Dimensions for Mounting Kit for Rhino-Rack Batwing Awning RR25FJ

Question

Question:

Can you tell me the distance between the drilled holes, center to center, of the 3 drilled holes in the 6inch arm of the mounting bracket.

asked by: Jim L

0

Expert Reply:

I would be happy to! We have taken quite a few measurements of the brackets for the Mounting Kit for Rhino-Rack Batwing Awning item # RR25FJ. Pretty sure the spacing you're asking for is 1-3/8" but there are a lot of holes so I went ahead and attached a couple of diagrams below that I am confident will answer your question.

expert reply by: Jerred H

0

Rhino-Rack Batwing Awning
(click to enlarge)

Answer 1

I attached a picture that has the dimensions of the brackets of the Mounting Kit for Rhino-Rack Batwing Awning #RR25FJ that you referenced.

view full answer...

Answer 2

I can't post that picture because it's from another website but the distance between the top hole and the center hole of the ARB Universal Awning Bracket item #ARB57FR is 2". This is a center to center measurement. These holes are oblong…

view full answer...

Answer 3

The BAK Revolver X4 Hard Tonneau Cover - Roll Up - Aluminum and Vinyl - Matte Black part #BAK79602 that you have asked about weighs in at just over 70 lbs. including the rails. As far as carrying a load on the top of it it is rated for up to 400 lbs.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

Hello Dan, Great question. When you’re comparing the Firestone kits #F59VV and #F2582, they both technically fit your 2025 F-150, but they are designed around different mounting locations and truck configurations. The #F2582 is the traditional…

view full answer...

Answer 12

Hey Douglas, whenever available I recommend going with the HD version of the Roadactive kits like the part #RAS3611-YHD that fits your 2022 Ford F-150 4WD. The extra capacity of this kit over the non-HD basically doesn't have any downside aside…

view full answer...

Dimensions for Mounting Kit for Rhino-Rack Batwing Awning RR25FJ

Continue Researching