Replacement Jack Solution for 2008 Viking Epic 1706

Question

Question:

Im looking for a replacement tongue jack for a 2008 Viking Epic 1706. Ours has stopped working and has a welded on Jack now.

asked by: Andrew N

0

Expert Reply:

I pulled up pictures of your 2008 Viking Epic 1706 and found that it uses a side mount trailer jack. So since it is welded on you could use a Pro Series swivel jack part # PSEJ10000101 mounted on the other side since this would bolt on with included u-bolts. Or if you wanted to try and mount a new jack to your current mount I would need to know what brand and model jack you have now.

expert reply by: Jameson C

0

Answer 1

Can you get me the diameter of the axle or the capacity if you can find it? Most likely it's a 2k axle and the kit part #BK1-100 would be the correct kit to use but I'd need to verify that for sure. The correct diameter axle for a 2k axle…

view full answer...

Answer 2

In order to confirm the correct replacement bearings for your 2004 Viking Epic Series M-1906 we need to know your axle capacity. The axle capacity can be found on a sticker located in the center of the axle tube. I have attached a list of options for…

view full answer...

Answer 3

Hi Andy; Atwood has been gone for quite a while now so their couplers and repair kits are no longer around. The best option is to replace the coupler on your trailer. I recommend the Demco A-Frame Trailer Coupler #DM14793-81. This uses the eZ latch…

view full answer...

Answer 4

First and foremost, thank you for your service to our country. It is greatly appreciated. Ultimately you are correct that the most accurate way to determine the correct hub and drum assembly is to pull the hub and find the bearing and grease seal…

view full answer...

Answer 5

What you've got there looks like some type of proprietary mount that we don't offer. We do however have jacks that would work. I'd recommend having the mount removed and using a weld-on jack like the Fulton #FXP100W0301 and the #P9012-00…

view full answer...

Answer 6

I do have an option for you but Atwood was bought out and their replacement parts are no longer available, including the repair kit you would need. The best option is to replace that A-frame coupler with a new one that attaches to a 2 inch hitch…

view full answer...

Answer 7

For a wheel and tire combo for your 2003 Viking Epic 1706 in the size of 4.80-12 the Kenda 4.80-12 on Aluminum Wheel part #AM30677 would work great.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Replacement Jack Solution for 2008 Viking Epic 1706

Continue Researching