To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Low-profile, aerodynamic crossbar lets you build an aftermarket roof rack for your vehicle. Aluminum bar has a T-slot that lets you mount channel-mounted carriers and accessories. Rubber strip in T-slot keeps out dirt and won't need trimming.
Features:
Inno Aero Aluminum Load Bar - Black - 51" Long - Qty 1:Specs:
Inno Aero Aluminum Load Bar - Black - 51" Long - Qty 1:Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today on our 2008 Nissan Altima, we're gonna be test fitting Inno Square bar roof rack system consisting of part numbers, INB117. These are the Inno Square Crossbars, 46 inches long, part number INSUT, these are Inno Feet for the Square Crossbars and finally part number INK116. This is the custom Fit Kit for the Inno Roof Rack System. The Inno Square Bar Roof Rack System is great for carrying a wide variety of accessories on your roof while freeing up space inside your vehicle. This can carry anything from bike racks to cargo baskets to cargo boxes. While the Square Bars are strong and sturdy, they are gonna make some noise while you drive.
Etrailer.com does carry a wide variety of Fairings that you could attach to these bars to help cut down that noise while you drive. This is very easy to install, it simply clamps around your existing doorframe and has padding where it's gonna make contact with the roof so it's not gonna have any scratches or abrasions on it while you travel.This is rubber coated, the clamp is and that's also to help protect your vehicle. The end caps do come with these locks included for anti theft and these also serve as integrated turn knobs to tighten this up against your roof as well. Now to give you a couple quick measurements, from the center of the roof to the bottom of the bar is gonna be two and three quarter inches from the center to the top is gonna be three and three quarter inches, so that's more than enough space for your accessories to wrap around your bars to be attached without damaging your roof. Now the carrying capacity for the roof rack is gonna be 220 pounds, however you always want to double check with your vehicles' manufacturers recommendations before you place anything on there to make sure it can withstand those weights.
Now that we've gone over some of the features of the roof rack system, lets go ahead and show you how it installs.We already have our front bar installed on our vehicle and we'll show you how we got the measurements for that a little bit later. We have our rear bar partially assembled on our table here. We'll finish this up and then we'll start installing it on our vehicle. So we'll first place our foot on and to open up the portion where our square bar's gonna fit through, you just push down on the lever there, you can kinda see it on the inside here where that moves so you can move it back and forth on the bar. Measure out how far we need to go forward.
And this is gonna be in your instructions but it's actually gonna be as a measurement from the end of one bar to the end of the other. All right, with everything measured out properly, we'll take our end cap and that just pushes into place. And we'll flip it upside down and start installing our Fit Kit. Start by putting our rubber pad into place, matches up at the bottom there and it just pushes in.These are numbered, so just be sure you're putting the right pad in the right place according to the instructions. And finally, we'll install our clamp.
We'll start by removing the end cap here and just twist it right off like so, and we'll remove our bracket. Now we can place our clamp on like so, put our bracket back in place. You want to make sure it stays in this position even as you tighten it down on the vehicle. And then we'll just loosely place our end cap back on. Now we're ready to set this on our vehicle, we'll start by opening up the doors and taking some measurements. How we got the front bar into it's position, I measured from the center of the door jamb to the center of the front bar. When we place the rear bar in place, we'll go from the rear door jamb to the back.I measure that out on both sides to keep it even. With that done, we'll tighten up our end cap until our clamp is just snug around our door jamb. We'll do that on both sides and then we'll go back and forth and tighten it down evenly. Once it's nice and tight, we'll push in on our end cap, line it up with the hole at the top here. Push that in, and lock it into place. Now we're ready to load up our gear and hit the road. And there you have it for the Inno Square Bar Roof Rack System on our 2008 Nissan Altima.
Average Customer Rating: 4.8 out of 5 stars (124 Customer Reviews)
Low-profile, aerodynamic crossbar lets you build an aftermarket roof rack for your vehicle. Aluminum bar has a T-slot that lets you mount channel-mounted carriers and accessories. Rubber strip in T-slot keeps out dirt and won't need trimming.We recently purchased 2 kayaks & Thule roof racks from our local outdoor store.
After waiting 2 weeks for our roof racks and J bars to come in we found that the Thule racks did not fit our 2017 Lincoln MKX and they didn't make any racks that would. The vehicle does not have roof racks and has a moon roof.
After a couple of days searching the internet we discovered etrailer.com. We found the Inno roof racks, but still was not sure they would work. We spoke to a repesenative and he assured us that the racks we chose would fit and the Thule J bars we did return would also work. As you can see by the photos 2 days later we were happy Kayakers.
Racks were perfect for my Acura MDX. They fit like a glove and I have used them several times.
I bought these as part of a kit with 60" Aero bars and the appropriate kit for my 14 Flex. I spent probably an hour and a half double checking my measurements and getting them torqued down properly. I spaced the bars on top of the car just a little wider than proscribed because I was planning on carrying 4x8 plywood, and it looked better to my eye. One thing to watch for: The instructions for the car-specific kit (in my case INK263) show the foot spacing measurements for a square bar, and the measuring point for these feet and Aero bars is different. That measurement point is indicated in the instructions for the feet, not the kit. Same numbers, just different reference point. Otherwise, they look good and are rock solid.
worked as expected, I used them to carry my hobie outback kayak (about 100lbs) on my Honda Civic 2016 Coupe (2 doors). They worked with no problem so far (1 year) even under high speed like 70mph.
Great racks. High quality parts. Fit perfectly. Went together easily.
Has worked great for transporting my fishing Kayak as well as small loads of lumber. It has worked fine for about a dozen and a half boards at a time or a couple of sheets of plywood. Just make sure that you have a good way to strap them down as well as maybe a rubber mat to help hold everything in place. The noise from it on the high way can be a lot but certainly not as bad as some that I have heard. I figure that anything on the outside of a vehicle like that will produce some noise.
Started assembly last summer and finally completed installation this spring. Directions took a lot of attention to detail but were adequate. Rack went on car securely and looks great. Have attached kayak rack and a roof pod and both worked flawlessly. Would definitely recommend.
This kit does not fit well. All measurements have been double and triple checked down to the millimeter. The lock on the covers interfere with the hooks. You have to apply so much pressure to get it to close that it makes the rack come loose. Not very satisfied
Noticed box was taped up more then usual, found other manuals that was not specifically for this, and also found one of the feet already had been mounted as there was scratches on the plastic and metal parts
I have had countless bike racks over the years and this is by far the best system I have ever had. Fits like a glove on my F150. Easy to install, looks great and the bikes do not move when on the roof.
I’ve had the system in place for over a year now and haul dual kayaks often! I love it! The only thing I wish I could change is the wind noise that’s comes with it. But I’m sure with any rook rack system you get that.
I did a lot of searching before selecting this rack for my Durango RT (no factory roof rails). It is easy to reinstall once the initial process is followed, I marked my doorjambs with a sharpie and it is easy to set up. Great product!
Installed incredibly quickly on my 2014 Prius V with some of the best instructions I could have ever asked for. Used the video as well in tandem and got it on the car in about an hour and a half with my partner. It was a lovely experience, which is sometimes difficult for couples to say in situations like this!
There work great and were easy to install. e-trailer rocks and so does Justin.
Installation was a little tricky but once the "feet" were attached to the roof and the bars properly spaced, everything wrapped up very well.
There is no noticeable wind noise with these installed.
It was an easy install with instructions. The rack has held up well so far and looks good on the car.
One was extremely hard to get on compared to the others (not sure if it had some rough machining or something), but once all we’re on, all was good
thanks to Adam for help and competent approach. Adam listened impeccably and in the shortest possible time helped to deliver the goods I needed
Very easy to use
Easy to mount and use. Very sturdy aswell. Measurements are a bit off on width adjustment.
Once I realized which bar was the front one and which was the back it was a fairly easy install. Since the measurements for the foot placement were wrong in the instructions I would suggest not tightening the feet all the way to the bars until you put it on the car. It would have been nice if both sets of rubber pads were the same, with the tunnel hook, and if they had adhesive backing to avoid losing them. I added 2 sided tape.
Tule and Yakima did not have a rack for my Nissan murano. So it was a blessing to find the immo rack. It seems like it can fit any car model. It's strong and secure. I feel my equipment will be safe with this rack.
These feet are easy to use and go well wit the Inno system. I was worried since my car did not come with any roof racks, but this is the solution to haul things on my roof. They work well and are very secure.
These are made perfectly for your vehicle. They are very secure when combined with the other Inno products. No worries of the rack system coming off. Using them to transport kayaks using kayak holders.
Installation went pretty smoothly. The trick is to fully understand each step before moving to the next. There are a lot of small parts which at first was a little intimidating, but soon I was able to "get with it". I love the finished product and think you helped me get a good deal. Thank you for that
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.