Replacement Jack For A Shelby 5856A That Uses The Same Mounting Plate

Question

Question:

Which jack should I get to replace this shelby 5856a without having to cut and weld a new one on

asked by: James W

0

Expert Reply:

The Fulton Round, Snap-Ring Swivel Marine Jack # FTJ120W0301 will fit the same trailer mount as the Shelby 5856A.

The trailer jack has a heavy-gauge steel construction. It has a 600-hour salt spray rating which makes it ideal for marine and recreational use. The jack has a lift capacity of 1,200 pounds.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

What we have heard is that the Fulton #FTJ120W0301 does fit the mounting plate of the Shelby Jack 5784.

view full answer...

Answer 2

What we have heard is that the Fulton #FTJ120W0301 does fit the mounting plate of the Shelby Jack 5784. This will be your best option. This jack has a 1,200 lb lifting capacity which would be more than enough.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Replacement Jack For A Shelby 5856A That Uses The Same Mounting Plate

Featured Help Information

Miscellaneous Media

Continue Researching