fit for the van you have.