Detail K2 Snowplow for 2" Hitches - 88" Wide x 26" Tall
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Part Numbers: K2AVAL8826,65046
Our Price: $2,240.05
This item qualifies for Free Shipping
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near meDetail K2 Snowplow for 2" Hitches - 88" Wide x 26" Tall
part number: K2AVAL8826
Hitch-mounted residential plow has shock-absorbing springs and a steel-edge blade to easily clear driveways and parking lots. Remote-controlled electric winch lets you raise or lower the 3-position blade from your cab.
Features:
- Hitch-mounted snowplow lets you clear paved and gravel parking lots and driveways with your vehicle
- Electric winch raises and lowers plow with sturdy, nylon strap
- 2.4 GHz Wireless remote control allows you to operate the plow from the comfort of your vehicle
- In-cab switch serves as a reliable backup to the remote control
- Adjustable, 3-position blade can be manually angled left, right, and straight ahead
- Strong rubber deflector on top of plow directs snow down and away from your windshield
- Hardened steel edge breaks up packed snow and ice
- Skid shoes let you adjust plow height to scrape over gravel and uneven surfaces
- Shock-absorbing springs let plow tip forward on impact to protect you and your vehicle
- Can extend life of the plow if you hit an obstruction
- Blade stiffeners provide 2 additional points of contact between the plow and your hitch for a sturdy connection
- Red visibility markers help you see plow edges so you can steer away from obstacles
- Flip-down caster wheels allow you to roll the plow where you need it for mounting or storage
- Wheel height is adjustable to match your vehicle height
- Plow handle with knob lets you easily move plow up and down during mounting
- Safety chain holds plow in raised position during travel
- Reinforced, all steel construction has black, rust- and UV-resistant powder coat finish
- ISO certified
- Simple installation
- Slides into your vehicle's 2" front trailer hitch receiver
Specs:
- Application: 2" x 2" hitch receivers
- Cannot be used with hitches or receiver adapters that have built-in drops
- Blade dimensions: 88" wide x 26" tall
- 3 Blade angles:
- Left 45 degrees
- Straight ahead
- Right 45 degrees
- Distance from center of hitch pin hole to the front edge of plow: 50"
- Winch lift capacity: 3,000 lbs
- Weight: 296 lbs
- 1-Year limited warranty
The Detail K2 snowplow conveniently slides into your vehicle's front-mounted trailer hitch for fast, simple mounting. Easily raise and lower the plow from the comfort of your cab with the remote-controlled electric winch. The pivoting blade makes this plow ideal for rocky or uneven surfaces because it can adjust to the terrain.
Simple, Hitch-Mounted Installation
This hitch-mounted snowplow simply slides into your vehicle's front trailer hitch receiver, making it a breeze to install. A plow that attaches to custom-fit brackets ties you down to just 1 vehicle. But this hitch-mounted plow can be used on most trucks or SUVs with a 2" x 2" front-mounted hitch. As a result, this plow can be easily switched between multiple vehicles. And because it offers a nearly universal fit, you won't have to buy a new plow when you replace your old vehicle.
To install the snowplow, just slide the shank of the plow assembly into your 2" trailer hitch receiver (sold separately). Then use a pin and clip or a hitch lock (sold separately) to secure the plow in the receiver.
The snowplow comes with flip-down caster wheels that make the installation process even easier on you. Simply flip the wheels into position and you will be able to roll the plow into position for mounting or storage. The height of the wheels can also be adjusted to match the height of your vehicle.
How to Plow
Once the plow is mounted on your vehicle, lower the blade and set it to the desired angle. To set the angle, exit the vehicle and manually position the plow straight ahead, to the left, or to the right. Angling the blade allows you to push snow off to the side where you want it without having to change the angle of your entire vehicle. This is especially useful on a driveway or a private roadway where piling the snow straight ahead would create a barrier.
The plow comes with a wireless remote that allows you to stay warm and out of the elements while still effectively controlling the plow. The remote operates on a 2.4 GHz frequency, allowing it to quickly send signals to the winch without experiencing delays. And because it's wireless, you won't have to run wires through your dash. Nor will you have to leave your window cracked open in the middle of a snow storm just so that you can run a wired remote into your cab. You will be glad to have it on those cold winter days.
To begin plowing, just drive forward. When backing up to take another pass, be sure to lift the plow with the remote, then lower it again before moving forward. When approaching a large pile of snow, be sure to decrease your speed. Slamming into a pile of snow can void the warranty on the snowplow.
When you are finished, put your vehicle in park and lower the plow. Remove the plow from your vehicle after every use.
Easy Lifting with Electric Winch
The electric winch on this plow allows you to easily lift and lower the blade using the wireless remote control. If you prefer, you can also install the included in-cab toggle switch to control the plow. The winch uses a durable strap, which is much quieter than a chain, to raise and lower the plow.
Detail K2 Features
The snowplow features skid shoes that allow you to adjust the height of your plow. This allows you to efficiently plow over surfaces that are uneven, such as gravel roads.
Blade stiffeners, or blade support brackets, reinforce the connection between the plow and your vehicle. They add 2 additional points of contact with your hitch on either side of the plow's T-frame. This prevents stress on the frame and on your vehicle, while also strengthening the performance of the plow.
Shock-absorbing springs allow the plow to dip forward in the event that you hit an obstruction. This flexibility protects you and your vehicle from impacts.
AVAL8826 Detail K2 Hitch Mount Snow Plow - 88" Wide x 26" Tall Blade
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
part number: 65046
Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.
Features:
- Front-mount hitch provides attachment point for hitch-mounted accessories
- Winch, spare tire carrier, snowplow, cargo carrier and more
- No more blindly backing trailer in - just hook it up and drive it forward
- Custom fit is designed specifically for your vehicle
- Computer-aided, fully welded steel construction ensures strength and durability
- Tested Tough - safety and reliability criteria exceed industry standards
- Easy, bolt-on installation - no welding required
- Complete hardware kit and installation instructions included
- Lifetime technical support from the experts at etrailer.com
- Black powder coat finish covers e-coat base for superior rust protection
- Sturdy, square-tube design
Specs:
- Line pull: 9,000 lbs
- Vertical load: 500 lbs
- Gross trailer weight: 5,000 lbs
- Receiver opening: 2" x 2"
- Pin hole diameter: 5/8"
- Limited lifetime warranty
Draw-Tite Tested Tough
Draw-Tite's Tested Tough program provides testing standards far superior to those outlined by the Society of Automotive Engineers (SAE), the go-to source for engineering professionals.
Each Draw-Tite trailer hitch receiver undergoes extensive fatigue testing and static testing with the ball mount that is either supplied or recommended for use with that particular hitch, thus ensuring results that are applicable to real life use. Fatigue testing is also conducted on hitches rated for use with weight-distribution systems.
In addition, Draw-Tite performs static testing on a simulated automobile, as opposed to the rigid fixture used for SAE testing, resulting in a more true-to-life scenario.
etrailer.com Technical Support
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
65046 Draw-Tite Front-Mount Trailer Hitch Receiver
California residents: click here
Customer Reviews
Detail K2 Snowplow for 2" Hitches - 88" Wide x 26" Tall - K2AVAL8826
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2" - 65046
Average Customer Rating: 4.6 out of 5 stars (112 Customer Reviews)
Hitch-mounted residential plow has shock-absorbing springs and a steel-edge blade to easily clear driveways and parking lots. Remote-controlled electric winch lets you raise or lower the 3-position blade from your cab. Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.by: Michael04/03/2024
It was a bit harder to put on than they show in the video. Did it by myself, everything fit perfect SO OWSOME! I would recommend anybody. Truck or car should add one. Very convenient and can be use for many different purposes.the rack on the back, I now put in the front with generator gas tools and it works as steps. So now I can tow trailer, or jet ski. Having that front hitch is so cool. You could even attach a car whinch in the receiver.
by: HydroTom12/29/2023
2006 Dodge Ram Pickup
Got this on my 2006 2500 Ram. I did avoid drilling the holes over 1 inch (suggested in the directions) by loosening the bumper bolts and prying out some brackets in the frame ends temporarily (just to get the bolts fished thru). I pushed the brackets back in after getting the bolts in place (and believe the bumper bolts will squeeze them to hold them), but I did bend some tabs that I can't get back to original.
My bumper bolts on the driver side wouldn't go in far enough (hitting a cooler) to be totally flush for a completely vertical lift into place, so I had to swing it up there first, then do the passenger side.
The first pair of bolt fishing went good, but then I had trouble getting the wires off the bolts (they were tight enough that the more I tried to twist them off, the tighter they gripped it). So instead of them coming off like twisting a nut off, I ended up peeling them off (with the bolts staying stationary and my peeling the wire around them). That slightly bent the wires so they were slightly bigger than the threads and while fishing the second set, the wire didn't stay in the threads and jammed the bolt in the hole a bit (but I still got them in place). So watch how you treat the fishing wires until done.
I already have a winch mounted on a hitch bracket, but may use this for more things besides that.
by: Russell12/21/2023
It wasn't fun to install by myself, but managed to do it in a few hours. Worked out great so far, I've hauled motorcycles on hitch carrier for about 2k miles so far and had no problems.
by: Douglas H.06/19/2012
2005 Dodge Ram Pickup
The instructions were good but could be printed larger for those of us with old eyes. The YouTube video was excellent and gave me the confidence to perform the installation myself. This front hitch is just what I needed to use for a canoe carrier over the front of my truck. Thank you.
by: George04/17/2024
2007 Dodge Ram Pickup
THE FIRST ONE WAS WRONG. THEY WERE VERY GOOD IN FIXING THE PROBLEM I'm 86 so it took me a little LONGER to install. I LIKE HOW IT LOOKS, WILL NOT USE IT TILL NEXT DEER SEASON. I can put a winch on the front or on the back.
by: Dale02/16/2024
Appears to be a solid, well made product. Had a slight bend to one of the mounting brackets that looked to have occurred during shipping, easily corrected. All the hardware was included and appears to be sufficiently sized. Included instructions were clear and well written.
The product was actually delivered ahead of scheduled date and the total price was reasonable. Well satisfied thus far.
by: Mike01/13/2024
2008 Ford F-150
Bought this DK2 plow in Jan 2023, and naturally we had no more snow the rest of the winter. Just got to use it last week after getting a foot of snow. Worked great, easier than I expected. The written instructions could’ve been a bit clearer on how to attach the assembled plow to the truck, but it was easy enough to figure out. Very happy with the purchase
by: Paul04/01/2018
2018 Dodge Ram Pickup
I have an 06 Dodge Ram Mega and product installation was really easy to do. Though I am a savvy "project guy", this was something I had never done before, and good for me as I was able to get a new drill out of the deal from the wife. With the existing upper bolts (18mm) incorporated in the installation, it is a great way to hold the receiver frame in place while drilling the four half-inch holes in the lower truck frame. I gave the two bolts a squirt of never seize overnight and they came off using my long, half-inch drive breaker with an 18 mm socket. With the two bolts off, I added the spacer and hung one side. On the other side, I used a pry bar on the opposite side of the frame (where the two bolts are connected with a flexible strip) to suck the bolt in (after putting on the spacer) long enough to push it up into place. This saved me from having to loosen all four nuts. Next, I used a $44.00 "Unibit" to enlarge the existing holes in the frame to pass the hardware through. After that, I drilled the (4) half-inch holes with the frame in place, passed the hardware through, and tightened everything with the last two nuts being the upper, existing ones (after the receiver was tight to the bottom of the truck frame with (4) bolts). I am certain this new receiver will give me options for carrying my generator, dirt bike, or what have you! Can't wait to get on the road!
by: Kyle03/01/2017
The only reason I didn't give 5 stars is the acces holes they want you to drill in your frame. I didn't drill them, I used a fish tape and pulled thru. Be aware tho some frames have mounting boss supports thru the inside of frame the bolts will get hung up on.
Other then that hitch works great. Two thumbs up.
by: Bryan06/22/2021
2004 Ram 2500
I got the hitch for a 2004 dodge 2500. I put it on the front of the truck to haul a motorcycle. It works great and all you can see is the hitch opening. Works great.
by: Chad 01/10/2023
2017 Ford F-350 Super Duty
Excellent for a home plow! Does the job but hard to use in heavy wet snow but good for the average snow fall
by: JimK08/10/2017
The installation was very straightforward using jack stands and a floor jack. Rather than drill the large hole in the frame per the instructions, I used a cutting torch and elongated an existing hole in the frame so the washer and bolt would just sneak through.
The receiver sits just below the front "air dam" below the bumper. On a 4x4 this is no problem. Check your clearance on a 4x2, you'll lose about three inches of clearance below the air dam.
I'm very pleased with the fit and finish of the hitch.
by: Keith 10/07/2023
The installation was a breeze, the instructions were great. The hitch fit my truck perfectly.
by: John03/22/2022
2003 Dodge Ram Pickup
Prettt easy to install after watching a you tube video on it. Immediately hooked my winch up to it and pulled an 8k pound rock with it. Receiver hitch held up perfect.
John
3/23/2023
Still holding up great
by: Jan M.06/17/2019
Directions were exactly what needed to be done, only set back was needing to drill a 1 1/4 inch hole, used a torch because I didn’t have a drill bit big enough, but it needed to be done so not complaining
by: Bruce06/16/2023
There were a couple of parts missing. When I contacted them they were very helpful. I received the parts two days later!
by: Barry 03/13/2023
I have had the hitch for over year pushing back my 30' trailer has never been this easy. I am so glad that your company has built one to aid the ease of use.
by: Dave G01/15/2021
After I got the front hitch installed, the plow assembled and hooked up I spent a little time tweaking the skid plates to keep the plow just off of the gravel. Works great for our 100 yard driveway and parking area.
by: Craig01/15/2017
2006 Chevrolet Silverado 2500
I received the Erickson Big Bed Load Extender and Draw-Tite Front Mount quickly the people at etrailer kept me in the loop when there was a chance that the Front Mount may be late because the manufacturer had not sent stock. This did not become and issue but they called me ASAP when they knew they did not have stock. Nice Service!!!!!!!!!!!
I do have a suggestion when installing the Draw-Tite Hitch. The directions say to drill or cut a 1 1/4" access hole in the side of the frame rail to have access when installing the 1/2 in bolts and plate. This is not necessary in my 2006 Dodge 2500 truck. Make a 12" snake out of a piece of copper wire from some Romex. Make a loop in the end and after drilling the 1/2" lower mounting holes in the frame, snake the wire thru the 1/2" hole to the front of the frame rail. Attach the wire that is in the kit to the snake wire and pull it thru the front of the rail to the 1/2 in drilled holes.
This procedure makes the installation much easier,saves time and DYI'ers do not have special tools to drill such a large hole.
Hope this tip helps.
Craig
1/15/2018
Have been using product to carry Kayaks on front of my truck with a 5th wheel hooked to the back. Nice setup
by: DaveS09/11/2017
2004 Dodge Ram Pickup
Very high quality receiver. I would recommend this unit. As with most after market parts a small amount of fab work is required for a clean installation. I am planning on hauling bikes on the front of my 1Ton Dodge Ram with my camper on the back. As strong as this unit appears I would not hesitate to put my 400CC motorcycle on the front also.
Daves
9/11/2018
After a year of hauling bikes, motorcycles and other racks I could not be happier with this product. Yes it does sit a little lower than not having a receiver, I have scraped it a few time. My DRZ400 rides fine and I am not worried it will bend or fall off. I have made over a dozen trips using this hitch.
by: David09/08/2023
Very simple to install. But i am a mait mech.
Fit perfect on my dodge 2007 3500 4x4 mega cab diesel.
by: Steve 08/16/2023
Nice but needed drilling so required professional install.
by: Lawrence08/09/2023
The hitch sat so low I had to remove it.
by: Dave02/16/2023
The hitch is suitable, however, it rides too close to the ground. I would not recommend this product.
by: John P.06/17/2019
2019 Dodge Ram Pickup
It has been one year since purchase, and I unpacked it and all looks good. I have not installed it, as one year ago I restarted a graduate degree online and that takes most of my time with a full time job. Check back with me January 2020, as I will install most likely over holidays 2019.
Backing short trailers or my boat trailers, cannot see trailer until it is going the wrong way in the door mirrors, in my stock 4x4 2004 Dodge Ram. I want to hook trailers to move them short distances, on my property or a non-crowded boat ramp with front hitch, always wanted to try it. Also will move my dirt bike on front hitch, without dirt bike blocking brake lights as with using rear factory installed hitch and dirt bike carrier. Will use in daytime as now front hitch receiver and dirt bike might block headlights. Check back early 2020 if you want results after I install it and use hardware and instructions. Sorry that in one year no install yet, been busy and really do not/did not need it right now. Thanks.
25
112
Show More Reviews Ask the Experts about this Snow Plow
Do you have a question about this Snow Plow?
- Required Hitch Height of Detail K2 Snowplow for 2 Hitches 88 Wide x 26 Tall
- The Detail K2 Snowplow for 2" Hitches part # K2AVAL8826 will require a hitch height between 13" - 18". This is measured from the ground to the bottom of the receiver opening.
In regards to a 2005 Ford F-150, the Curt Front Mount Trailer Hitch Receiver part # 31352 will put you in range so that's what I recommend.
view full answer... - Front Mount Hitch Receiver Options for a 2009 Dodge Ram 3500
- We do!
The Draw-Tite Front Mount Trailer Hitch Receiver # 65046 will sit just below your front bumper while the Curt Front Mount Trailer Hitch Receiver # C31017 requires you to cut out some of the bumper for the installation.
Both work great so it just depends on where you want the receiver located. Cutting into the bumper doesn't sound appealing, but a lot of people prefer that to a lower ground clearance when the receiver is below the bumper.
view full answer... - Is Drilling Required to Install Draw-Tite Front-Mount Hitch 65046 on 2005 Dodge Ram Pickup
- Draw-Tite front-mount hitch # 65046 is a confirmed fit for your 2005 Dodge Ram 2500 or 3500 series pickup. Drilling two 1-1/4-inch access holes on each side of the frame is a requirement for getting the included hardware into place; you'll want to use a 1-1/4-inch hole cut saw for this. The written instructions and a video showing installation in a 2007 Ram are both linked for you.
If you'll be using a snow plow in the hitch you might want to consider from front suspension support to
view full answer... - Replacement Mounting Hardware for Draw-Tite Front Mount Trailer Hitch
- Absolutely!
For a complete replacement hardware kit for your Draw-Tite front hitch, you will just need part # RHK. Once on the product page you will simply type in the model number of your hitch and select the manufacturer from the drop-down menu. For example, if you have the Draw-Tite # 65046 hitch that you were looking at, simply type in "65046" in the Hitch Item Number box and select "Draw-Tite" in the manufacturer box.
view full answer... - Front Mount Hitch for a 2020 Chevy Express 4500 Cutaway Van
- I reached out to my rep at Curt and was able to get a couple of options for you. Both of these are going to require some modifications because there is no custom fit front hitch available for your 2020 Chevy Express 4500 Cutaway Van. Your best bet is to use the Curt Adjustable Trailer Hitch Receiver item # C13701. This hitch will fit frame widths of 18" to 51" you can either use the included hardware to bolt the hitch to the frame, which will require drilling, or you can have a certified
view full answer... - Front Mounted Receiver Location When Installed on 2004 Dodge Ram 3500
- The Draw-Tite # 65046 front mounted receiver will fit the 2004 Dodge Ram 3500.
When the hitch is installed, the receiver tube will butt up against the underside of the front bumper fascia, a few inches below the license plate, as you'll see in the photo I provided.
The Curt # C31017 would sit about 2 inches higher, meaning you'd need to notch the bumper fascia, but you'd still be well under the license plate.
I've linked you to installation instructions for both hitches, as well
view full answer... - Will Front Mount Hitch Install The Same On 2004 Dodge Ram 2500 As On 2007 Dodge Ram Truck
- The Draw-Tite Front Hitch, part # 65046 would install the same on your 2004 Dodge Ram 2500 as it shows in the attached video for the 2007.
You can check out the attached installation instructions.
view full answer... - Front Mount Hitch Receiver for a 2003 Dodge Ram 3500 4x4 Laramie
- I checked with Draw-Tite and front mount hitch # 65046 does not exclude Laramie models of the 2003 Dodge Ram 3500. Curt hitch # C31017 excludes Laramie models on the 3500 series.
However, for the Draw-Tite hitch one customer said that the tow hook brackets required some modification to provide clearance for the hitch (3mm grinding).
view full answer... - Will Draw-Tite Front-Mount Hitch # 65046 Fit 2006 Dodge Dually 3500
- The Draw-Tite Front Hitch, part # 65046 is a fit for your 2006 Dodge 3500 Dually. This hitch has a 2 inch by 2 inch receiver opening and can be used for a cargo carrier, a spare tire carrier, snowplow, or possibly a winch. This is a custom designed hitch that is a bolt-on installation. All hardware and instructions are included. I have attached an installation video for this hitch.
You did not mention how you plan on using this hitch so I have attached some links to items you may be
view full answer... - How Low Does the Draw-Tite Front Hitch 65046 Sit On a 2003 Dodge Ram 3500
- The Draw-Tite Front Mount Trailer Hitch Receiver part # 65046 is designed to sit flush with the underside of the lower bumper fascia skirt on a 2003 Dodge Ram 3500. I have attached a photo which shows this. It sits as close to the underside of the bumper as possible without trimming.
If you're looking for an option that does not sit as low as the above, we do offer others such as the Curt Front Mount Trailer Hitch Receiver part # C31017 but this requires trimming of the bumper fascia skirt.
view full answer... - Can Access Holes for Installing Draw-Tite 65046 Front Receiver Be Drilled on Outside of Frame
- I checked with my contact in the Tech Services department at Draw-Tite, and was told that it would indeed be acceptable to drill those 1-1/4 inch access holes on the outside of the truck's frame members if necessary.
view full answer... - Will Draw-Tite Front Mount Trailer Hitch # 65046 Fit 2009 Dodge Ram 3500
- The Draw-Tite Front Mount Trailer Hitch Receiver # 65046 referenced in your question is indeed confirmed to fit your 2009 Dodge Ram 3500 4WD. This front-mounted hitch will provide you with a 2 inch receiver opening and it features a 500 pound vertical load limit and a 9,000 pound line pull capacity.
I have attached an installation video on the 2007 Ram, along with the written installation instructions that you can take a look at.
view full answer... - Does Draw Tite Front Hitch # 65046 Come with Install Hardware
- Your Draw Tite hitch part # 65046 most likely did come with install hardware but it's pretty easy to miss it. Check in the hitch opening and in the crossbeam tubing. A lot of times it's stuffed pretty far in there and difficult to see.
view full answer... - Will the Draw-Tite Front Mount Hitch 65046 Fit a 2003 Dodge Ram 3500
- Yes, the Draw-Tite Front Mount Trailer Hitch Receiver # 65046 that you referenced will work on your 2003 Dodge Ram 3500. I attached an installation video and instructions for this product for you to check out also.
view full answer... - Availability of Replacement Install Hardware for 2009 Dodge Ram Draw Tite Front Hitch
- Yes we do sell replacement hardware for all of the hitches we carry with the part # RHK. The install instructions for the # 65046 are linked on this page too.
view full answer... - Will the Front Mount Draw-Tite Hitch for a 2005 Dodge Ram 2500/3500 Fit a 1500
- The correct Draw-Tite Front Mount Trailer Hitch Receiver for a 2005 Dodge Ram 1500 is part # 65033, not part # 65046 which is for a 2500/3500 model. The 1500 frame is quite a bit different than the 2500/3500 frames which is why you cannot swap front mount trailer hitches between them.
view full answer... - Front Hitch Recommendation for 2007 Dodge Ram 2500 that Does Not Require Trimming
- The Draw Tite front hitch part # 65046 will fit your 2007 Dodge Ram 2500 and will not require you to trim the air damn.
We installed this on a 2007 just like yours, see link, and it did not require trimming.
view full answer... - Why Does Tow Hook of 2006 Dodge Ram Need Grinding to Install Front Hitch 65046
- Sounds like you have a Laramie trim level on your 2006 Dodge Ram 2500. We have found that the Laramie models require slight grinding of the tow hooks to allow the hitch part # 65046 to install. I wish there was a way around the grinding but it's the best option.
view full answer... - Front Hitch Recommendation for a 2007 Dodge Ram 2500
- The Draw Tite Hitch part # 65046 that you referenced has been confirmed to fit your 2007 Dodge Ram so I would recommend it for you. I attached an install video for you to check out as well.
For a snow plow I would recommend the K2 # K2AVAL8219 because of how well it works and how easy it is to use.
view full answer... - Kayak and Bike Carrying Options for 2006 Ram 2500 Long Bed Towing Travel Trailer
- Since I do not know the length or weights of your kayaks, nor how many bikes you need to transport, I will try to give you the most helpful general guidance so you can determine the best option for your 2006 Ram 2500 long bed. You can always get back to me with the specifics on these items to let me make more targeted recommendations.
One way you could go is to install a front-mount hitch like # 65046 and use a load support like # EM07605 along with a cab roof rack, like the Thule rack
view full answer... - How to Determine if a Front Mount Trailer Hitch Will Fit a 2006 Dodge Ram 3500 with Grille Guard
- Usually, grille guards and front mount hitches will use some if not all of the same mounting locations on the truck. You will have to look at where your grille guard is installed and compare that to the instructions for front hitch # 65046, which I have linked for you, to determine if there will be interference. I have also included a link to a video showing a typical installation that should help.
view full answer...
Info for these parts were:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Brandon M
Expert Research:
Adam R
Expert Research:
Jeffrey L
Written by:
Lindsey S
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Isabelle B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Pete
11/13/2013
Will this fit a 2008 3500 Dully 4 wheel drive?