Recommended Storage Cover for Enclosed Car Trailer

Question

Question:

We need a cover to fit an enclosed car trailer. 24’ plus nose and extended tongue is approx 30’ total. Is 98” tall and 98” wide with full door/ramp in rear and side door is 48”. Ty

asked by: Lisa T

0

Expert Reply:

I recommend you select a toy hauler type storage cover. I suggest the Adco SFS AquaShed RV Cover for Toy Hauler Travel Trailer, # 290-52273. This has actual dimensions of 342" long x 106" wide x 120" tall.

expert reply by: Michael R

0

Answer 1

Item #290-52244 is too tight for your 2014 Work and Play 25ULA toy hauler since it only has a width of 100". Adco does have other covers designed for trailers that are up to 28' long such as Adco's SFS AquaShed Cover for Toy Hauler…

view full answer...

Answer 2

The best cover for your 2017 Grand Design Imagine 2150RB is one from Adco, with the correct fit being the following: - Adco Polypropylene Storage Lot RV Cover for Travel Trailer #290-74844 This cover is a fit for travel trailers that measure…

view full answer...

Answer 3

The specs for a 2019 Jayco Jay Flight SLX 224BH Travel Trailer shows a length of 26.5' so the #290-52243 wouldn't be long enough. Instead I recommend theAdco Polypropylene Storage Lot RV Cover for Travel Trailer - Up To 28-1/2' Long…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Recommended Storage Cover for Enclosed Car Trailer

Products Featured in This Question

Continue Researching